Chemical and Electrochemical Characterization of Hot-Pressed Li6PS5Cl Solid State Electrolyte: Operating Pressure-Invariant High Ionic Conductivity.

Sulfide solid state electrolytes (SSE) are among the most promising materials in the effort to replace liquid electrolytes, largely due to their comparable ionic conductivities. Among the sulfide SSEs, Argyrodites (Li6PS5X, X=Cl, Br, I) further stand out due to their high theoretical ionic conductivity (~1×10-2 S cm-1) and interfacial stability against reactive metal anodes such as lithium. Generally, solid state electrolyte pellets are pressed from powder feedstock at room temperature, however, pellets fabricated by cold pressing consistently result in low bulk density and high porosity, facilitating interfacial degradation reactions and allowing dendrites to propagate through the pores and grain boundaries. Here, we demonstrate the mechanical and electrochemical implications of hot-pressing standalone LPSCl SSE pellets with near-theoretical ionic conductivity, superior cycling performance, and enhanced mechanical stability. X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and x-ray diffraction spectroscopy (XRD) analysis reveal no chemical changes to the Argyrodite surface after hot pressing up to 250 °C. Moreover, we use electrochemical impedance spectroscopy (EIS) to understand mechanical stability of Argyrodite SSE pellets as a function of externally applied pressure, demonstrating for the first time pressed standalone Argyrodite pellets with near-theoretical conductivities at external pressures below 14 MPa.

In Situ Raman Mapping of Si Island Electrodes and Stress Modeling as a Function of Lithiation and Size.

Si is known for cracking and delamination during electrochemical cycling of a battery due to the large volume change associated with Li insertion and extraction. However, it has been found experimentally that patterned Si island electrodes that are 200 nm thick and less than 7 µm wide can deform in a purely elastic manner. Inspired by this, we performed in situ Raman stress characterization of model poly-crystalline Si island electrodes using an electrochemical cell coupled with an immersion objective lens and designed for a short working distance. A 5 µm wide Si island electrode showed a parabolic stress profile during lithiation, while for a 15 µm Si island electrode, a stress plateau in the center of the electrode was observed. A continuum model with coupled electro-chemo-mechanical (ECM) physics was established to understand the stress measurement. A qualitative agreement was reached between modeling and experimental data, and the critical size effect could be explained by the Li diffusive flux as governed by competition between the Li concentration and hydrostatic stress gradients. Below the critical size, the stress gradient drives Li toward the edges, where the electrode volume is free to expand, while above the critical size, the stress plateau inhibits Li diffusion to the edge and forces destructive stress relief by cracking. This work represents a promising methodology for in situ characterization of ECM coupling in battery electrodes, with suggestions provided for further improvement.

Dynamic Electrode-Electrolyte Intermixing in Solid-State Sodium Nano-Batteries.

Nanostructured solid-state batteries (SSBs) are poised to meet the demands of next-generation energy storage technologies by realizing performance competitive to their liquid-based counterparts while simultaneously offering improved safety and expanded form factors. Atomic layer deposition (ALD) is among the tools essential to fabricate nanostructured devices with challenging aspect ratios. Here, we report the fabrication and electrochemical testing of the first nanoscale sodium all-solid-state battery (SSB) using ALD to deposit both the V2O5 cathode and NaPON solid electrolyte followed by evaporation of a thin-film Na metal anode. NaPON exhibits remarkable stability against evaporated Na metal, showing no electrolyte breakdown or significant interphase formation in the voltage range of 0.05-6.0 V vs Na/Na+. Electrochemical analysis of the SSB suggests intermixing of the NaPON/V2O5 layers during fabrication, which we investigate in three ways: in situ spectroscopic ellipsometry, time-resolved X-ray photoelectron spectroscopy (XPS) depth profiling, and cross-sectional cryo-scanning transmission electron microscopy (cryo-STEM) coupled with electron energy loss spectroscopy (EELS). We characterize the interfacial reaction during the ALD NaPON deposition on V2O5 to be twofold: (1) reduction of V2O5 to VO2 and (2) Na+ insertion into VO2 to form NaxVO2. Despite the intermixing of NaPON-V2O5, we demonstrate that NaPON-coated V2O5 electrodes display enhanced electrochemical cycling stability in liquid-electrolyte coin cells through the formation of a stable electrolyte interphase. In all-SSBs, the Na metal evaporation process is found to intensify the intermixing reaction, resulting in the irreversible formation of mixed interphases between discrete battery layers. Despite this graded composition, the SSB can operate for over 100 charge-discharge cycles at room temperature and represents the first demonstration of a functional thin-film solid-state sodium-ion battery.

Micro-Raman Stress Characterization of Crystalline Si as a Function of the Lithiation State.

This work presents a stress characterization of crystalline Si electrodes using micro-Raman spectroscopy. First, the phase heterogeneity in the c-Si electrodes after initial lithiation was investigated by scanning electron microscopy (SEM) and other complementary techniques. A surprising three-phase layer structure, with a-LixSi (x = 2.5), c-LixSi (x = 0.3-2.5), and c-Si layers, was observed, and its origin was attributed to the electro-chemo-mechanical (ECM) coupling effect in the c-Si electrodes. Then, a Raman scan was performed to characterize stress distribution in lithiated c-Si electrodes. The results showed that the maximum tensile stress occurred at the interface between c-LixSi and c-Si layers, indicating a plastic flow behavior. The yield stress increased with total lithium charge, and the relationship showed consistency with a prior multibeam optical sensor (MOS) study. Lastly, stress distribution and structural integrity of the c-Si electrodes after initial delithiation and further cycling were studied, and a comprehensive picture of the failure mechanism of the c-Si electrode was obtained.

Bacterial chemotaxis in static gradients quantified in a biopolymer membrane-integrated microfluidic platform.

Chemotaxis is a fundamental bacterial response mechanism to changes in chemical gradients of specific molecules known as chemoattractant or chemorepellent. The advancement of biological platforms for bacterial chemotaxis research is of significant interest for a wide range of biological and environmental studies. Many microfluidic devices have been developed for its study, but challenges still remain that can obscure analysis. For example, cell migration can be compromised by flow-induced shear stress, and bacterial motility can be impaired by nonspecific cell adhesion to microchannels. Also, devices can be complicated, expensive, and hard to assemble. We address these issues with a three-channel microfluidic platform integrated with natural biopolymer membranes that are assembled in situ. This provides several unique attributes. First, a static, steady and robust chemoattractant gradient was generated and maintained. Second, because the assembly incorporates assembly pillars, the assembled membrane arrays connecting nearby pillars can be created longer than the viewing window, enabling a wide 2D area for study. Third, the in situ assembled biopolymer membranes minimize pressure and/or chemiosmotic gradients that could induce flow and obscure chemotaxis study. Finally, nonspecific cell adhesion is avoided by priming the polydimethylsiloxane (PDMS) microchannel surfaces with Pluronic F-127. We demonstrated chemotactic migration of Escherichia coli as well as Pseudomonas aeruginosa under well-controlled easy-to-assemble glucose gradients. We characterized motility using the chemotaxis partition coefficient (CPC) and chemotaxis migration coefficient (CMC) and found our results consistent with other reports. Further, random walk trajectories of individual cells in simple bright field images were conveniently tracked and presented in rose plots. Velocities were calculated, again in agreement with previous literature. We believe the biopolymer membrane-integrated platform represents a facile and convenient system for robust quantitative assessment of cellular motility in response to various chemical cues.

Nanoscale Li, Na, and K ion-conducting polyphosphazenes by atomic layer deposition.

A key trailblazer in the development of thin-film solid-state electrolytes has been lithium phosphorous oxynitride (LiPON), the success of which has led to recent progress in thin-film ion conductors. Here we compare the structural, electrochemical, and processing parameters between previously published LiPON and NaPON ALD processes with a novel ALD process for the K analogue potassium phosphorous oxynitride (KPON). In each ALD process, alkali tert-butoxides and diethylphosphoramidate are used as precursors. To understand the ALD surface reactions, this work proposes a reaction mechanism determined by in-operando mass spectrometry for the LiPON process as key to understanding the characteristics of the APON (A = Li, Na, K) family. As expected, NaPON and LiPON share similar reaction mechanisms as their structures are strikingly similar. KPON, however, exhibits similar ALD process parameters but the resulting film composition is quite different, showing little nitrogen incorporation and more closely resembling a phosphate glass. Due to the profound difference in structure, KPON likely undergoes an entirely different reaction mechanism. This paper presents a comprehensive summary of ALD ion conducting APON films as well as a perspective that highlights the versatility of ALD chemistries as a tool for the development of novel thin film ion-conductors.

Atomic Layer Deposition of Sodium Phosphorus Oxynitride: A Conformal Solid-State Sodium-Ion Conductor.

The development of novel materials that are compatible with nanostructured architectures is required to meet the demands of next-generation energy-storage technologies. Atomic layer deposition (ALD) allows for the precise synthesis of new materials that can conformally coat complex 3D structures. In this work, we demonstrate a thermal ALD process for sodium phosphorus oxynitride (NaPON), a thin-film solid-state electrolyte (SSE), for sodium-ion batteries (SIBs). NaPON is analogous to the commonly used lithium phosphorus oxynitride SSE in lithium-ion batteries. The ALD process produces a conformal film with a stoichiometry of Na4PO3N, corresponding to a sodium polyphosphazene structure. The electrochemical properties of NaPON are characterized to evaluate its potential in SIBs. The NaPON film exhibited a high ionic conductivity of 1.0 × 10-7 S/cm at 25 °C and up to 2.5 × 10-6 S/cm at 80 °C, with an activation energy of 0.53 eV. In addition, the ionic conductivity is comparable and even higher than the ionic conductivities of ALD-fabricated Li+ conductors. This promising result makes NaPON a viable SSE or passivation layer in solid-state SIBs.

Mg2+ ion-catalyzed polymerization of 1,3-dioxolane in battery electrolytes.

Electrolyte salts with Mg2+ and Al3+ Lewis acidic cations demonstrate polymerization of 1,3-dioxolane. The speed and extent of the reaction depends on coordination of the anion with the Mg2+ cation catalyst. Weakly coordinating anions such as TFSI- aid faster polymerization while strongly coordinating anions such as ClO4- hinder the polymerization.

Enhancing Lithium Insertion with Electrostatic Nanoconfinement in a Lithography Patterned Precision Cell.

The rapidly growing demand for portable electronics, electric vehicles, and grid storage drives the pursuit of high-performance electrical energy storage (EES). A key strategy for improving EES performance is exploiting nanostructured electrodes that present nanoconfined environments of adjacent electrolytes, with the goal to decrease ion diffusion paths and increase active surface areas. However, fundamental gaps persist in understanding the interface-governed electrochemistry in such nanoconfined geometries, in part because of the imprecise and variable dimension control. Here, we report quantification of lithium insertion under nanoconfinement of the electrolyte in a precise lithography-patterned nanofluidic cell. We show a mechanism that enhances ion insertion under nanoconfinement, namely, selective ion accumulation when the confinement length is comparable to the electrical double layer thickness. The nanofabrication approach with uniform and accurate dimensional control provides a versatile model system to explore fundamental mechanisms of nanoscale electrochemistry, which could have an impact on practical energy storage systems.

Impact of pore size, interconnections, and dynamic conductivity on the electrochemistry of vanadium pentoxide in well defined porous structures.

Considering the tortuous, random porous nanostructures existing in many battery electrodes, it is essential to understand electronic and ionic behaviors in such a confined nanoscale porous geometry in which electron and ion transports can change dynamically. Here, we have carefully designed three dimensional (3D) interconnected porous electrode structures and performed experiments to probe how the ion and electron transport is impacted within these controlled geometries. By using anodized aluminum oxide as a template, we were able to fabricate both 1D array electrodes and 3D electrodes with varying numbers of interconnections, utilizing vanadium oxide (V2O5) as the active material. We demonstrate that the inherent properties of the electrode material in combination with the structural properties of the electrodes can both positively and negatively impact electrochemical characteristics. Most notably, electrodes with seven interconnecting layers in their structure had 19.7% less capacity at 25C than electrodes with zero interconnecting layers, demonstrating the negative effect of interconnections combined with poor electronic conductivity of V2O5 upon lithiation beyond one Li insertion. These results indicate that a careful consideration of the material and structural properties is needed for the design of high performance battery systems.

Electrochemically Controlled Solid Electrolyte Interphase Layers Enable Superior Li-S Batteries.

Lithium-sulfur (Li-S) batteries suffer from shuttle reactions during electrochemical cycling, which cause the loss of active material sulfur from sulfur-carbon cathodes, and simultaneously incur the corrosion and degradation of the lithium metal anode by forming passivation layers on its surface. These unwanted reactions therefore lead to the fast failure of batteries. The preservation of the highly reactive lithium metal anode in sulfur-containing electrolytes has been one of the main challenges for Li-S batteries. In this study, we systematically controlled and optimized the formation of a smooth and uniform solid electrolyte interphase (SEI) layer through electrochemical pretreatment of the Li metal anode under controlled current densities. A distinct improvement of battery performance in terms of specific capacity and power capability was achieved in charge-discharge cycling for Li-S cells with pretreated Li anodes compared to pristine untreated ones. Importantly, at a higher power density (1 C rate, 3 mA cm-2), the Li-S cells with pretreated Li anodes protected by a controlled elastomer (Li-Protected-by-Elastomer, LPE)) show the suppression of the Li dendrite growth and exhibit 3-4 times higher specific capacity than the untreated ones after 100 electrochemical cycles. The formation of such a controlled uniform SEI was confirmed, and its surface chemistry, morphology, and electrochemical properties were characterized by X-ray photoelectron spectroscopy, focused-ion beam cross sectioning, and scanning electron microscopy. Adequate pretreatment current density and time are critical in order to form a continuous and uniform SEI, along with good Li-ion transport property.

Epitaxial Welding of Carbon Nanotube Networks for Aqueous Battery Current Collectors.

Carbon nanomaterials are desirable candidates for lightweight, highly conductive, and corrosion-resistant current collectors. However, a key obstacle is their weak interconnection between adjacent nanostructures, which renders orders of magnitude lower electrical conductivity and mechanical strength in the bulk assemblies. Here we report an "epitaxial welding" strategy to engineer carbon nanotubes (CNTs) into highly crystalline and interconnected structures. Solution-based polyacrylonitrile was conformally coated on CNTs as "nanoglue" to physically join CNTs into a network, followed by a rapid high-temperature annealing (>2800 K, overall ∼30 min) to graphitize the polymer coating into crystalline layers that also bridge the adjacent CNTs to form an interconnected structure. The contact-welded CNTs (W-CNTs) exhibit both a high conductivity (∼1500 S/cm) and a high tensile strength (∼120 MPa), which are 5 and 20 times higher than the unwelded CNTs, respectively. In addition, the W-CNTs display chemical and electrochemical stabilities in strong acidic/alkaline electrolytes (>6 mol/L) when potentiostatically stressing at both cathodic and anodic potentials. With these exceptional properties, the W-CNT films are optimal as high-performance current collectors and were demonstrated in the state-of-the-art aqueous battery using a "water-in-salt" electrolyte.

Kinetics-Controlled Degradation Reactions at Crystalline LiPON/Lix CoO2 and Crystalline LiPON/Li-Metal Interfaces.

Detailed understanding of solid-solid interface structure-function relationships is critical for the improvement and wide deployment of all-solid-state batteries. The interfaces between lithium phosphorous oxynitride (LiPON) solid electrolyte material and lithium metal anode, and between LiPON and Lix CoO2 cathode, have been reported to generate solid-electrolyte interphase (SEI)-like products and/or disordered regions. Using electronic structure calculations and crystalline LiPON models, we predict that LiPON models with purely P-N-P backbones are kinetically inert towards lithium at room temperature. In contrast, transfer of oxygen atoms from low-energy Lix CoO2 (104) surfaces to LiPON is much faster under ambient conditions. The mechanisms of the primary reaction steps, LiPON structural motifs that readily reacts with lithium metal, experimental results on amorphous LiPON to partially corroborate these predictions, and possible mitigation strategies to reduce degradations are discussed. LiPON interfaces are found to be useful case studies for highlighting the importance of kinetics-controlled processes during battery assembly at moderate processing temperatures.

Three-Dimensional Solid-State Lithium-Ion Batteries Fabricated by Conformal Vapor-Phase Chemistry.

Three-dimensional thin-film solid-state batteries (3D TSSB) were proposed by Long et al. in 2004 as a structure-based approach to simultaneously increase energy and power densities. Here, we report experimental realization of fully conformal 3D TSSBs, demonstrating the simultaneous power-and-energy benefits of 3D structuring. All active battery components-electrodes, solid electrolyte, and current collectors-were deposited by atomic layer deposition (ALD) onto standard CMOS processable silicon wafers microfabricated to form arrays of deep pores with aspect ratios up to approximately 10. The cells utilize an electrochemically prelithiated LiV2O5 cathode, a very thin (40-100 nm) Li2PO2N solid electrolyte, and a SnN x anode. The fabrication process occurs entirely at or below 250 °C, promising compatibility with a variety of substrates as well as integrated circuits. The multilayer battery structure enabled all-ALD solid-state cells to deliver 37 µAh/cm2·µm (normalized to cathode thickness) with only 0.02% per-cycle capacity loss. Conformal fabrication of full cells over 3D substrates increased the areal discharge capacity by an order of magnitude while simulteneously improving power performance, a trend consistent with a finite element model. This work shows that the exceptional conformality of ALD, combined with conventional semiconductor fabrication methods, provides an avenue for the successful realization of long-sought 3D TSSBs which provide power performance scaling in regimes inaccessible to planar form factor cells.

Investigation of the water-stimulated Mg2+ insertion mechanism in an electrodeposited MnO2 cathode using X-ray photoelectron spectroscopy.

Batteries based on magnesium chemistry are being widely investigated as an alternative energy storage system to replace lithium-ion batteries. Mg batteries have multiple challenges, especially on the cathode side. The divalent Mg ion has slow insertion kinetics in many metal oxide cathodes conventionally used in Li-ion batteries. One solution that has been explored is adding water molecules into an organic electrolyte, which has been shown to aid in Mg insertion and improve performance of manganese oxide (MnO2) cathodes. While there have been studies on Mg insertion mechanisms into MnO2 in solely aqueous or organic electrolytes for some crystalline MnO2 polymorphs, our work is focused on water-containing organic electrolyte, where an H2O to Mg ratio of 6 : 1 is present. In this study, we report results based on ex situ XPS experiments, including both angle resolved and depth profiling studies to assess the surface reactions and determine the mechanism of Mg insertion into an amorphous, electrodeposited MnO2 cathode. We propose that in this mixed electrolyte system, there is a combined insertion/conversion reaction mechanism whereby Mg and H2O molecules co-insert into the MnO2 structure and a reaction between H2O and Mg creates an observable Mg(OH)2 layer at the surface of the MnO2. A more full understanding of the role of the water molecules is important to aid in the future design of cathode materials, especially when determining potential ways to integrate metal oxides in Mg batteries.

Nanoscale Protection Layers To Mitigate Degradation in High-Energy Electrochemical Energy Storage Systems.

In the pursuit of energy storage devices with higher energy and power, new ion storage materials and high-voltage battery chemistries are of paramount importance. However, they invite-and often enhance-degradation mechanisms, which are reflected in capacity loss with charge/discharge cycling and sometimes in safety problems. Degradation mechanisms are often driven by fundamentals such as chemical and electrochemical reactions at electrode-electrolyte interfaces, volume expansion and stress associated with ion insertion and extraction, and profound inhomogeneity of electrochemical behavior. While it is important to identify and understand these mechanisms at some reasonable level, it is even more critical to design strategies to mitigate these degradation pathways and to develop means to implement and validate the strategies. A growing set of research highlights the mitigation benefits achievable by forming thin protection layers (PLs) intentionally created as artificial interphase regions at the electrode-electrolyte interface. These advances illustrate a promising-perhaps even generic-pathway for enabling higher-energy and higher-voltage battery configurations. In this Account, we summarize examples of such PLs that serve as mitigation strategies to avoid degradation in lithium metal anodes, conversion-type electrode materials, and alloy-type electrodes. Examples are chosen from a larger body of electrochemical degradation research carried out in Nanostructures for Electrical Energy Storage (NEES), our DOE Energy Frontier Research Center. Overall, we argue on the basis of experimental and theoretical evidence that PLs effectively stabilize the electrochemical interfaces to prevent parasitic chemical and electrochemical reactions and mitigate the structural, mechanical, and compositional degradation of the electrode materials at the electrode-electrolyte interfaces. The evidenced improvement in performance metrics is accomplished by (1) establishing a homogeneous interface for ion insertion and extraction, (2) providing mechanical constraints to maintain structural integrity and robust electronic and ionic conduction pathways, and (3) introducing spatial confinements on the electrode material matrix to alter the phase transformation (delaying the occurrence of the conversion reaction) upon Li insertion, which results in superior electrode performance, excellent capacity retention, and improved reversibility. Taken together, these examples portray a valuable role for thin protection layers synthesized over electrode surfaces, both for their benefit to cycle stability and for revealing insights into degradation and mitigation mechanisms. Furthermore, they underscore the impact of complex electrochemical behavior at nanoscale materials and nanostructure interfaces in modulating the behavior of energy storage devices at the mesoscale and macroscale.

High performance asymmetric V2O5-SnO2 nanopore battery by atomic layer deposition.

Here we report the high performance and cyclability of an asymmetric full cell nanopore battery, comprised of V2O5 as the cathode and prelithiated SnO2 as the anode, with integrated nanotubular Pt current collectors underneath each nanotubular storage electrode, confined within an anodized aluminium oxide (AAO) nanopore. Enabled by atomic layer deposition (ALD), this coaxial nanotube full cell is fully confined within a high aspect ratio nanopore (150 nm in diameter, 50 µm in length), with an ultra-small volume of about 1 fL. By controlling the amount of lithium ion prelithiated into the SnO2 anode, we can tune the full cell output voltage in the range of 0.3 V to 3 V. When tested as a massively parallel device (∼2 billion cm-2), this asymmetric nanopore battery array displays exceptional rate performance and cyclability: when cycled between 1 V and 3 V, capacity retention at the 200C rate is ∼73% of that at 1C, and at 25C rate only 2% capacity loss occurs after more than 500 charge/discharge cycles. With the increased full cell output potential, the asymmetric V2O5-SnO2 nanopore battery shows significantly improved energy and power density over the previously reported symmetric cell, 4.6 times higher volumetric energy and 5.2 times higher power density - an even more promising indication that controlled nanostructure designs employing nanoconfined environments with large electrode surface areas present promising directions for future battery technology.

Negating interfacial impedance in garnet-based solid-state Li metal batteries.

Garnet-type solid-state electrolytes have attracted extensive attention due to their high ionic conductivity, approaching 1 mS cm-1, excellent environmental stability, and wide electrochemical stability window, from lithium metal to ∼6 V. However, to date, there has been little success in the development of high-performance solid-state batteries using these exceptional materials, the major challenge being the high solid-solid interfacial impedance between the garnet electrolyte and electrode materials. In this work, we effectively address the large interfacial impedance between a lithium metal anode and the garnet electrolyte using ultrathin aluminium oxide (Al2O3) by atomic layer deposition. Li7La2.75Ca0.25Zr1.75Nb0.25O12 (LLCZN) is the garnet composition of choice in this work due to its reduced sintering temperature and increased lithium ion conductivity. A significant decrease of interfacial impedance, from 1,710 Ω cm2 to 1 Ω cm2, was observed at room temperature, effectively negating the lithium metal/garnet interfacial impedance. Experimental and computational results reveal that the oxide coating enables wetting of metallic lithium in contact with the garnet electrolyte surface and the lithiated-alumina interface allows effective lithium ion transport between the lithium metal anode and garnet electrolyte. We also demonstrate a working cell with a lithium metal anode, garnet electrolyte and a high-voltage cathode by applying the newly developed interface chemistry.

Perspectives in flow-based microfluidic gradient generators for characterizing bacterial chemotaxis.

Chemotaxis is a phenomenon which enables cells to sense concentrations of certain chemical species in their microenvironment and move towards chemically favorable regions. Recent advances in microbiology have engineered the chemotactic properties of bacteria to perform novel functions, but traditional methods of characterizing chemotaxis do not fully capture the associated cell motion, making it difficult to infer mechanisms that link the motion to the microbiology which induces it. Microfluidics offers a potential solution in the form of gradient generators. Many of the gradient generators studied to date for this application are flow-based, where a chemical species diffuses across the laminar flow interface between two solutions moving through a microchannel. Despite significant research efforts, flow-based gradient generators have achieved mixed success at accurately capturing the highly subtle chemotactic responses exhibited by bacteria. Here we present an analysis encompassing previously published versions of flow-based gradient generators, the theories that govern their gradient-generating properties, and new, more practical considerations that result from experimental factors. We conclude that flow-based gradient generators present a challenge inherent to their design in that the residence time and gradient decay must be finely balanced, and that this significantly narrows the window for reliable observation and quantification of chemotactic motion. This challenge is compounded by the effects of shear on an ellipsoidal bacterium that causes it to preferentially align with the direction of flow and subsequently suppresses the cross-flow chemotactic response. These problems suggest that a static, non-flowing gradient generator may be a more suitable platform for chemotaxis studies in the long run, despite posing greater difficulties in design and fabrication.

Interconnected mesoporous V2O5 electrode: impact on lithium ion insertion rate.

Here we introduce a strategy for creating nanotube array electrodes which feature periodic regions of porous interconnections providing open pathways between adjacent nanotubes within the array, utilizing a combination of anodized aluminum oxide growth modification (AAO) and atomic layer deposition. These porous interconnected structures can then be used as testbed electrodes to explore the influence of mesoscale structure on the electrochemical properties of the interconnected mesoporous electrodes. Critically, these unique structures allow the solid state lithium diffusion pathways to be held essentially constant, while the larger structure is modified. While it was anticipated that this strategy would simply provide increased mass loading, the kinetics of the Li+ ion insertion reaction in the porous interconnected electrodes are dramatically improved, demonstrating significantly better capacity retention at high rates than their aligned counterparts. We utilize a charge deconvolution method to explore the kinetics of the charge storage reactions. We are able to trace the origin of the structural influence on rate performance to electronic effects within the electrodes.