Impact of effluent parameters and vancomycin concentration on vancomycin resistant Escherichia coli and its host specific bacteriophage lytic activity in hospital effluent.

Vancomycin resistance in bacteria has been classified under high priority category by World Health Organization (WHO) and its presence in hospital effluent is reported to be increasing owing to excess antibiotics use. Among various strategies, bacteriophage has been recently considered as a promising biological agent for combating such antimicrobial resistant bacteria (ARB). However, the influence of effluent's properties on phage-ARB interaction in actual hospital effluent is not completely understood. The present works intends to study this influence of hospital effluent and its parameters on the interaction between vancomycin resistant E. coli (VRE) and its host specific bacteriophage. The isolated VRE was identified by 16S rRNA sequencing, matrix-assisted laser desorption/ionization-time of flight (MALDI - TOF) and whole genome sequencing. The infectivity of phage onto host bacteria was investigated using electron microscopic techniques, dynamic light scattering (DLS), spectrofluorophotometer and confirmed using double agar overlay method. The monovalency and polyvalency of isolated phage against various bacterial species were determined. The phage morphology was identical to T7 phage belonging to Podoviridae. The phage lysis was maximum at pH 7 (90.2%), 37 °C (91.6%) and vancomycin concentration of 50 µg/mL in both synthetic media (89.13%) and effluent (100%). At a maximum vancomycin concentration of 100 µg/mL, decrease in Ca, K, Mg and P (up to 19.70, 14.18, 28, and 15.82% respectively) concentration in effluent was observed due to phage infectivity when compared to control. The whole genome sequencing was performed and the bioinformatics analysis presented the role of mdfA gene encoding the efflux pump in causing vancomycin resistance in E. coli. It also depicted the presence of multiple genes responsible for mercury, cobalt, zinc and cadmium resistance in VRE. These results clearly indicate that bacteriophage mediated combating of VRE is possible in actual hospital effluent and can be used as one of the treatment methods.

Enhanced super-hydrophobic and switching behavior of ZnO nanostructured surfaces prepared by simple solution--immersion successive ionic layer adsorption and reaction process.

A simple and cost-effective successive ionic layer adsorption and reaction (SILAR) method was adopted to fabricate hydrophobic ZnO nanostructured surfaces on transparent indium-tin oxide (ITO), glass and polyethylene terephthalate (PET) substrates. ZnO films deposited on different substrates show hierarchical structures like spindle, flower and spherical shape with diameters ranging from 30 to 300 nm. The photo-induced switching behaviors of ZnO film surfaces between hydrophobic and hydrophilic states were examined by water contact angle and X-ray photoelectron spectroscopy (XPS) analysis. ZnO nanostructured films had contact angles of ~140° and 160°±2 on glass and PET substrates, respectively, exhibiting hydrophobic behavior without any surface modification or treatment. Upon exposure to ultraviolet (UV) illumination, the films showed hydrophilic behavior (contact angle: 15°±2), which upon low thermal stimuli revert back to its original hydrophobic nature. Such reversible and repeatable switching behaviors were observed upon cyclical exposure to ultraviolet radiation. These biomimetic ZnO surfaces exhibit good anti-reflective properties with lower reflectance of 9% for PET substrates. Thus, the present work is significant in terms of its potential application in switching devices, solar coatings and self-cleaning smart windows.

Remote monitoring of a multi-component liquid-phase organic synthesis by infrared emission spectroscopy: the recovery of pure component emissivities by band-target entropy minimization.

A liquid-phase cycloaddition reaction near ambient temperature involving dimethyl acetylenedicarboxylate (DMAD) and cyclopentadiene (CP) as reactants was measured using a conventional Fourier transform infrared (FT-IR) spectrometer with an emission accessory. Two semi-batch experiments were performed and a total of 55 spectra were collected using a DTGS detector. Band-target entropy minimization (BTEM), a pure component spectral reconstruction technique, was applied to analyze the data set to retrieve the pure component emission spectrum from the reaction system. The estimated emission spectra of the solvent chloroform, DMAD, CP, and product, namely dimethyl bicyclo[2.2.1]-2,5-heptadiene-2,3-dicarboxylate, were all reconstructed with rather good quality. The estimated emission spectra are similar to independent FT-IR spectra of the same cycloaddition reaction. Using a least squares fit, the relative concentration profiles of the species are obtained. Because this appears to be the first time that a liquid-phase reaction has been monitored by infrared emission spectroscopy, further improvements and opportunities for general multi-phase liquid reaction monitoring are discussed.

Application of band-target entropy minimization to infrared emission spectroscopy and the reconstruction of pure component emissivities from thin films and liquid samples.

Thermal emission spectral data sets were collected for a thin solid film (parafilm) and a thin liquid film (isopropanol) on the interval of 298-348 K. The measurements were performed using a conventional Fourier transform infrared (FT-IR) spectrometer with external optical bench and in-house-designed emission cell. Both DTGS and MCT detectors were used. The data sets were analyzed with band-target entropy minimization (BTEM), which is a pure component spectral reconstruction program. Pure component emissivities of the parafilm, isopropanol, and thermal background were all recovered without any a priori information. Furthermore, the emissivities were obtained with increased signal-to-noise ratios, and the signals due to absorbance of thermal radiation by gas-phase moisture and CO2 were significantly reduced. As expected, the MCT results displayed better signal-to-noise ratios than the DTGS results, but the latter results were still rather impressive given the low temperatures used in this study. Comparison is made with spectral reconstruction using the orthogonal projection approach-alternating least squares (OPA-ALS) technique. This contribution introduces the primary equation for emission spectral reconstruction using BTEM and discusses some of the unusual characteristics of thermal emission and their impact on the analysis.

A fluorescence polarization-based assay for peptidyl prolyl cis/trans isomerase cyclophilin A.

Peptidyl prolyl cis/trans isomerase cyclophilin A (CypA) serves as a cellular receptor for the important immunosuppressant drug, cyclosporin A. In addition, CypA and its enzyme family have been found to play critical roles in a variety of biological processes, including protein trafficking, HIV and HCV infection/replication, and Ca(2+)-mediated intracellular signaling. For these reasons, cyclophilins have emerged as potential drug targets for several diseases. Therefore, it is extremely important to screen for novel small molecule cyclophilin inhibitors. Unfortunately, the biochemical assays reported so far are not adaptable to a high-throughput screening format. Here, we report a fluorescence polarization-based assay for human CypA that can be adapted to high-throughput screening for drug discovery. The technique is based on competition and uses a fluorescein-labeled cyclosporin A analog and purified human CypA to quantitatively measure the binding capacity of unlabeled inhibitors. Detection by fluorescence polarization allows real-time measurement of binding ratios without separation steps. The results obtained demonstrated significant correlation among assay procedures, suggesting that the application of fluorescence polarization in combination with CypA is highly advantageous for the accurate assessment of inhibitor binding.