Effects of natural products-based dentifrices on acrylic resin for denture bases: A simulated period of 4 years.

PURPOSE: To evaluate the antimicrobial activity of dentifrices based on Malva sylvestris and propolis and the effect on the acrylic resin. METHODS: The inhibitory effect against Candida albicans, Enterococcus faecalis and Streptococcus mutans was determined. The specimens of resin were divided into groups: Control (brushing with distilled water); brushing with Colgate; brushing with Protex; brushing with Malvatricin, brushing with Proporalcare Dental Gel and brushing with Green Propolis Dental Gel. Brushing was carried out in a brushing machine. Roughness and color were assessed. The data were analyzed by ANOVA, followed by the Bonferroni post test (α= 0.05). RESULTS: The products evaluated showed antimicrobial activity against all microorganisms (P< 0.05), except Proporalcare Dental Gel, which was not effective against E. faecalis. Greater roughness (P< 0.05) was observed in the samples treated with Colgate. The samples from control and Protex groups showed the lowest color variation and the highest luminosity, with a difference in relation to the others (P< 0.05), which showed higher values, although clinically acceptable. CLINICAL SIGNIFICANCE: The dentifrices based on natural products can be indicated for cleaning prostheses, since they showed antimicrobial activity and did not cause perceptible color changes of the resin tested. The dentifrices did not produce adverse effects on the surface of the resin or did so less than the conventional dentifrice.

Effect of silver vanadate on the antibiofilm, adhesion and biocompatibility properties of denture adhesive.

Aim: To evaluate the biological and mechanical properties of an adhesive with nanostructured silver vanadate (AgVO3). Materials & methods: Specimens in poly(methyl methacrylate) (PMMA) were treated with Ultra Corega Cream (UCCA) denture adhesive with or without AgVO3. Biofilms of Candida albicans, Candida glabrata and Streptococcus mutans were grown and the viable cells counted. Fluorescence microscopy was used. The viability of the VERO cell and adhesive strength were evaluated. Results: All concentrations of AgVO3 reduced the biofilm formation and showed no cytotoxic effect. At 5 min and 24 h, UCCA with 5 and 10% AgVO3 showed better performance, respectively. Conclusion: AgVO3 promoted the antibiofilm activity of the adhesive, with a positive effect on the adhesive strength, and was biocompatible.

What is this summary about? Some people wear false teeth called dentures. They use a special glue to keep these false teeth in their mouths. It is important to clean dentures well and remove the glue every day. If the dentures get dirty, they can cause infections of the gums. Doctors and dentists can help, but sometimes medicines do not work well. This study checked to see whether adding a medicine that can kill bacteria into the glue could stop gum swelling and other illnesses, or make them better. What were the results? The glue containing the medicine killed microbes like fungi and bacteria. It also stuck things together well and was safe to use. What do the results mean? Using this special glue could help people with dentures to avoid illness.

Silver-based gels for oral and skin infections: antimicrobial effect and physicochemical stability.

Aim: To systematically evaluate the literature on silver (Ag) gels and their antimicrobial efficacy and physicochemical stability. Materials & methods: A search was performed in PubMed/MEDLINE, LILACS, Web of Science, Scopus, Embase and Google Scholar. Results: Gels were formulated with Ag nanoparticles, Ag oxynitrate and colloidal Ag and showed antimicrobial activity for concentrations ranging from 0.002 to 30%. Gels showed stability of their chemical components, and their physicochemical properties, including viscosity, organoleptic characteristics, homogeneity, pH and spreadability, were suitable for topical application. Conclusion: Ag-based gels show antimicrobial action proportional to concentration, with higher action against Gram-negative bacteria and physicochemical stability for oral and skin infection applications.

Antibacterial activity of barbatimão (Stryphnodendron adstringens) against periodontopathogens and cytotoxic effects on fibroblasts.

This in vitro study aimed to evaluate the growth-inhibitory effects against periodontal disease-causing bacteria and cytotoxic effects against mouse fibroblast cells of the Stryphnodendron adstringens (barbatimão) hydroalcoholic extract. The contents of phenols and tannins in the extract were determined. The growth-inhibitory activity of the barbatimão was evaluated by determining the minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC). The viability of fibroblast cells was analyzed using the 3-[4,5-dimethylthiazol-2-yl]-2,5-diphenyl-tetrazolium bromide assay at 24 and 48 h post-treatment. The MIC values of the extract against Prevotella intermedia, Porphyromonas gingivalis, and Fusobacterium nucleatum were 0.05, 0.125, and 2 mg mL-1, respectively, while the MBC values were 4, 2, and 2 mg mL-1, respectively. The viability rate of barbatimão (0.25 mg mL-1)-treated L929 cells was higher than that of chlorhexidine (0.12%)-treated L929 cells at 48 h post-treatment. The contents of total phenolics and total tannins in the extract were 837.39 ± 0.10 and 785.82 ± 0.14 mg of tannic acid equivalent per gram of the extract, respectively. These findings indicate that the barbatimão hydroalcoholic extract, which exerted potent growth-inhibitory effects against the test microbial species and low cytotoxic effects on fibroblasts, has potential applications in the development of novel mouthwash products.

In situ evaluation of microbial profile formed on Ti-6Al-4V additive manufacturing disks: 16S rRNA sequencing.

STATEMENT OF PROBLEM: Dental implants obtained by additive manufacturing may present changes in the microbiome formed. However, studies profiling the microbial communities formed on Ti-6Al-4V are lacking. PURPOSE: The purpose of this in situ study was to characterize the profile of the microbial communities formed on Ti-6Al-4V disks produced by additive manufacturing and machining. MATERIAL AND METHODS: Titanium disks produced by additive manufacturing (AMD) and machining (UD) were housed in the buccal region of removable intraoral devices. These devices containing both disks were used by eight participants for 96 hours. After every 24 hours of intraoral exposure, the biofilm that had formed on the disks was collected. The 16S rRNA genes from each specimen were amplified and sequenced with the Miseq Illumina instrument and analyzed. Total microbial quantification was evaluated by analysis of variance-type statistics using the nparLD package. The Wilcoxon test was used to evaluate alpha diversity (α=.05). RESULTS: A difference was found in the microbial communities formed on additively manufactured and machined disks, with a reduction in operational taxonomic units (OTUs) for the AMD group compared with the UD group. Firmicutes and Proteobacteria were the most abundant phyla. Of the 1256 genera sequenced, Streptococcus predominated on both disks. CONCLUSIONS: The microbiome of the biofilm formed on the Ti-6Al-4V disks was significantly influenced by the fabrication method. The AMD disks showed lower total microbial counts than the UD disks.

Incorporation of a ß-AgVO3 Semiconductor in Resin Cement: Evaluation of Mechanical Properties and Antibacterial Efficacy.

PURPOSE: This in vitro study aimed to investigate the effect of incorporating the semiconductor nanostructured silver vanadate decorated with silver nanoparticles (ß-AgVO3) in a dual-cure resin cement on the degree of conversion (DC), microhardness, roughness, color, adhesion properties before and after artificial aging, and antimicrobial efficacy. MATERIAL AND METHODS: Three test groups were established: control (without ß-AgVO3), with the incorporation of 2.5% and 5% (by weight) of ß-AgVO3 in dual-cure resin cement (Allcem, FGM). The degree of conversion was measured using Fourier transform infrared spectroscopy (FTIR). To evaluate roughness (n = 10), microhardness (n = 10), color (n = 10), and to perform agar disk diffusion (n = 8), disks of 6-mm diameter and 2-mm height were manufactured using the same concentrations. For the color and shear bond strength test (n = 6), orthodontic brackets (Morelli) were used, which were cemented to natural human enamel and evaluated before and after artificial aging via thermocycling at 5°C and 55°C for 1000 cycles. For color measurements, a portable spectrocolorimeter and the CIE-Lab method were used. Data were analyzed using Student's t-test, ANOVA, and Tukey's multiple comparisons with significance set at α = 0.05. RESULTS: Semiconductor incorporation did not influence the cements's DC. The incorporation of 2.5% and 5% of ß-AgVO3 resulted in a significant increase in Knoop microhardness and surface roughness. Significant changes were observed in the color of the specimens when the semiconductor was incorporated. Adhesion after aging remained within the clinically recommended values in all groups, and antimicrobial activity was observed against Staphylococcus aureus, Streptococcus mutans, and Enterococcus faecalis at both concentrations tested. CONCLUSION: It is suggested to incorporate the semiconductor ß-AgVO3 in the dual-cure resin cement at both concentrations. Moreover, the physical-mechanical properties remained satisfactory for the proposed application.

Dental mini-implant designs to support overdentures: Development, biomechanical evaluation, and 3D digital image correlation.

STATEMENT OF PROBLEM: Custom mini-implants are needed for edentulous patients with extensive mandibular deficiencies where endosteal placement is not possible. However, the best design for these mini-implants is unclear. PURPOSE: The purpose of this in vitro study was to develop 2 dental mini-implant designs to support mandibular overdentures and evaluate the effect of their geometries on primary stability and stress distribution. MATERIAL AND METHODS: Two mini-implant designs were developed with changes in the shape, size, and arrangement of threads and chamfers. The experimental mini-implants were made of Grade V titanium alloy (Ti-6Al-4V), (Ø2.0×10 mm) and submitted to a nanoscale surface treatment. Thirty mini-implants (n=10) were placed into fresh swine bones: experimental-threaded, experimental-helical, and a commercially available product model (Intra-Lock System) as the control. The biomechanical evaluations of the experimental mini-implants were compared with those of the control in terms of primary stability, through insertion torque (IT), and with the pullout test. The analysis of stress distribution was performed by using the method of 3D digital image correlation under 250-N axial load and 100-N oblique (30-degree angled model) load. The data were analyzed by ANOVA and the Tukey HSD test (α=.05). RESULTS: The IT and pullout test presented a statistically significant difference for all mini-implants (P<.05), with higher IT for the experimental-threaded and maximum pullout force for the control, followed by threaded (P=.001) and helical (P=.001). Regarding the 3D digital image correlation, a lower incidence of stress was found in the cervical third for all mini-implants. No statistically significant differences were found between the designs evaluated (P>.05). CONCLUSIONS: Comparing the experimental mini-implants with the commercially available control, the experimental-threaded model presented greater primary stability, and all mini-implants showed less stress in the cervical third.

Bacterial adhesion to biomaterials: What regulates this attachment? A review.

Bacterial attachment to biomaterials is of great interest to the medical and dental field due to its impact on dental implants, dental prostheses, and others, leading to the need to introduce methods for biofilm control and mitigation of infections. Biofilm adhesion is a multifactorial process and involves characteristics relevant to the bacterial cell as well as biological, chemical, and physical properties relative to the surface of biomaterials. Bacteria encountered different environmental conditions during their growth and developed interspecies communication strategies, as well as various mechanisms to detect the environment and facilitate survival, such as chemical sensors or physical detection mechanisms. However, the factors that govern microbial attachment to surfaces are not yet fully understood. In order to understand how bacteria interact with surfaces, as well as to characterize the physical-chemical properties of bacteria adhesins, and to determine their interrelation with the adhesion to the substrate, in recent years new techniques of atomic force microscopy (AFM) have been developed and helped by providing quantitative results. Thus, the purpose of this review is to gather current studies about the factors that regulate microbial adhesion to surfaces in order to offer a guide to studies to obtain technologies that provide an antimicrobial surface.

Incorporation of Hybrid Nanomaterial in Dental Porcelains: Antimicrobial, Chemical, and Mechanical Properties.

Biofilm formation on biomaterials is a challenge in the health area. Antimicrobial substances based on nanomaterials have been proposed to solve this problem. The aim was to incorporate nanostructured silver vanadate decorated with silver nanoparticles (ß-AgVO3) into dental porcelains (IPS Inline and Ex-3 Noritake), at concentrations of 2.5% and 5%, and evaluate the surface characteristics (by SEM/EDS), antimicrobial activity (against Streptococcus mutans, Streptococcus sobrinus, Aggregatibacter actinomycetemcomitans, and Pseudomonas aeruginosa), silver (Ag+) and vanadium (V4+/V5+) ions release, and mechanical properties (microhardness, roughness, and fracture toughness). The ß-AgVO3 incorporation did not alter the porcelain's components, reduced the S. mutans, S. sobrinus and A. actinomycetemcomitans viability, increased the fracture toughness of IPS Inline, the roughness for all groups, and did not affect the microhardness of the 5% group. Among all groups, IPS Inline 5% released more Ag+, and Ex-3 Noritake 2.5% released more V4+/V5+. It was concluded that the incorporation of ß-AgVO3 into dental porcelains promoted antimicrobial activity against S. mutans, S. sobrinus, and A. actinomycetemcomitans (preventing biofilm formation), caused a higher release of vanadium than silver ions, and an adequate mechanical behavior was observed. However, the incorporation of ß-AgVO3 did not reduce P. aeruginosa viability and increased the surface roughness of dental porcelains.

Cytotoxic and genotoxic effects in human gingival fibroblast and ions release of endodontic sealers incorporated with nanostructured silver vanadate.

The cytotoxic and genotoxic effects of commercial endodontic sealers (AH Plus, Sealer 26 and Endomethasone N) incorporated with nanostructured silver vanadate decorated with silver nanoparticles (AgVO3 - at concentrations 2.5, 5, and 10%) on human gingival fibroblast (HGF), and the silver (Ag+ ) and vanadium (V4+ /V5+ ) ions release were evaluated. Cytotoxicity, cell death, and genotoxicity tests were carried out with extract samples of 24-hr and 7-days. The release of Ag+ and V4+ /V5+ was evaluated. Cytotoxicity in HGF was caused by AH Plus (AP) with 5 and 10% of AgVO3 (83.84 and 67.49% cell viability, respectively) with 24-hr extract (p < 0.05), as well as all concentrations of AP with 7-days extract (p < 0.05 -AP 0% = 73.17%; AP 2.5% = 75.07%; AP 5% = 70.62%; AP 10% = 68.46% cell viability). The commercial sealers Sealer 26 (S26) and Endomethasone N (EN) were cytotoxic (p < 0.05 - S26 0% = 34.81%; EN 0% = 20.99% cell viability with 7-days extract). AP 10% with 7-days extract induced 32% apoptotic cells in HGF (p < 0.05). Genotoxic effect was not observed. The AP groups released more Ag+ , while S26 and EN released more V4+ /V5+ in 24 hr. The Ag+ can be cytotoxic. In conclusion, the cytotoxicity caused to HGF can be attributed by the commercial sealers and enhanced by incorporation of AgVO3 , was not observed genotoxic effect, and apoptosis was induced only by AH Plus 10% 7-days extract. Ag+ can influence cell viability.

Effect of saliva and beverages on the surface roughness and hardnessof acrylic resin modified with nanomaterial.

PURPOSE: To evaluate the surface roughness and hardness of thermopolymerized acrylic resin incorporated with nanostructured silver vanadate (AgVO3) subjected to saliva and beverages. METHODS: The 128 specimens (5×5×2 mm) were prepared in thermopolymerized acrylic resin, according to the AgVO3 concentrations (n=32): 0%, 2.5%, 5% and 10%. The roughness and hardness were analyzed before and after immersion in saliva, Coca-Cola, orange juice and red wine, for 12 and 24 days. 2-way ANOVA and Bonferroni test (α= 0.05) were performed. RESULTS: After 12 days, Coca-Cola caused the highest roughness increase in the 2.5% group. The 10% group with saliva presented a higher roughness increase (P= 0.009). The control presented a decrease in roughness when in beverages (P< 0.05). After 24 days, orange juice and Coca-Cola produced a higher decrease in roughness in the control group (P< 0.05). After 12 days, saliva and wine produced a higher decrease in hardness of the 2.5% group (P< 0.05). Coca-Cola produced a decrease in hardness and wine an increase in hardness in the group with 10% AgVO3 concentration (P< 0.05). After 24 days, the group with 2.5% presented the highest decrease in hardness (P< 0.05). The immersions produced decreased hardness in the acrylic resin. Initially, there was an increase in roughness, however, over time, it decreased. CLINICAL SIGNIFICANCE: The control of oral biofilm is fundamental for the maintenance of the patient's oral health; however the incorporation of antimicrobial nanomaterial into prosthetic materials frequently exposed to saliva and beverages in the oral cavity interfered with the physical-mechanical properties of the products tested.

Influence of surface treatment on the fluorescence of composite resins subjected to in situ bleaching.

OBJECTIVE: Use fluorescence analysis to evaluate the effect of polishing and surface sealant on the color of composite resin bleached with carbamide peroxide and subjected to staining. MATERIALS AND METHODS: Forty-eight composite resin specimens (Z250/Z350XT) were fabricated. After 24 hours stored in distilled water, all specimens were submitted to in situ bleaching with 16% home peroxide for 8 hours daily for a period of 14 days. Subsequently specimens were separated in three groups according to surface treatment proposed (group 1-polishing Sof-Lex; group 2-BisCover; group 3-control). After this, all the specimens were stained with red wine. A spectrofluorometer was used to evaluate the fluorescence in two readouts (L0-after surface treatment and L1-after staining).Data were analyzed by applying ANOVA using a statistical software program. RESULTS: No differences were shown for the factor treatment and other interactions. The lowest mean fluorescence value was found for Z350XT resin (1759.18 ± 0.13) when compared with Z250 (6863.92 ± 0.13). There was significant difference in the mean fluorescence values for all surface treatments between the two different readouts L0 (4820.93 ± 0.05) and L1 (3802.17 ± 0.05). CONCLUSION: The results suggested that all surface treatments proposed did not influenced the results of wine staining of bleached resins when compared with the control evaluated by the fluorescence method. CLINICAL SIGNIFICANCE: The purposes of this research was to find solutions, by means of surfaces treatment, to achieve restorations with a satisfactory and similar final aspect in relation to the teeth, and avoid discrepancies related to the esthetics and longevity of the restoration.

Influence of AgVO3 incorporation on antimicrobial properties, hardness, roughness and adhesion of a soft denture liner.

The objective of this in vitro study was to investigate the effect of nanostructured silver vanadate decorated with silver nanoparticles (AgVO3) on antimicrobial activity, hardness, roughness, and adhesion of a soft denture liner. The antimicrobial efficacy of the Trusoft (Boswoth) liner incorporated with different concentrations of AgVO3 against Enterococcus faecalis, Pseudomonas aeruginosa, Candida albicans, and Staphyloccocus aureus (n = 5) was evaluated by the agar diffusion method. Roughness, hardness, and adhesion properties were also evaluated. The data were analyzed by analysis of variance (ANOVA) and Tukey's multiple comparison test with significance at the p < 0.05 level. At concentrations of 1 and 2.5%, AgVO3 incorporation was effective only against E. faecalis, and at 5 and 10%, against E. faecalis, P. aeruginosa, and C. albicans. None of the concentrations was effective against S. aureus. A decrease in hardness was found for the 1, 2.5, and 10% AgVO3 concentrations (p < 0.001) and at 5%, hardness was not affected. None of the concentrations affected the roughness of the material. A significant increase in tensile values was observed between the liner and heat-curing acrylic resin for 2.5% (p < 0.001) and 10% (p = 0.042) concentrations. AgVO3 incorporation to a soft denture liner promoted antimicrobial activity against E. faecalis, P. aeruginosa, and C. albicans without affecting roughness, maintaining the hardness properties recommended for soft and extra soft liners, and improving the adhesion between the liner and the acrylic resin used for dentures.

Development of an Impression Material with Antimicrobial Properties for Dental Application.

PURPOSE: To evaluate the antimicrobial activity and physico-mechanical properties of an irreversible hydrocolloid in which nanostructured silver vanadate decorated with silver nanoparticles (AgVO3 ) was added at various concentrations (0% - control, 2.5%, 5%, and 10% by weight). MATERIALS AND METHODS: The agar diffusion method (n = 10) was used to evaluate the inhibitory effect on the following species: Streptococcus mutans, Staphyloccocus aureus, Pseudomonas aeruginosa, Escherichia coli, and Candida albicans. The gelation time, flow capacity and plastic deformation were verified (n = 10). The data were analyzed using the Kruskal-Wallis test followed by the Dunn post-test, or via one-way ANOVA with multiple comparisons with a Bonferroni adjustment depending on the distribution (α = 0.05). RESULTS: All percentages of the nanomaterial were able to promote the antimicrobial activity of a hydrocolloid, with the formation of an inhibition zone (p < 0.05). In general, there was a dose-dependent effect on antimicrobial activity: higher concentrations of the nanomaterial promoted greater action except in the cases of P. aeruginosa (p < 0.001; F = 51.74) and S. aureus (p < 0.001), where the highest inhibition was for the 2.5% group. No difference was found in the gelation time when the control was compared with the groups with AgVO3 (p > 0.05). The difference was between the 5% and 10% groups (p = 0.007), and the latter promoted an increase in time. The flow capacity of the hydrocolloid with 5% of AgVO3 was significantly lower when compared with the control (p = 0.034). The AgVO3 influenced the plastic deformation (p < 0.001) in such a way that concentrations of 5% (p = 0.010) and 10% (p < 0.001) promoted an increase in this property when compared with the control. CONCLUSIONS: AgVO3 can be incorporated into an irreversible hydrocolloid as an antimicrobial agent without promoting adverse effects on physical-mechanical properties when used in concentrations of 2.5%.

Fabrication of dental implants by the additive manufacturing method: A systematic review.

STATEMENT OF PROBLEM: Placement of dental implants depends, among other factors, on anatomic conditions such as sufficient bone height and thickness. Thus, individualized dental implants seem to offer benefits for patients with alveolar bone resorption. Additive manufacturing has allowed for the fabrication of custom implants with microscale resolution and, although the efficiency of the process is unclear, is a potential process for manufacturing dental implants. PURPOSE: The purpose of this systematic review was to evaluate the current situation of additive manufacturing techniques for fabricating dental implants. MATERIAL AND METHODS: An electronic search was performed in the databases PubMed, Lilacs, Cochrane Library, and Science Direct, with the terms "additive manufacturing" AND "dental implants," "rapid prototyping" AND "dental implants," "3 D printing" AND "dental implants," "electron beam melting" AND "dental implants," "selective laser melting" AND "dental implants." The articles were screened, and the final selection of articles was obtained by using the inclusion and exclusion criteria. RESULTS: The database search resulted in 1322 articles, which were screened for title and/or summary according to the inclusion criteria. From the selected 38 articles, 30 remained after applying the exclusion criteria. These were read completely, resulting in a selection of 13 articles for this systematic review. Owing to the great variety of articles with different objectives, the results were based on a descriptive analysis of the following topics: additive manufacturing technique and material, printed structure and implant design, implant characteristics, mechanical analysis, surface treatment, and osseointegration. CONCLUSIONS: Additive manufacturing is a new technology that may solve many problems in diverse fields. In dentistry, however, further studies are needed to improve the method for manufacturing custom dental implants because no standard methodology is available. Moreover, the advantages and disadvantages of the process are not yet clearly defined.

Denture Liners: A Systematic Review Relative to Adhesion and Mechanical Properties.

PURPOSE: The objective of this systematic review is to compare results concerning the properties of adhesion, roughness, and hardness of dental liners obtained in the last ten years. METHODS: Searches on the databases LILACS, PubMed/Medline, Web of Science, and Cochrane Database of Systematic Reviews were supplemented with manual searches conducted between February and April of 2018. The inclusion criteria included experimental in vitro and in vivo, clinical, and laboratory studies on resilient and/or hard liners, assessment of hardness, roughness, and/or adhesion to the denture base, and physical/mechanical changes resulting from the disinfection process and changes in liners' composition or application. RESULTS: A total of 406 articles were identified and, from those, 44 are discussed. Twenty-four studies examined the bond strength, 13 surface roughness, and 19 the hardness. Of these 44 studies, 12 evaluated more than one property. Different substances were used in the attempt to improve adhesion. Considering roughness and hardness, the benefits of sealants have been tested, and the changes resulting from antimicrobial agents' incorporation have been assessed. CONCLUSION: Adhesion to the prosthesis base is improved with surface treatments. Rough surfaces and changes in hardness compromise the material's serviceability.

Retention force and deformation of an innovative attachment model for mini-implant-retained overdentures.

STATEMENT OF PROBLEM: The gradual loss of retention and the need for periodic replacement of attachment-system components are the most frequent complications in implant-supported overdentures. PURPOSE: The purpose of this in vitro study was to develop a new attachment system for overdentures with polymeric materials and compare its retention and deformation with a conventional O-ring attachment system. MATERIAL AND METHODS: A matrix with 2 mini-implants with ball abutments was used to simulate the mandibular border during a fatigue resistance test. A total of 60 polyacetal (n=20), polytetrafluoroethylene (n=20), and conventional O-ring (n=20) attachments were captured in pairs with acrylic resin and subjected to 3625 insertion and removal cycles, simulating 30 months of overdenture use. The internal and external deformations of the attachments were assessed using an optical stereomicroscope. One-way ANOVA and the Tukey honestly significant difference tests were used for statistical evaluation (α=.05). RESULTS: The polyacetal attachment system showed the highest retention (P<.001), followed by the O-ring and polytetrafluoroethylene attachments. The O-ring attachments exhibited the lowest deformation (P<.001), and the polyacetal attachments had the highest internal deformation (P<.001). CONCLUSIONS: The newly developed polyacetal attachment model increased the retention of mini-implant-retained overdentures, and despite the deformation experienced, the retention period appears to be better than that of conventional systems.

Effect of casting atmosphere on the marginal deficiency and misfit of Ni-Cr alloys with and without beryllium.

STATEMENT OF PROBLEM: The marginal adaptation of prosthetic crowns is still a significant clinical problem. PURPOSE: The purpose of this in vitro study was to evaluate the marginal deficiency and misfit of Ni-Cr alloys with and without beryllium under different casting conditions. MATERIAL AND METHODS: Four casting conditions were selected: flame-torch, induction/argon, induction/vacuum, and induction/air; and 2 alloys were used, Ni-Cr-Be and Ni-Cr. For each group, 10 metal specimens were prepared. Silicone indirect impressions and analysis of the degree of rounding were used to evaluate the marginal deficiencies of metal copings, and a standardized device for the setting pressure associated with optical microscopy was used to analyze the marginal misfit. Results were evaluated with 2-way ANOVA (α=.05), followed by the Tukey honest significant difference post hoc test, and the Pearson correlation test (α=.05). RESULTS: Alloy (P<.001) and casting technique (P<.001) were shown to affect marginal deficiencies. The Ni-Cr cast using the torch technique showed the highest marginal deficiency, and the Ni-Cr-Be cast in a controlled argon atmosphere showed the lowest (P<.001). Alloy (P=.472) and casting techniques (P=.206) did not affect the marginal misfit, but significant differences were found in the interaction (P=.001); the lowest misfit was achieved using the Ni-Cr-Be, and the highest misfit occurred with the molten Ni-Cr, using the cast torch technique. No correlation was found between deficiency and marginal misfit (r=.04, P=.69). CONCLUSIONS: The interactions demonstrated that the alloy containing beryllium that was cast in an argon atmosphere led to reduced marginal deficiency. Improved marginal adaptation can be achieved for the same alloy by using the torch technique.

Evaluation of antibiofilm and mechanical properties of new nanocomposites based on acrylic resins and silver vanadate nanoparticles.

OBJECTIVE: The purpose of this study was evaluate, for the first time, the impact of incorporation of nanostructured silver vanadate (ß-AgVO3) in antibiofilm and mechanical properties of dental acrylic resins (poly(methyl methacrylate), PMMA). DESIGN: The ß-AgVO3 was synthesized and characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy, and microanalysis (SEM/EDS). Resins specimens were prepared with 0-10% wt.% ß-AgVO3 and characterized by SEM, XRD and optical microscopy. The antibiofim activity of the samples against Candida albicans and Streptococcus mutans was investigated by XTT reduction test, colony-forming units (CFUs), and confocal laser scanning microscopy (CLSM). The flexural strength, hardness, and surface roughness of the samples containing ß-AgVO3 were compared with the pure PMMA matrix. RESULTS: The incorporation of 10% ß-AgVO3 significantly reduced the metabolic activity of C. albicans and S. mutans (p<0.05). There was a reduction in microbial load (CFU/mL) of microorganisms for the different concentrations used (p<0.05), which was confirmed by confocal microscopy. The addition of ß-AgVO3 did not change the mechanical properties of hardness and surface roughness of the resins (p>0.05). However, flexural strength decreased with the addition of amounts greater than 1% (p<0.05). CONCLUSIONS: ß-AgVO3 additions in dental acrylic resin may have an impact on inhibition of biofilm of main microorganisms associated with dental prostheses. However, the viability of clinical use should be evaluated in function of changed promoted in some mechanical properties.

In vitro study of the antibacterial properties and impact strength of dental acrylic resins modified with a nanomaterial.

STATEMENT OF PROBLEM: The accumulation of bacteria on the surface of dental prostheses can lead to systemic disease. PURPOSE: The purpose of this in vitro study was to evaluate the growth of Staphylococcus aureus and Pseudomonas aeruginosa on the surface of autopolymerizing (AP) and heat-polymerizing (HP) acrylic resins incorporated with nanostructured silver vanadate (ß-AgVO3) and its impact strength. MATERIAL AND METHODS: For each resin, 216 circular specimens (9 × 2 mm) were prepared for microbiologic analysis and 60 rectangular specimens (65 × 10 × 3.3 mm) for mechanical analysis, according to the percentage of ß-AgVO3: 0%, control group; 0.5%; 1%; 2.5%; 5%; and 10%. After a biofilm had formed, the metabolic activity of the bacteria was measured using the XTT reduction assay (2,3-bis-(2-methoxy-4-nitro-5-sulfophenyl)-2H-tetrazolium-5-carboxanilide) (n=8), and the number of viable cells was determined by counting colony forming units per milliliter (CFU/mL) (n=8). Confocal laser scanning microscopy (CLSM) was used to complement the analyses (n=2). The mechanical behavior was evaluated by impact strength assays (n=10). Data were analyzed by 2-way ANOVA, followed by the Tukey honestly significant difference (HSD) post hoc test (α=.05). RESULTS: The addition of 5% and 10% ß-AgVO3 significantly decreased the metabolic activity of P. aeruginosa for both resins (P<.05). The HP resin promoted a greater reduction in metabolic activity than the AP resin (P<.05). No difference was found in the metabolic activity of S. aureus according to the XTT (P>.05). The number of CFU/mL for S. aureus and P. aeruginosa decreased significantly when 5% and 10% ß-AgVO3 were added (P<.001). These concentrations significantly reduced the impact strength of the resins (P<.001) because the system was weakened by the presence of clusters of ß-AgVO3. CONCLUSION: The addition of ß-AgVO3 can provide acrylic resins with antibacterial activity but reduces their impact strength. More efficient addition methods should be investigated.