The Electrical Response of Real Dielectrics: Using the Voltage Ramp Method as a Straightforward Diagnostic Tool for Polymeric Composites.

An experimental method exploiting the capacitive response of most materials is here revised. The procedure called the "Voltage Ramp Method" (VRM) is based on applying proper voltage ramp cycles over time and measuring electrical current intensity flowing through the material sample. In the case of an ideal capacitor, a current plateau should be easily measured, and the capacitance value precisely determined. However, most media, e.g., semiconductors and insulating polymers, show dielectric absorption and hence electric leakage effects. Therefore, the VRM method allows simultaneous determination of their equivalent capacitance and resistance. Some case studies are discussed as concerning the application of VRM to both standard and actual media. A figure of merit of the method is the percentage difference between 2.5% and 1.5% with respect to the nominal values of a commercial capacitor and resistor, respectively. The simulation modeling of the material electrical response is compared to the experimental data also on polymer nanocomposites suitable for energy harvesting.

Cathode Active Material Recycling from Spent Lithium Batteries: A Green (Circular) Approach Based on Deep Eutectic Solvents.

The transition to a circular economy vision must handle the increasing request of metals required to satisfy the battery industry; this can be obtained by recycling and feeding back secondary raw materials recovered through proper waste management. Here, a novel and green proof-of-concept was developed, based on deep eutectic solvents (DESs) to fully and easily recover valuable metals from various cathode active materials, including LiMn2 O4 , LiNi0.5 Mn1.5 O4 , and LiNi0.8 Co0.2 O2 . DES composed of choline chloride and lactic acid could leach Li, Mn, Co, and Ni, achieving efficiency of 100 % under much milder conditions with respect to the previous literature. For the first time, to our best knowledge, a two-step approach was reported in the case of LiNi0.8 Co0.2 O2 for selective recovery of Li, Co, and Ni with high yield and purity. Furthermore, other cathode components, namely aluminum current collector and binder, were found to be not dissolved by the proposed DES, thus making a simple separation from the active material possible. Finally, this strategy was designed to easily regenerate and reuse the leaching solvents for more than one extraction, thus further boosting process sustainability.

Li+ Dynamics of Liquid Electrolytes Nanoconfined in Metal-Organic Frameworks.

Metal-organic frameworks (MOFs) are excellent platforms to design hybrid electrolytes for Li batteries with liquid-like transport and stability against lithium dendrites. We report on Li+ dynamics in quasi-solid electrolytes consisting in Mg-MOF-74 soaked with LiClO4-propylene carbonate (PC) and LiClO4-ethylene carbonate (EC)/dimethyl carbonate (DMC) solutions by combining studies of ion conductivity, nuclear magnetic resonance (NMR) characterization, and spin relaxometry. We investigate nanoconfinement of liquid inside MOFs to characterize the adsorption/solvation mechanism at the basis of Li+ migration in these materials. NMR supports that the liquid is nanoconfined in framework micropores, strongly interacting with their walls and that the nature of the solvent affects Li+ migration in MOFs. Contrary to the "free'' liquid electrolytes, faster ion dynamics and higher Li+ mobility take place in LiClO4-PC electrolytes when nanoconfined in MOFs demonstrating superionic conductor behavior (conductivity σrt > 0.1 mS cm-1, transport number tLi+ > 0.7). Such properties, including a more stable Li electrodeposition, make MOF-hybrid electrolytes promising for high-power and safer lithium-ion batteries.

Is It Possible to Obtain Solvent-Free, Li+ -Conducting Solid Electrolytes Based on Pure PVdF? Comment on "Self-Suppression of Lithium Dendrite in All-Solid-State Lithium Metal Batteries with Poly(vinylidene difluoride)-Based Solid Electrolytes".

Is It Possible to Obtain Solvent-Free, Li+ -Conducting Solid Electrolytes Based on Pure PVdF? Comment on "Self-Suppression of Lithium Dendrite in All-Solid-State Lithium Metal Batteries with Poly(vinylidene difluoride)-Based Solid Electrolytes".

Aqueous Processing of Na0.44MnO2 Cathode Material for the Development of Greener Na-Ion Batteries.

The implementation of aqueous electrode processing of cathode materials is a key for the development of greener Na-ion batteries. Herein, the development and optimization of the aqueous electrode processing for the ecofriendly Na0.44MnO2 (NMO) cathode material, employing carboxymethyl cellulose (CMC) as binder, are reported for the first time. The characterization of such an electrode reveals that the performances are strongly affected by the employed electrolyte solution, especially, the sodium salt and the use of electrolyte's additives. In particular, the best results are obtained using the 1 M solution of NaPF6 in EC/DEC (ethylene carbonate/diethyl carbonate) 3:7 (v/v) + 2 wt % FEC (fluoroethylene carbonate). With this electrolyte, the outstanding capacity of 99.7 mA h g-1 is delivered by the CMC-NMO cathode after 800 cycles at a 1C charge/discharge rate. On the basis of this excellent long-term performance, a full sodium cell, composed of a CMC-based NMO cathode and hard carbon from biowaste (corn cob), has been assembled and tested. The cell delivers excellent performances in terms of specific capacity, capacity retention, and long-term cycling stability. After 75 cycles at a C/5 rate, the capacity of the NMO in the full-cell approaches 109 mA h g-1 with a Coulombic efficiency of 99.9%.

Polymer and Composite Membranes for Proton-Conducting, High-Temperature Fuel Cells: A Critical Review.

Polymer fuel cells operating above 100 °C (High Temperature Polymer Electrolyte Membrane Fuel Cells, HT-PEMFCs) have gained large interest for their application to automobiles. The HT-PEMFC devices are typically made of membranes with poly(benzimidazoles), although other polymers, such as sulphonated poly(ether ether ketones) and pyridine-based materials have been reported. In this critical review, we address the state-of-the-art of membrane fabrication and their properties. A large number of papers of uneven quality has appeared in the literature during the last few years, so this review is limited to works that are judged as significant. Emphasis is put on proton transport and the physico-chemical mechanisms of proton conductivity.

Correlation between Deposition Parameters and Hydrogen Production in CuO Nanostructured Thin Films.

In this article, we report a systematic investigation of the role of (i) substrate temperature, (ii) oxygen partial pressure, and (iii) radio frequency (rf) power on the crystal structure and morphology of CuO nanostructured thin films prepared by means of rf-magnetron sputtering starting from a Cu metal target. On selected films, photocatalytic tests have been carried out in order to correlate the structural and morphological properties of the thin films prepared under different conditions with the photocatalytic properties and to find out the key parameters to optimize the CuO nanostructured films. All of the synthesized films were single-phase CuO nanorods of variable diameter between 80 and 200 nm. Better-aligned rods were obtained at relatively low substrate temperatures and from low to intermediate oxygen partial pressures, resulting in more efficient photocatalytic activities. Our investigation suggests a relevant role of the crystallographic orientation of the CuO tenorite film on the photocatalytic activity, as demonstrated by the significant improvement in H2 evolution for highly oriented films.

Nanoscale stabilization of the scheelite-type structure in La(0.99)Ca(0.01)NbO4 thin films.

In this paper we report on the deposition of La0.99Ca0.01NbO4 thin films with scheelite-type crystal structure. Thanks to the film's nanostructure, we were able to stabilize the tetragonal scheelite-type structure phase at room temperature, which involves a full removal of the fergusonite-scheelite phase transition.

Facile and green assembly of nanocomposite membranes for fuel cells.

We report on a facile spray deposition method, which allows obtaining nanocomposite membranes for high-temperature polymer fuel cells characterized by high homogeneity and excellent proton conductivity. The proposed method is also green, as it requires much smaller amounts of solvents with respect to standard casting.

Increasing the antibacterial effect of lysozyme by immobilization on multi-walled carbon nanotubes.

We report a facile strategy to obtain multiwalled carbon nanotubes (MWCNTs) functionalized with covalently bonded lysozyme. The functionalization procedure has been investigated by means of several techniques, including thermogravimetry, Raman spectroscopy, transmission electron microscopy, and cyclic voltammetry. A functionalization of about 1 lysozyme molecule every 4000 carbon atoms is obtained. The modified lysozyme-CNTs nanocomposite shows a significant increase of the antibacterial activity towards the Gram-positive S. aureus if compared with lysozyme in solution.

Structure-property interplay of proton conducting membranes based on PBI5N, SiO2-Im and H3PO4 for high temperature fuel cells.

Polybenzimidazoles (PBIs) are among the polymers of choice to prepare membranes for high temperature polymer fuel cells. Poly-2,2'(2,6-pyridine)-5,5'-bibenzimidazole (PBI5N), doped with H(3)PO(4), and acid-doped PBI5N containing 10 wt% of imidazole-functionalized silica membranes were studied with thermogravimetric analysis, differential scanning calorimetry, dynamic-mechanical analysis, infrared spectroscopy, and broadband electric spectroscopy to examine the structure-property relationships. Key results show that: (1) doped PBI5N membranes show thermal decomposition starting at 120 °C, while pristine PBI5N is stable up to 300 °C; (2) the presence of filler increases the acid uptake and decreases the crystallinity of PBI5N; (3) the addition of phosphoric acid reduces the mechanical properties of the membrane, while the addition of filler has the opposite effect; (4) acid-doped membranes have conductivity values on the order of 10(-2)-10(-3) S cm(-1); and (5) membranes exhibit a Vogel-Tamman-Fulcher (VTF) type proton conduction mechanism, where proton hopping is coupled with the segmental motion of the polymer chain. Infrared spectroscopy combined with DFT quantum mechanical calculations was used to assign the experimental spectrum of PBI5N.

Electrolytes for solid-state lithium rechargeable batteries: recent advances and perspectives.

This critical review presents an overview of the various classes of Li(+) conductors for use as electrolytes in lithium polymer batteries and all-solid state microbatteries. Initially, we recall the main models for ion transport and the structure-transport relationships at the basis of the observed conductivity behaviours. Emphasis is then placed on the physico-chemical and functional parameters relevant for optimal electrolytes preparation, as well as on the techniques of choice for their evaluation. Finally, the state of the art of polymer and ceramic electrolytes is reported, and the most interesting strategies for the future developments are described (121 references).

In vitro calcified matrix deposition by human osteoblasts onto a zinc-containing bioactive glass.

Bioactive glasses synthesized by the sol-gel technique possess many of the qualities associated with an ideal scaffold material for a bone graft substitute. In view of the potential clinical applications, we performed a detailed in vitro study of the biological reactivity of synthesized 58S bioactive glass containing-zinc, in terms of osteoblast morphology, proliferation, and deposition of a mineralized extracellular matrix (ECM). Human Sarcoma Osteoblast (SAOS-2) cells were used to i) assess cytotoxicity by lactate dehydrogenase (LDH) release and ii) evaluate the deposition of a calcified extracellular matrix by ELISA assay and quantitative RT-PCR (qRT-PCR). In comparison with pure silica and 58S, the 58S-Zn0.4 bioglass showed a significant increase in cellular proliferation and deposition of ECM components such as decorin, fibronectin, osteocalcin, osteonectin, osteopontin, type-I and -III collagens. Calcium deposition was significantly higher than on pure silica and 58S samples. Also Alkaline phosphatase (ALP) activity and its protein content was higher with respect to pure silica and 58S. qRT-PCR analysis revealed the up-regulation of type-I collagen, bone sialoprotein and osteopontin genes. All together these results demonstrate the cytocompatibility of 58S-Zn0.4 bioglass and its capability to promote osteoblast differentiation.

Multi-walled carbon nanotubes as the gas chromatographic stationary phase: role of their functionalization in the analysis of aliphatic alcohols and esters.

Presented hereafter is the novel application of differently functionalized multi-walled carbon nanotubes (f-MWCNTs) as stationary phases for the GC separation of C(1)-C(5) alcohols and esters. Low-cost packed columns, easily prepared in laboratory, were used with satisfactory results. Depending on the functional groups introduced on the pristine MWCNTs, remarkably different behaviours have been observed, thus indicating that derivatization is a key factor to achieve optimal resolution. The best performance was shown by the 2,2'-(ethylenedioxy)diethylamine derivatized MWCNTs, allowing the separation of alcohol isomers, for this reason chosen for the investigation of fermentation by-products in distilled spirits. The degree of derivatization has been assessed for each packing material by thermogravimetric analysis (TGA). A computational study has been performed to correlate the physico-chemical properties of alcohol probes with the retention behaviour.

Separation of alkanes and aromatic compounds by packed column gas chromatography using functionalized multi-walled carbon nanotubes as stationary phases.

In the present work, we show a novel application of pristine and functionalized Multi-Walled Carbon Nanotubes (MWCNTs) as stationary phase in low-cost packed columns for the gas chromatographic separation of alkanes and aromatic hydrocarbons. The MWCNTs were deeply investigated by means of physical and chemical methods, like thermal analysis, IR and atomic force microscopy, and Inverse Gas Chromatography (IGC) in order to correlate the adsorption process and surface properties with the material purity level and functionalization degree. The derivatization process of the pristine nanotubes was a key factor to achieve a successful separation of both the light n-alkanes (C3-C5) and the related isomers (C4-C5 branched alkanes). Satisfactory results were similarly obtained in the case of separation of aromatic hydrocarbons (BTX).

In vitro enhancement of SAOS-2 cell calcified matrix deposition onto radio frequency magnetron sputtered bioglass-coated titanium scaffolds.

In bone tissue engineering, bioglass coating of titanium (Ti) scaffolds has drawn attention as a method to improve osteointegration and implant fixation. In this in vitro study, bioactive glass layers with an approximate thickness of 1 microm were deposited at 200 degrees C onto a three-dimensional Ti-6Al-4V scaffold using a radio frequency (r.f.) magnetron sputtering system. After incubation with SAOS-2 human osteoblasts, in comparison with the uncoated scaffolds, the bioglass-coated scaffolds showed a twofold increase in cell proliferation (p < 0.05) up to 68.4 x 10(6), and enhanced the deposition of extracellular matrix components such as decorin, fibronectin, osteocalcin, osteonectin, osteopontin, and type-I and -III collagens (p < 0.05). Calcium deposition was twofold greater on the bioglass-coated scaffolds (p < 0.05). The immunofluorescence related to the preceding bone matrix proteins and calcium showed their colocalization to the cell-rich areas. Alkaline phosphatase activity increased twofold (p < 0.001) and its protein content was threefold higher with respect to the uncoated sample. Quantitative reverse transcriptase-polymerase chain reaction analysis revealed upregulated transcription specific for type-I collagen and osteopontin (p < 0.001). All together, these results demonstrate that the bioglass coating of the three-dimensional Ti scaffolds by the r.f. magnetron sputtering technique determines an in vitro increase of the bone matrix elaboration and may potentially have a clinical benefit.

A photocatalytic water splitting device for separate hydrogen and oxygen evolution.

A two-compartment Plexiglas cell has been set up and tested for separate hydrogen and oxygen production from photocatalytic water splitting on a thin TiO2 layer deposited by magnetron sputtering on a flat Ti electrode inserted between the two cell compartments.

Multiwalled carbon nanotube chemically modified gold electrode for inorganic As speciation and Bi(III) determination.

A chemically modified gold electrode has been conveniently prepared by binding multiwalled carbon nanotubes (MWCNTs) to which thiol functions have been tethered. The electrode has been characterized by atomic force microscopy and oxidative desorption experiments and gives excellent results for trace determination of As(III) and Bi(III) in natural and high-salinity waters, overcoming the limitation typical of solid electrodes. A mechanism for As(III) preconcentration at the electrode is proposed and supported by results obtained by two similar chemically modified electrodes (CMEs), the first one prepared with single-walled carbon nanotubes and the second one with a monolayer of (biphenyl)dimethanethiol. The performance obtained with the MWCNTs-CME largely overcomes that obtained by using other devices.