On-surface photopolymerization of two-dimensional polymers ordered on the mesoscale.

The use of solid supports and ultra-high vacuum conditions for the synthesis of two-dimensional polymers is attractive, as it can enable thorough characterization, often with submolecular resolution, and prevent contamination. However, most on-surface polymerizations are thermally activated, which often leads to high defect densities and relatively small domain sizes. Here, we have obtained a porous two-dimensional polymer that is ordered on the mesoscale by the two-staged topochemical photopolymerization of fluorinated anthracene triptycene (fantrip) monomers on alkane-passivated graphite surfaces under ultra-high vacuum. First, the fantrip monomers self-assemble into highly ordered monolayer structures, where all anthracene moieties adopt a suitable arrangement for photopolymerization. Irradiation with violet light then induces complete covalent crosslinking by [4+4] photocycloaddition to form a two-dimensional polymer, while fully preserving the long-range order of the self-assembled structure. The extent of the polymerization is confirmed by local infrared spectroscopy and scanning tunnelling microscopy characterization, in agreement with density functional theory calculations, which also gives mechanistic insights.

Synthesis of well-ordered COF monolayers: surface growth of nanocrystalline precursors versus direct on-surface polycondensation.

Two different straightforward synthetic approaches are presented to fabricate long-range-ordered monolayers of a covalent organic framework (COF) on an inert, catalytically inactive graphite surface. Boronic acid condensation (dehydration) is employed as the polymerization reaction. In the first approach, the monomer is prepolymerized by a mere thermal treatment into nanocrystalline precursor COFs. The precursors are then deposited by drop-casting onto a graphite substrate and characterized by scanning tunneling microscopy (STM). While in the precursors monomers are already covalently interlinked into the final COF structure, the resulting domain size is still rather small. We show that a thermal treatment under reversible reaction conditions facilitates on-surface ripening associated with a striking increase of the domain size. Although this first approach allows studying different stages of the polymerization, the direct polymerization, that is, without the necessity of preceding reaction steps, is desirable. We demonstrate that even for a comparatively small diboronic acid monomer a direct thermally activated polymerization into extended COF monolayers is achievable.

Design of chemically activated polymer microwells by one-step UV-lithography for stem cell adhesion.

A novel method to produce sub-microwalled chemically activated polymer microwells by one-step UV-lithography under ambient conditions which are selectively coated with gelatin is introduced. The dimensions as well as the shape of the resulting polystyrene structures are both tunable merely by the irradiation time through one and the same mask. It is shown that the UV-irradiation initiates three effects at those surface areas which are not covered by the mask: (i) oxidation, (ii) cross-linking, and (iii) degradation of polystyrene. The superposition of those effects results in the formation of microscaled, oxidized polymer wells separated by polymer walls, whereas the polymer walls are formed below the mask structures. Topographical changes induced by the UV-irradiation are investigated by atomic force microscopy after different irradiation times. It is shown by X-ray photoelectron spectroscopy and ellipsometric investigations that the chemical composition of the irradiated areas and the degradation of polystyrene reach an equilibrium state after an irradiation time of 10 min. The lateral distribution of the cross-linked and oxidized and of the nonmodified polystyrene after irradiation was determined by fluorescence microscopy and time-of-flight secondary ion mass spectrometry. After the irradiated samples were treated with gelatin solution, it was found that stem cells selectively attach to the irradiated areas. This is due to the selective immobilization of the gelatin on the irradiated polymer areas, which was proved by X-ray photoelectron spectroscopy experiments.

TOF-SIMS analysis of structured surfaces biofunctionalized by a one-step coupling of a spacer-linked GRGDS peptide.

Time-of-Flight Secondary Ion Mass Spectrometry (TOF-SIMS) was applied to validate GRGDS peptide patterned surfaces. The structuring of the surfaces included several steps: micro contact printing (microCP), chemical etching and aminofunctionalization followed by chemical coupling of spacer-linked GRGDS peptides via an isothiocyanate anchor. TOF-SIMS analysis of characteristic ions and molecular fragments with a lateral resolution of 100 nm allowed proving the change in chemical properties of the surface with each step during the structuring process. We found that the application of polydimethylsiloxane as stamp material resulted in the contamination of the surface with this polymer. TOF-SIMS investigations, however, also showed that during the preparation process the contaminations were removed and do not influence the bio functionality of the surface patterns. The results of the surface analysis carried out with TOF-SIMS were confirmed by complementary cell adhesion experiments with murine fibroblasts. As a result, specific cell adhesion restricted to GRGDS peptide functionalized areas was obvious by the formation of focal adhesion contacts in the fibroblasts. Thus, TOF-SIMS is the method of choice in chemical characterization of surfaces in structuring and functionalization processes, because it offers the opportunity to follow surface contamination during the preparation process and to assess the influence of the contamination on the applicability of the final substrate.