Post-fatigue fracture load, stress concentration and mechanical properties of feldspathic, leucite- and lithium disilicate-reinforced glass ceramics.

Objective: To evaluate the mechanical properties of different CAD/CAM ceramic systems and the post-fatigue fracture and stress distribution when used as cemented crowns. Materials and methods: Sixty (60) CAD/CAM monolithic crowns were milled using three different ceramic materials (FD - Feldspathic [Vita Mark II]), LE - Leucite-based ceramic [IPS Empress CAD] and LD - Lithium Disilicate [IPS e.max CAD]) and adhesively cemented on resin composite dyes. Specimens were stored in distillated water (37 °C) for 7 days. After, half of the crowns were submitted to immediate fracture load test while the other half was submitted to fatigue cycling. The average cement layer of approximately 80 µm was assessed using scanning electron microscopy (SEM). The average thickness was used in the three-dimensional (3D) Finite Element Analysis (FEA). For each ceramic material, the density, Poisson ratio, shear modulus, Young modulus, fracture toughness, and true hardness were assessed (n = 3). The data was used to assess the Maximum Principal Stress throughout 3D-FEA according to each material during load to fail and post-fatigue. Data were submitted to two-way ANOVA and Tukey test (α = 0.05). Results: LD showed the highest compression load, density, shear modulus, Young modulus, fracture toughness and true hardness values. While LE presented the lowest mechanical properties values. There is no difference in the Poisson ratio between the evaluated ceramics. Conclusion: LD was susceptible to aging process but presented stronger physicomechanical properties, showing the highest post-fatigue fracture load and highest stress magnitude.

Correlation between 2D and 3D measurements of cement space in CAD-CAM crowns.

STATEMENT OF PROBLEM: Although the 2D analysis of prosthesis cementation space has been popular, its correlation with volumetric comparison (3D data) of cement space is unclear. PURPOSE: The purpose of this in vitro study was to evaluate the cement space in computer-aided design and computer-aided manufacturing (CAD-CAM) crowns of different materials and correlate 2D measurements of cement space with their corresponding 3D values (volume of cement space) by using microcomputed tomography (µCT) analysis of regions of interest. MATERIAL AND METHODS: Ten molar crowns were milled in lithium disilicate (LD), resin nanoceramic (RN), and zirconia (Z) ceramics. Silicone replicas were produced and used as the analog cement layer and scanned with a desktop X-ray microfocus CT scanner. Twenty-eight slices were evaluated in 3 regions: marginal, axial, and occlusal (n=84 measurement points/specimen). After 3D reconstruction of the cement space, the volume was calculated. Data were statistically evaluated through 2-way ANOVA and Bonferroni test (α=.05). The Pearson correlation test was used to investigate the correlation between the 2D and 3D data. RESULTS: The volumes of the occlusal (LD 10 ±1 mm3; RN 9 ±1 mm3) and axial regions (LD 9 ±2 mm3; RN 8 ±1 mm3) were significantly higher than the volume of the marginal region for LD and RN specimens (LD 6 ±2 mm3; RN 4 ±1 mm3) (both P<.001). For the Z group, the axial region had the highest volume (19 ±2 mm3), followed by the volumes of the occlusal (15 ±1 mm3) and marginal regions (12 ±1 mm3). The Pearson correlation test determined a moderate positive correlation of the marginal area (r=0.606, P<.001) and of the axial region (r=0.588, P<.001). However, a moderate negative correlation was found between volume and thickness of the occlusal area (r=-0.437, P=.016). CONCLUSIONS: Z showed more volume of cement space, as well as thicker cement space than LD and RN. The µCT analysis is an efficient method of analyzing cement thickness and volume in ceramic crowns at the selected regions of interest. A moderate positive correlation was found between the 2D and 3D analyses for the axial and marginal regions of ceramic crowns.

Comparison of marginal adaptation and internal fit of monolithic lithium disilicate crowns produced by 4 different CAD/CAM systems.

OBJECTIVES: To evaluate the marginal adaptation and internal space of crowns produced by 4 CAD/CAM systems using microcomputed tomography (µCT) and replica technique (RT). MATERIALS AND METHODS: Monolithic lithium disilicate crowns were milled (Ceramill, Cerec, EDG, and Zirkonzahn) (n = 10). The cement film obtained with low viscosity silicone was scanned by the µCT system and captured by a stereomicroscope, according to RT. Two-way ANOVA followed by Tukey's test were used for statistical analysis (α = 0.05). A uniformity index (UI) was idealized to describe the distribution of crowns' internal space and submitted to the Kruskal-Wallis and Tukey's test (α = 0.05). The correlation between µCT and RT was performed by Pearson's Correlation Coeficient (α = 0.05). RESULTS: Marginal adaptation and internal space were statistically significant different between the experimental groups for the µCT and RT (p < 0.05). The medians of the 4 systems tested were within clinically acceptable range and the mean (± SD) highest marginal discrepancy was recorded in the Ceramill group at 133.0 ± 71.5 µm (µCT) and 90.6 ± 38.5 µm (RT). For internal fit, the UI disclosed a better distribution of the internal space for the Zirkonzahn group (p < 0.001). There was a strong correlation between the methods (p = 0.01 and r = 0.69). CLINICAL RELEVANCE: Because of the variability of the CAD/CAM systems available, evaluating their accuracy is of clinical interest. The 4 systems are capable to produce restorations adaptated within clinically appropriate levels. The µCT and RT are efficient adaptation methodologies.

Mechanical Behavior and Fracture Loads of Screw-Retained and Cement-Retained Lithium Disilicate Implant-Supported Crowns.

PURPOSE: To evaluate the fatigue survival, fracture loads and failure modes of monolithic lithium disilicate screw-retained crowns, attached to titanium insert, and cement-retained crowns. MATERIALS AND METHODS: Internal tapered connection implants, embedded in acrylic resin at 30° inclination, were restored with lithium disilicate restorations, simulating a maxillary premolar (n = 20), with different designs: screw-retained titanium base abutment-crowns, and cement-retained crowns. The specimens were submitted to cyclic mechanical loading (1.2 × 106 cycles with a load of 0-250 N at 2 Hz). Surviving specimens were subjected to single load to fracture in a universal testing machine and failure modes were determined with the aid of an optical microscope. Maximum load values were analyzed statistically using the t-test and differences in failure modes were analyzed using the chi-squared test (α = 0.05). RESULTS: All specimens survived the cyclic mechanical loading. Fracture load was significantly higher for screw-retained crowns (821.69 ±196.71 N) than the cement-retained crowns (577.03 ± 137.75 N) (p = 0.005). Ceramic failure was the predominant mode, with no statistical difference between groups. CONCLUSIONS: Screw-retained and cement-retained lithium disilicate crowns survived the cyclic mechanical loading. The use of titanium inserts to support a monolithic restoration enhances the fracture strength of the crown/abutment system.

Analysis of correlation between optical and microtomography measurements of cementation space in CAD-CAM ceramic crowns.

STATEMENT OF PROBLEM: Identical computer-aided design (CAD) parameters may be used to mill a variety of ceramic materials for computer-aided design and computer-aided manufacture (CAD-CAM) crowns. Whether milled crown spacing matches the designed parameters when more than a single evaluation method is applied is unknown. PURPOSE: The purpose of this in vitro study was to correlate the stereomicroscope and the microcomputer tomography (µCT) 2-dimensional analysis of the cementation space with the replica technique in assessing 3 different ceramic materials. MATERIAL AND METHODS: The specimens were milled in lithium disilicate, resin nanoceramic, and zirconia (n=30). The cement space was measured at the marginal, axial, and occlusal regions. One hundred twenty measurements of each material were used to correlate the methodologies. Data were statistically evaluated with 2-way repeated measures ANOVA and the Tukey test (α=.05). The Pearson correlation coefficient was used for each region for both methodologies (µCT and optical microscopy) separately. RESULTS: For the µCT analysis, no differences were observed (P>.05) among the materials, but the axial region showed a positive correlation with the marginal (r=0.957) and occlusal regions (r=0.349); the same was observed between the occlusal and marginal regions (r=0.338). However, for stereomicroscope evaluation, resin nanoceramic and zirconia present similar cementation space (P=960), both being different from lithium disilicate (P<.05). The marginal region presented a positive correlation with axial (r=0.149) and occlusal regions (r=0.344), but the axial region showed negative correlation with the occlusal surface (r=-0.205). CONCLUSIONS: The measurements of the scanned replicas were accurate when thinner sections were under measurement. Although the same space parameters were set in the CAD software program, definitive internal dimensions varied among the milled crowns.

Effects of ZnO/TiO2 nanoparticle and TiO2 nanotube additions to dense polycrystalline hydroxyapatite bioceramic from bovine bones.

OBJECTIVES: A bovine dense hydroxyapatite ceramic (HA) was produced as new biomaterial, however, the production of a material with consistently high flexural strength remains challenging. The objective of this study was to evaluate the effects of ZnO nanoparticles, TiO2 nanoparticles, and TiO2 nanotubes (1%, 2%, and 5% by weight) on the microstructure and flexural strength of a bovine dense hydroxyapatite ceramic (HA). METHODS: Discs (Ø=12.5mm; thickness=1.3mm) were prepared and subjected to X-ray diffraction (XRD), and observation with a field emission scanning electron microscope (FE-SEM), biaxial flexural strength (BFS) testing, and Vickers hardness (VH) testing. The BFS and VH data were subjected to ANOVA and Tukey post-hoc tests (α=0.05) and Weibull analysis. RESULTS: The XRD showed that the addition of nanomaterials caused the formation of a secondary phase when 5% of the ZnO nanoparticles was used, or when all percentages of the TiO2 nanoparticles/nanotubes were used, and the HA crystallographic planes were maintained. Differences were not observed between the higher BFS values obtained with pure HA and those obtained with the 5% addition of TiO2 nanoparticles. However, the results were different compared with the other groups (α=0.05). The results obtained by Weibull analysis revealed that the 1%, 2%, and 5% addition of TiO2 nanotubes, and the 1% and 2% addition of TiO2 nanoparticles decreased the HA characteristic strength (σ0), while the Weibull modulus (m) increased when 5% of TiO2 nanoparticles, 1% and 2% of ZnO nanoparticles, and 2% of TiO2 nanoparticles were added, but with no statistical difference from the pure HA. The 5% addition of ZnO2 nanoparticles decreased the σ0 without changing m. Moreover, the 5% addition of TiO2 nanoparticles resulted in an m closest to that of pure HA. Regarding the VH results, the blend of HA with 1% and 2% addition of TiO2 nanoparticles exhibited the higher values, which were similar between the different addition ratios (p=0.102). Moreover, the addition of 5% TiO2 nanoparticles resulted in higher value compared with pure HA. SIGNIFICANCE: This study demonstrated that the HA blend with 5% of TiO2 nanoparticles has the greatest potential as a bovine HA dense bioceramic reinforcement.

Fatigue survival and damage modes of lithium disilicate and resin nanoceramic crowns.

INTRODUCTION: Polymer-based composite materials have been proposed as an alternative for single unit restorations, due to their resilient and shock absorbing behavior, in contrast to the brittleness of ceramic materials that could result in failure by fracture. OBJECTIVE: To evaluate the fatigue strength and damage modes of monolithic posterior resin nanoceramic and lithium disilicate glass ceramic crowns. METHODOLOGY: Twenty-six resin nanoceramic (RNC) and lithium disilicate glass ceramic (LD) 2 mm monolithic crowns (n=13) were cemented on composite resin replicas of a prepared tooth and subjected to cyclic load with lithium disilicate indenters for 2 million cycles. Specimens and indenters were inspected every 500,000 cycles and suspended when presenting fractures or debonding. Surviving specimens were embedded in epoxy resin, polished and subsurface damage was analyzed. Specimens presenting fractures or severe subsurface damage were considered as failures. Survival data was subjected to Fisher's exact test; damage modes were subjected to Mann-Whitney test (p<0.05). RESULTS: There were no debonding, cohesive or catastrophic failures. Considering subsurface damage, 53.8% of RNC and 46.2% of LD crowns survived the fatigue test, presenting no statistical difference. Chief damage modes were radial cracks for RNC and inner cone cracks for LD, presenting no statistical difference. CONCLUSIONS: The results suggest that if debonding issues can be resolved, resin nanoceramic figures can be an alternative to posterior crowns. Although distinct, damage modes revealed potential to cause bulk fracture in both glass ceramic and resin nanoceramic crowns.

Fatigue survival and damage modes of lithium disilicate and resin nanoceramic crowns

Abstract Polymer-based composite materials have been proposed as an alternative for single unit restorations, due to their resilient and shock absorbing behavior, in contrast to the brittleness of ceramic materials that could result in failure by fracture. Objective: To evaluate the fatigue strength and damage modes of monolithic posterior resin nanoceramic and lithium disilicate glass ceramic crowns. Methodology: Twenty-six resin nanoceramic (RNC) and lithium disilicate glass ceramic (LD) 2 mm monolithic crowns (n=13) were cemented on composite resin replicas of a prepared tooth and subjected to cyclic load with lithium disilicate indenters for 2 million cycles. Specimens and indenters were inspected every 500,000 cycles and suspended when presenting fractures or debonding. Surviving specimens were embedded in epoxy resin, polished and subsurface damage was analyzed. Specimens presenting fractures or severe subsurface damage were considered as failures. Survival data was subjected to Fisher's exact test; damage modes were subjected to Mann-Whitney test (p<0.05). Results: There were no debonding, cohesive or catastrophic failures. Considering subsurface damage, 53.8% of RNC and 46.2% of LD crowns survived the fatigue test, presenting no statistical difference. Chief damage modes were radial cracks for RNC and inner cone cracks for LD, presenting no statistical difference. Conclusions: The results suggest that if debonding issues can be resolved, resin nanoceramic figures can be an alternative to posterior crowns. Although distinct, damage modes revealed potential to cause bulk fracture in both glass ceramic and resin nanoceramic crowns.

Esthetic rehabilitation with zirconia on tooth and morse taper implant: case report / Reabilitação estética em zircônia sobre dente e implante cone morse: caso clínico

Among the ceramic materials used in dentistry, Zirconia presents the ideal opacity for cases where the clinical challenge is to neutralize the difference in the colors of the substrates. The "ceramic steel", so called by some authors, guarantees to Zirconia resistance and hardness similar to a metal, but with aesthetic advantages superior to the metal-ceramic restorations, which can exhibit exposure of the metal band over time. This article describes a complex rehabilitation treatment involving dental elements with different substrates: 11 - vital tooth with large crown damage; 21 ­ endodontically treated tooth and cast metal core; 22 - Morse taper implant. The selection of a completely zirconia-based ceramic system allowed masking the different conditions of substrates, so achieving the esthetic expectations. Moreover, considering the patient's high smile line, excellent gingival esthetics was obtained with an internal connection Morse taper implant associated with an individualized anatomic abutment.

Dentre os materiais cerâmicos utilizados na Odontologia, a Zircônia apresenta a opacidade ideal para os casos em que o desafio clinico é neutralizar a diferença nas cores dos substratos. O "aço cerâmico", assim chamado por alguns autores, garante à Zircônia resistência e dureza semelhantes a um metal, mas com vantagens estéticas superiores às restaurações metalocerâmicas, as quais podem apresentar exposição da cinta metálica ao longo do tempo. Este artigo descreve um tratamento reabilitador complexo, envolvendo elementos dentários com diferentes substratos: 11 - dente vital com ampla destruição coronária; 21 - dente com tratamento endodôntico e núcleo metálico fundido; 22 ­ ausente, reabilitado com implante do tipo cone morse. A seleção do sistema totalmente cerâmico à base de zircônia, permitiu mascarar as diferentes condições dos substratos atingindo as expectativas estéticas. Além disso, diante do sorriso alto gengivoso presente neste caso, a excelência na estética gengival foi obtida utilizando implante com conexão interna do tipo cone morse associado a um pilar anatômico individualizado.

Dimensional changes from the sintering process and fit of Y-TZP copings: Micro-CT analysis.

OBJECTIVE: To evaluate the dimensional changes from the sintering process of Y-TZP and relate them to the fit of zirconia copings. METHODS: The sintering shrinkage rate (SSR) was obtained from the measurement of geometric specimens (4×4×2mm). Thirty-six zirconia copings made using CAD/CAM were equally divided into three groups (n=12): ZMAX - IPS e.max ZirCAD (Ivoclar Vivadent, Liechtenstein); ZYZ - InCeram YZ (Vita Zahnfabrik, Germany); and ZK - Zirklein (Zirklein, Brazil). The copings were scanned in micro-CT before and after sintering so that SSR was obtained. The SSR of geometrical specimens and copings was compared to each other and those the manufacturers reported (ANOVA-2 and Tukey, p≤.05). The copings were settled on an abutment and taken to the micro-CT to evaluate their marginal and internal fit. The data enabled the statistical comparison (ANOVA-2 and Tukey, p≤.05) between groups and measurement sites and between the fit obtained with that stipulated by the CAD/CAM software (80µm) (Dunnett test, p≤.05). RESULTS: All groups showed statistical differences between the SSR the manufacturer reported and those obtained experimentally and between the SSR of the geometric specimens and copings. In general, the SSR of the copings showed no uniformity. There was no statistical difference among the groups for marginal fit, with differences only for internal fit and between the different regions measured. The fit obtained experimentally differed from the internal space determined in the CAD/CAM software. SIGNIFICANCE: The lack of uniformity of sintering shrinkage might lead to a non-uniform internal fit of Y-TZP copings.

Effect of cement space on stress distribution in Y-TZP based crowns.

OBJECTIVE: To evaluate the stress distribution in bi-layered Y-TZP based crowns, according to the occlusal internal spacing between coping and abutment. METHODS: Twelve premolar shaped Y-TZP copings were made by a CAD/CAM system and seated on an abutment to evaluate the internal fit at the occlusal third using micro-CT images. Considering the fitting range obtained experimentally, two 3D finite element models, consisting on bone tissue, a titanium implant, a zirconia abutment, cement layer and a bi-layered Y-TZP ceramic crown were constructed based on the micro-CT images, one corresponding to the thinnest cement space and other representing the specimen with the thickest cement space obtained experimentally. A 250N axial load was applied at the center of the occlusal surface of the crown (≅0,8mm2 area) and the first principal stress distribution was plotted and analyzed. RESULTS: The greatest maximum principal stress occurred within the veneer ceramic right below the site of loading. The thickest cement model showed higher stress concentration at the center of occlusal surface of veneer and the center of occlusal internal surface of coping. SIGNIFICANCE: Knowledge of stress distribution in ceramic crowns with different cement thicknesses will help clinicians to properly adjust crown fit, in seeking to avoid porcelain fractures.

FEA of Peri-Implant Stresses in Fixed Partial Denture Prostheses with Cantilevers.

PURPOSE: To compare stresses in the peri-implant bone produced by fixed partial prostheses with mesial and distal cantilevers, when cemented or screwed onto implants. MATERIALS AND METHODS: The experimental design consisted of four 3D models obtained by volumetric computerized tomography and analyzed using finite element analysis (FEA). Stresses were simulated in two stages. Stage 1 consisted of application of the preload. A 288 N load was applied to pillar screws of the cemented prosthesis, resulting in 389 MPa peak; 257 N was applied to the intermediate screw (multi-unit) resulting in 390 MPa peak; and 111 N was applied to the prosthesis infrastructure screw in the screwed prostheses, resulting in 390 MPa peak. In stage 2, the axial and oblique loads were applied. The axial load consisted of 50 N for molar implants and 30 N for premolar implants. The oblique load (on the buccal slope of the buccal cusp of each crown) consisted of 30 N for premolar implants and 50 N for molar implants, with a buccolingual vector at a 45° angle with the occlusal plane. The response variables were the axial and oblique stresses on the peri-implant bone, according to the following groups: group 1-models of fixed partial prostheses cemented onto implants with mesial or distal cantilevers; group 2-models of fixed partial denture screwed onto implants with mesial or distal cantilevers. Data were recorded, evaluated, and compared. RESULTS: Oblique loads produced higher peak values than axial loads, and were located at the bone crest of the implant closest to the cantilever, regardless of the prosthesis type. In the cemented prosthesis models, oblique loads produced the highest peaks in the primary implant region when compared with the screwed prosthesis models. CONCLUSION: The screwed fixed prostheses caused less stress on peri-implant bone regardless of whether the cantilever was located mesially or distally.

Effect of cantilever length and alloy framework on the stress distribution in peri-implant area of cantilevered implant-supported fixed partial dentures.

Because many mechanical variables are present in the oral cavity, the proper load transfer between the prosthesis and the bone is important for treatment planning and for the longevity of the implant-supported fixed partial denture. Objectives To verify the stress generated on the peri-implant area of cantilevered implant-supported fixed partial dentures and the potential effects of such variable. Material and Methods A U-shaped polyurethane model simulating the mandibular bone containing two implants (Ø 3.75 mm) was used. Six groups were formed according to the alloy's framework (CoCr or PdAg) and the point of load application (5 mm, 10 mm and 15 mm of cantilever arm). A 300 N load was applied in pre-determined reference points. The tension generated on the mesial, lingual, distal and buccal sides of the peri-implant regions was assessed using strain gauges. Results Two-way ANOVA and Tukey statistical tests were applied showing significant differences (p<0.05) between the groups. Pearson correlation test (p<0.05) was applied showing positive correlations between the increase of the cantilever arm and the deformation of the peri-implant area. Conclusions This report demonstrated the CoCr alloy shows larger compression values compared to the PdAg alloy for the same distances of cantilever. The point of load application influences the deformation on the peri-implant area, increasing in accordance with the increase of the lever arm.

Effect of cantilever length and alloy framework on the stress distribution in peri-implant area of cantilevered implant-supported fixed partial dentures

ABSTRACT Because many mechanical variables are present in the oral cavity, the proper load transfer between the prosthesis and the bone is important for treatment planning and for the longevity of the implant-supported fixed partial denture. Objectives To verify the stress generated on the peri-implant area of cantilevered implant-supported fixed partial dentures and the potential effects of such variable. Material and Methods A U-shaped polyurethane model simulating the mandibular bone containing two implants (Ø 3.75 mm) was used. Six groups were formed according to the alloy’s framework (CoCr or PdAg) and the point of load application (5 mm, 10 mm and 15 mm of cantilever arm). A 300 N load was applied in pre-determined reference points. The tension generated on the mesial, lingual, distal and buccal sides of the peri-implant regions was assessed using strain gauges. Results Two-way ANOVA and Tukey statistical tests were applied showing significant differences (p<0.05) between the groups. Pearson correlation test (p<0.05) was applied showing positive correlations between the increase of the cantilever arm and the deformation of the peri-implant area. Conclusions This report demonstrated the CoCr alloy shows larger compression values compared to the PdAg alloy for the same distances of cantilever. The point of load application influences the deformation on the peri-implant area, increasing in accordance with the increase of the lever arm.

Fractographic principles applied to Y-TZP mechanical behavior analysis.

The purpose of this study was to evaluate the use of fractography principles to determine the fracture toughness of Y-TZP dental ceramic in which KIc was measured fractographically using controlled-flaw beam bending techniques and to correlate the flaw distribution with the mechanical properties. The Y-TZP blocks studied were: Zirconia Zirklein (ZZ); Zirconcad (ZCA); IPS e.max ZirCad (ZMAX); and In Ceram YZ (ZYZ). Samples were prepared (16mm×4mm×2mm) according to ISO 6872 specifications and subjected to three-point bending at a crosshead speed of 0.5mm/min. Weibull probability curves (95% confidence bounds) were calculated and a contour plot with the Weibull modulus (m) versus characteristic strength (σ0) was used to examine the differences among groups. The fractured surface of each specimen was inspected in a scanning electron microscope (SEM) for qualitative and quantitative fractographic analysis. The critical defect size (c) and fracture toughness (KIc) were estimated. The fractured surfaces of the samples from all groups showed similar fractographic characteristics, except ZCA showed pores and defects. Fracture toughness and the flexural strength values were not different among the groups except for ZCA. The characteristic strength (p<0.05) of ZZ (η=920.4) was higher than the ZCA (η=651.1) and similar to the ZMAX (η=983.6) and ZYZ (η=1054.8). By means of quantitative and qualitative fractographic analysis, this study showed fracture toughness and strength that could be correlated to the observable microstructural features of the evaluated zirconia polycrystalline ceramics.

An Indirect Method to Measure Abutment Screw Preload: A Pilot Study Based on Micro-CT Scanning

This study aimed to measure the preload in different implant platform geometries based on micro-CT images. External hexagon (EH) implants and Morse Tapered (MT) implants (n=5) were used for the preload measurement. The abutment screws were scanned in micro-CT to obtain their virtual models, which were used to record their initial length. The abutments were screwed on the implant with a 20 Ncm torque and the set composed by implant, abutment screw and abutment were taken to the micro-CT scanner to obtain virtual slices of the specimens. These slices allowed the measurement of screw lengths after torque application and based on the screw elongation. Preload values were calculated using the Hooke's Law. The preloads of both groups were compared by independent t-test. Removal torque of each specimen was recorded. To evaluate the accuracy of the micro-CT technique, three rods with known lengths were scanned and the length of their virtual model was measured and compared with the original length. One rod was scanned four times to evaluate the measuring method variation. There was no difference between groups for preload (EH = 461.6 N and MT = 477.4 N), but the EH group showed higher removal torque values (13.8±4.7 against 8.2±3.6 Ncm for MT group). The micro-CT technique showed a variability of 0.053% and repeatability showed an error of 0.23 to 0.28%. Within the limitations of this study, there was no difference between external hexagon and Morse taper for preload. The method using micro-CT may be considered for preload calculation.

Resumo Este estudo teve como objetivo medir a pré-carga em diferentes conexões implante/pilar baseado em imagens de micro-CT. Implantes de hexágono externo (EH) e Cone Morse (MT) (n = 5) foram utilizados para a medição de pré-carga. Os parafusos de pilares foram digitalizados em um micro-CT de alta resolução para obter seus modelos virtuais, que foram utilizados para registrar o comprimento inicial. Os pilares foram parafusados sobre o implante com um torque de 20 Ncm e, o conjunto composto por implante, parafuso do pilar e pilar foi levado para o micro-CT para obter cortes virtuais dos espécimes. Esses cortes permitiram a medida do comprimento dos parafusos após a aplicação do torque. Assim, com base no alongamento dos parafusos, os valores de pré-carga foram calculados usando a Lei de Hooke. A pré-carga de ambos os grupos foram comparados pelo Test-t independente. O torque de remoção de cada espécime foi registrado. Para avaliar a precisão da técnica de micro-CT, três bastões foram escaneados em micro-CT e o comprimento do seu modelo virtual foi comparado com o comprimento original dos bastões. Um bastão foi digitalizado e mensurado quatro vezes para avaliar a variação do método de medição e a sua repetitividade. Não houve diferença entre os grupos para a pré-carga (EH = 461,6 N e MT = 477,4 N), no entanto o grupo EH apresentou maiores valores de torque de afrouxamento do parafuso (13,8 ± 4,7 contra 8,2 ± 3,6 Ncm para o grupo MT). A técnica de micro-CT mostrou uma variabilidade de 0,053% e a repetitividade apresentou um erro de 0,23 a 0,28%. Dentro das limitações deste estudo, não houve diferença entre Hexágono Externo e Cone Morse para pré-carga. O método baseado em imagens de micro-CT pode ser considerado para mensuração da pré-carga.

Stress Distribution in Single Dental Implant System: Three-Dimensional Finite Element Analysis Based on an In Vitro Experimental Model.

This study aimed to analyze the stress distribution in single implant system and to evaluate the compatibility of an in vitro model with finite element (FE) model. The in vitro model consisted of Brånemark implant; multiunit set abutment of 5 mm height; metal-ceramic screw-retained crown, and polyurethane simulating the bone. Deformations were recorded in the peri-implant region in the mesial and distal aspects, after an axial 300 N load application at the center of the occlusal aspect of the crown, using strain gauges. This in vitro model was scanned with micro CT to design a three-dimensional FE model and the strains in the peri-implant bone region were registered to check the compatibility between both models. The FE model was used to evaluate stress distribution in different parts of the system. The values obtained from the in vitro model (20-587 µÎµ) and the finite element analysis (81-588 µÎµ) showed agreement among them. The highest stresses because of axial and oblique load, respectively were 5.83 and 40 MPa for the cortical bone, 55 and 1200 MPa for the implant, and 80 and 470 MPa for the abutment screw. The FE method proved to be effective for evaluating the deformation around single implant. Oblique loads lead to higher stress concentrations.

Application of Micro-Raman Spectroscopy to the Study of Yttria-Stabilized Tetragonal Zirconia Polycrystal (Y-TZP) Phase Transformation.

The aim of this study was to perform micro-Raman spectroscopy as an alternative and nondestructive method to identify the phase transformation of zirconia after mechanical stress. The groups evaluated were experimental zirconia, zirconcad, IPS e.max ZirCad, and In Ceram YZ. Ten specimens were constructed for each group (n = 30) and subjected to a three-point bending test with a crosshead speed of 0.5 mm/min. The fractured surfaces were analyzed by micro-Raman spectroscopy. The laser power was kept at 10 mW, and scanning was performed in three regions of the fractured surface: (i) near the source of the failure (region of tensile stress), (ii) central to the fractured surface, and (iii) far from the source of failure. All materials showed the characteristic bands of tetragonal and monoclinic phases of zirconia. All zirconia studied showed a monoclinic phase in the tensile stress region. Micro-Raman spectroscopy was effective in detecting the presence of crystalline phases in polycrystals ceramics.

An Indirect Method to Measure Abutment Screw Preload: A Pilot Study Based on Micro-CT Scanning.

This study aimed to measure the preload in different implant platform geometries based on micro-CT images. External hexagon (EH) implants and Morse Tapered (MT) implants (n=5) were used for the preload measurement. The abutment screws were scanned in micro-CT to obtain their virtual models, which were used to record their initial length. The abutments were screwed on the implant with a 20 Ncm torque and the set composed by implant, abutment screw and abutment were taken to the micro-CT scanner to obtain virtual slices of the specimens. These slices allowed the measurement of screw lengths after torque application and based on the screw elongation. Preload values were calculated using the Hooke's Law. The preloads of both groups were compared by independent t-test. Removal torque of each specimen was recorded. To evaluate the accuracy of the micro-CT technique, three rods with known lengths were scanned and the length of their virtual model was measured and compared with the original length. One rod was scanned four times to evaluate the measuring method variation. There was no difference between groups for preload (EH = 461.6 N and MT = 477.4 N), but the EH group showed higher removal torque values (13.8 ± 4.7 against 8.2 ± 3.6 N cm for MT group). The micro-CT technique showed a variability of 0.053% and repeatability showed an error of 0.23 to 0.28%. Within the limitations of this study, there was no difference between external hexagon and Morse taper for preload. The method using micro-CT may be considered for preload calculation.

Effect of veneering material on the deformation suffered by implant-supported fixed prosthesis framework.

UNLABELLED: Knowing how stresses are dissipated on the fixed implant-supported complex allows adequate treatment planning and better choice of the materials used for prosthesis fabrication. OBJECTIVES: The aim of this study was to evaluate the deformation suffered by cantilevered implant-supported fixed prostheses frameworks cast in silver-palladium alloy and coated with two occlusal veneering materials: acrylic resin or porcelain. MATERIAL AND METHODS: Two strain gauges were bonded to the inferior surface of the silver-palladium framework and two other were bonded to the occlusal surface of the prosthesis framework covered with ceramic and acrylic resin on each of its two halves. The framework was fixed to a metallic master model and a 35.2 N compression force was applied to the cantilever at 10, 15 and 20 mm from the most distal implant. The measurements of deformation by compression and tension were obtained. The statistical 2-way ANOVA test was used for individual analysis of the experiment variables and the Tukey test was used for the interrelation between all the variables (material and distance of force application). RESULTS: The results showed that both variables had influence on the studied factors (deformation by compression and tension). CONCLUSION: The ceramic coating provided greater rigidity to the assembly and therefore less distortion compared with the uncoated framework and with the resin-coated framework. The cantilever arm length also influenced the prosthesis rigidity, causing higher deformation the farther the load was applied from the last implant.