From radial to unidirectional water pumping in zeta-potential modulated Nafion nanostructures.

Chemically propelled micropumps are promising wireless systems to autonomously drive fluid flows for many applications. However, many of these systems are activated by nocuous chemical fuels, cannot operate at high salt concentrations, or have difficulty for controlling flow directionality. In this work we report on a self-driven polymer micropump fueled by salt which can trigger both radial and unidirectional fluid flows. The micropump is based on the cation-exchanger Nafion, which produces chemical gradients and local electric fields capable to trigger interfacial electroosmotic flows. Unidirectional pumping is predicted by simulations and achieved experimentally by nanostructuring Nafion into microarrays with a fine tune modulation of surrounding surface zeta potentials. Nafion micropumps work in a wide range of salt concentrations, are reusable, and can be fueled by different salt cations. We demonstrate that they work with the common water-contaminant cadmium, using the own capture of this ion as fuel to drive fluid pumping. Thus, this system has potential for efficient and fast water purification strategies for environmental remediation. Unidirectional Nafion pumps also hold promise for effective analyte delivery or preconcentration for (bio)sensing assays.

3D-PLA-experimental set up to display the electrical background of the so-called geometric factor of electrokinetic cells.

The so-called geometric factor defined in electrokinetic cells, L/S (L being the length and S the cross-section of the channel), is relevant for providing the surface interaction electrical potential (zeta potential, ζ) of large surfaces, such as those used in the design of biomedical devices or water purification systems. Conversely, recent studies demonstrate that this factor is also employed to determine geometrical parameters, such as porosity in membrane-like systems. This factor, which has been attributed exclusively a geometrical character, can also be obtained from the electrical conductivity and resistance of the electrokinetic channel. In this work, we assess whether these two ways of obtaining the L/S factor are equivalent and how possible deviations can affect the value of the zeta potential. For this purpose, we work with channels of different geometries obtained by 3D printing using PLA (polylactic acid) as a polymer employed in biomedical applications. The discrepancies between the L/S factor obtained by electrical and purely geometrical measurements increase as the geometrical L/S factor becomes larger, reaching differences close to 80%. The results show that the so-called geometrical L/S factor also has an important electrical contribution and would be better denoted as electrogeometric factor. The differences found between the L/S factors are also propagated to the calculation of ζ but an optimum conductivity zone (from about 10 to 40 mS m-1) can be defined to obtain the zeta potential by selecting any of the L/S factors obtained from electrokinetic measurements. The results of this work should be taken into account in those investigations that use the L/S factor to obtain the geometry-porosity of permeable materials.

Impact of PLA/Mg films degradation on surface physical properties and biofilm survival.

New biocompatible and bioabsorbable materials are currently being developed for bone regeneration. These serve as scaffolding for controlled drug release and prevent bacterial infections. Films of polylactic acid (PLA) polymers that are Mg-reinforced have demonstrated they have suitable properties and bioactive behavior for promoting the osseointegration process. However little attention has been paid to studying whether the degradation process can alter the adhesive physical properties of the biodegradable film and whether this can modify the biofilm formation capacity of pathogens. Moreover, considering that the concentration of Mg and other corrosion products may not be constant during the degradation process, the question that arises is whether these changes can have negative consequences in terms of the bacterial colonization of surfaces. Bacteria are able to react differently to the same compound, depending on its concentration in the medium and can even become stronger when threatened. In this context, physical surface parameters such as hydrophobicity, surface tension and zeta potential of PLA films reinforced with 10% Mg have been determined before and after degradation, as well as the biofilm formation capacity of Staphylococcus epidermidis. The addition of Mg to the films makes them less hydrophobic and the degradation also reduces the hydrophobicity and increases the negative charge of the surface, especially over long periods of time. Early biofilm formation at 8 h is consistent with the physical properties of the films, where we can observe a reduction in the bacterial biofilm formation. However, after 24 h of incubation, the biofilm formation increases significantly on the PLA/Mg films with respect to PLA control. The explosive release of Mg ions and other corrosion products within the first hours were not enough to prevent a greater biofilm formation after this initial time. Consequently, the Mg addition to the polymer matrix had a bacteriostatic effect but not a bactericidal one. Future works should aim to optimize the design and biofunctionality of these promising bioabsorbable composites for a degradation period suitable for the intended application.