ABSTRACT
Fouling is a major obstacle in the introduction of membrane processes in new applications in the pulping industry. Due to the complex nature of the feed solutions, complementary analysis methods are usually needed to identify the substances involved. Four different methods were used for the comprehensive analysis of a membrane removed from an ultrafiltration plant treating alkaline bleach plant effluent in a sulfite pulp mill to identify the substances causing fouling. Magnesium was detected both on the membrane surface and in the nonwoven membrane backing and a small amount of polysaccharides was detected after acid hydrolysis of the fouled membrane. This study provides information on foulants, which can be used to improve processing conditions and cleaning protocols and thus the membrane performance in pulp mill separation processes. It also provides an overview of the usefulness of various analytical methods.
ABSTRACT
The colloidal stability of lipid based cubosomes, aqueous dispersion of inverse bicontinuous cubic phase, can be significantly increased by a stabilizer. The most commonly used stabilizers are non-ionic tri-block copolymers, poloxamers, which adsorb at the lipid-water interface and hence sterically stabilize the dispersion. One of the challenges with these synthetic polymers is the effect on the internal structure of the cubosomes and the potential toxicity when these nanoparticles are applied as nanomedicine platforms. The natural polysaccharide, softwood hemicellulose, has been proved to be an excellent stabilizer for oil-in-water emulsions, partially due to the presence of hydrophobic lignin in the extract which to some extent is associated to hemicellulose. Herein, we reported for the first time cubosomes stabilized by two types of softwood hemicelluloses, where one is extracted through thermomechanical pulping (TMP, low lignin content) and the other obtained from sodium-based sulfite liquor (SSL, high lignin content). The effect of the two hemicellulose samples on the colloidal stability and structure of monoolein-based cubosomes have been investigated via DLS, SAXS, AFM and cryo-TEM. The data obtained suggest that both types of the hemicelluloses stabilize monoolein (GMO) based cubosomes in water without significantly affecting their size, morphology and inner structure. SSL-extracted hemicellulose yields the most stable cubosomes, likely due to the higher content of lignin in comparison to TMP-stabilized ones. In addition, the stability of these particles was tested under physiological conditions relevant to possible application as drug carriers.
Subject(s)
Liquid Crystals , Nanoparticles , Particle Size , Polysaccharides , Scattering, Small Angle , X-Ray DiffractionABSTRACT
Membrane fouling is the major factor limiting the wider applicability of the membrane-based technologies in water treatment and in separation and purification processes of biorefineries, pulp and paper industry, food industry and other sectors. Endeavors to prevent and minimize fouling requires a deep understanding on the fouling mechanisms and their relative effects. In this study, Brunauer-Emmett-Teller (BET) nitrogen adsorption/desorption technique was applied to get an insight into pore-level membrane fouling phenomena occurring in ultrafiltration of wood-based streams. The fouling of commercial polysulfone and polyethersulfone membranes by black liquor, thermomechanical pulping process water and pressurized hot-water extract was investigated with BET analysis, infrared spectroscopy, contact angle analysis and pure water permeability measurements. Particular emphasis was paid to the applicability of BET for membrane fouling characterization. The formation of a fouling layer was detected as an increase in cumulative pore volumes and pore areas in the meso-pores region. Pore blocking was seen as disappearance of meso-pores and micro-pores. The results indicate that the presented approach of using BET analysis combined with IR spectroscopy can provide complementary information revealing both the structure of fouling layer and the chemical nature of foulants.
ABSTRACT
The pulp and paper industry is one of the most important industrial sectors worldwide, and has considerable potential for the sustainable fractionation of lignocellulosic biomass to provide valuable compounds. Ultrafiltration (UF) is a suitable separation technique for the profitable production of hemicelluloses from process water from thermomechanical pulping (ThMP), but is limited by membrane fouling. Improvements in cleaning protocols and new alternative cleaning agents are required to ensure a long membrane lifetime, and thus a sustainable process. This study, therefore, focuses on the cleaning of polymeric UF membranes after the filtration of ThMP process water, comparing alkaline with enzymatic cleaning agents. The aim was to develop a cleaning procedure that is efficient under mild conditions, resulting in a lower environmental impact. It was not possible to restore the initial permeability of the membrane when cleaning the membrane with enzymes alone, but the permeability was restored when using a two-step cleaning process with enzymes in the first step and an alkaline cleaning agent in the second step. Scanning electron microscopy gave a deeper inside into the cleaning efficiency. Attenuated total reflectance Fourier-transform infrared spectroscopy analysis confirmed that not only polysaccharides, but also extractives are adsorbed onto the membrane surface.
