In situ monitoring of laser-induced periodic surface structures formation on polymer films by grazing incidence small-angle X-ray scattering.

The formation of laser-induced periodic surface structures (LIPSS) on model spin-coated polymer films has been followed in situ by grazing incidence small-angle X-ray scattering (GISAXS) using synchrotron radiation. The samples were irradiated at different repetition rates ranging from 1 up to 10 Hz by using the fourth harmonic of a Nd:YAG laser (266 nm) with pulses of 8 ns. Simultaneously, GISAXS patterns were acquired during laser irradiation. The variation of both the GISAXS signal with the number of pulses and the LIPSS period with laser irradiation time is revealing key kinetic aspects of the nanostructure formation process. By considering LIPSS as one-dimensional paracrystalline lattice and using a correlation found between the paracrystalline disorder parameter, g, and the number of reflections observed in the GISAXS patterns, the variation of the structural order of LIPSS can be assessed. The role of the laser repetition rate in the nanostructure formation has been clarified. For high pulse repetition rates (i.e., 10 Hz), LIPSS evolve in time to reach the expected period matching the wavelength of the irradiating laser. For lower pulse repetition rates LIPSS formation is less effective, and the period of the ripples never reaches the wavelength value. Results support and provide information on the existence of a feedback mechanism for LIPSS formation in polymer films.

Mapping the structural order of laser-induced periodic surface structures in thin polymer films by microfocus beam grazing incidence small-angle X-ray scattering.

In this work we present an accurate mapping of the structural order of laser-induced periodic surface structures (LIPSS) in spin-coated thin polymer films, via a microfocus beam grazing incidence small-angle X-ray scattering (µGISAXS) scan, GISAXS modeling, and atomic force microscopy imaging all along the scanned area. This combined study has allowed the evaluation of the effects on LIPSS formation due to nonhomogeneous spatial distribution of the laser pulse energy, mapping with micrometric resolution the evolution of the period and degree of structural order of LIPSS across the laser beam diameter in a direction perpendicular to the polarization vector. The experiments presented go one step further toward controlling nanostructure formation in LIPSS through a deep understanding of the parameters that influence this process.

Micro- and submicrostructuring thin polymer films with two and three-beam single pulse laser interference lithography.

In this work we report the application of two and three-beam single pulse laser interference lithography to thin polymer films of poly(trimethylene terephthalate) (PTT). By irradiating the sample surface with temporary and spatially overlapped single pulses from two or three coherent beams and changing the angles of incidence, we have accomplished the fabrication of large-area polymer micro and submicrogratings as well as submicrometric cavities arranged in a hexagonal lattice. The characterization of the structures in real space by atomic force microscopy (AFM) and scanning electron microscopy (SEM) has allowed us to determine the formation mechanism of the microgratings to be based on different ablation regimes depending on the local fluence. Moreover, complementary characterization of the submicrometric cavities in reciprocal space by grazing incidence small-angle X-ray scattering (GISAXS) confirms the existence of large areas where two-dimensional order is present. The experiments presented in this work demonstrate the suitability of single pulse laser interference lithography for micro and submicrostructuring polymer films, opening up new possibilities for patterning and paving the way for potential applications where polymer structures are involved.

Assessment of femtosecond laser induced periodic surface structures on polymer films.

In this work we present the formation of laser induced periodic surface structures (LIPSS) on spin-coated thin films of several model aromatic polymers including poly(ethylene terephthalate), poly(trimethylene terephthalate) and poly carbonate bis-phenol A upon irradiation with femtosecond pulses of 795 and 265 nm at fluences well below the ablation threshold. LIPSS are formed with period lengths similar to the laser wavelength and parallel to the direction of the laser polarization vector. Formation of LIPSS upon IR irradiation at 795 nm, a wavelength at which the polymers absorb weakly, contrasts with the absence of LIPSS in this spectral range upon irradiation with nanosecond pulses. Real and reciprocal space characterization of LIPSS obtained by Atomic Force Microscopy (AFM) and Grazing Incidence Small Angle X-ray Scattering (GISAXS), respectively, yields well correlated morphological information. Comparison of experimental and simulated GISAXS patterns suggests that LIPSS can be suitably described considering a quasi-one-dimensional paracrystalline lattice and that irradiation parameters have an influence on the order of such a lattice. Fluorescence measurements, after laser irradiation, provide indirect information about dynamics and structure of the polymer at the molecular level. Our results indicate that the LIPSS are formed by interference of the incident and surface scattered waves. As a result of this process, heating of the polymer surface above its glass transition temperature takes place enabling LIPSS formation.

Understanding crystallization features of P(VDF-TrFE) copolymers under confinement to optimize ferroelectricity in nanostructures.

The successful development of ferroelectric polymer devices depends on the effective fabrication of polar ferroelectric crystalline nanostructures. We demonstrate, by scanning X-ray microdiffraction using synchrotron light, the heterogeneous character of high aspect ratio one-dimensional nanoarrays of poly(vinylidene fluoride-co-trifluoroethylene) copolymers supported by a residual polymer film. They were prepared by melt and solution template wetting, using porous anodic aluminum oxide as a template. The spatial evolution of different polymorphs from the mixture of paraelectric and ferroelectric crystal forms (residual film) to the pure ferroelectric form (nanoarray) is evidenced for the samples prepared by solution wetting. However, for samples prepared by melt wetting the ferroelectric phase is exclusively obtained in both the residual film and nanoarray. The crystal nuclei formed in the polymer film connected to the nanoarray play a key role in determining the formation of a crystallinity distribution gradient, where the crystallinity decreases along the first 5-10 microns in the nanorods reaching a steady value afterwards. The minimum decrease in crystallinity is revealed for samples prepared by melt wetting. The results reported in this work endeavour to enhance the understanding of crystallization under confinement for ferroelectric copolymers and reveal the parameters for improving the ferroelectric character of polymer nanostructures.

Crystallization under one-dimensional confinement in alumina nanopores of poly(trimethylene terephthalate) and its composites with single wall carbon nanotubes.

We report the preparation of semicrystalline polymer nanorods of PTT and of its nanocomposites with SWCNTs by infiltration of the molten polymer into disordered anodic alumina membranes. An accurate study of the crystalline orientation of these systems has been accomplished by means of X-ray microdiffraction. While polymer residual film exhibits isotropic character, edge-on lamellae are formed upon approaching the polymer/membrane interface. This effect might be due to the elongational flow that takes place in the molten state as polymer chains infiltrate the AAO membrane. At the interface, edge-on and flat-on crystalline lamellae coexist as a consequence of the strong interaction between the polymer and the AAO surface. Inside the nanopores, the confined environment induces a kinetic selection of polymer crystals which only allows the growth of crystalline lamellae with its a-axis parallel to that of the pore. In the case of PTT/SWCNT nanocomposites, this effect, in conjunction with the strong interaction between polymer and AAO surface, seems to prevail over the templating effect of the carbon nanotubes and a similar orientation to that of the neat PTT case is observed.

Gold coatings on polymer laser induced periodic surface structures: assessment as substrates for surface-enhanced Raman scattering.

We report on the fabrication of gold coated nanostructured polymer thin films and on their characterization as substrates for surface enhanced Raman spectroscopy (SERS). Laser induced periodic surface structures (LIPSS) were obtained on thin polymer films of poly(trimethylene terephthalate) (PTT) upon laser irradiation with the fourth harmonic of a Nd:YAG laser (266 nm, pulse duration 6 ns) resulting in a period close to the incident wavelength. The nanostructured polymer substrates were coated with a nanoparticle assembled gold layer by pulsed laser deposition using the fifth harmonic of a Nd:YAG laser (213 nm, pulse duration 15 ns). Different deposition times resulted in thicknesses from a few nanometres up to several tens of nanometres. Analysis by atomic force microscopy and grazing incident small angle X-ray scattering showed that gold coating preserved the LIPSS relief. The capabilities of the produced nanostructures as substrates for SERS have been investigated using benzenethiol as a test molecule. The SERS signal is substantially larger than that observed for a gold-coated flat substrate. Advantages of this new type of SERS substrates are discussed.

Correlation lengths, porosity and water adsorption in TiO2 thin films prepared by glancing angle deposition.

This paper reports a thorough microstructural characterization of glancing angle deposited (GLAD) TiO(2) thin films. Atomic force microscopy (afm), grazing-incidence small-angle x-ray scattering (GISAXS) and water adsorption isotherms have been used to determine the evolution of porosity and the existence of some correlation distances between the nanocolumns constituting the basic elements of the film's nanostructure. It is found that the deposition angle and, to a lesser extent, the film thickness are the most important parameters controlling properties of the thin film. The importance of porosity and some critical dimensions encountered in the investigated GLAD thin films is highlighted in relation to the analysis of their optical properties when utilized as antireflective coatings or as hosts and templates for the development of new composite materials.

Assessment and formation mechanism of laser-induced periodic surface structures on polymer spin-coated films in real and reciprocal space.

In this work we evaluate the potential of grazing incidence X-ray scattering techniques in the investigation of laser-induced periodic surface structures (LIPSSs) in a series of strongly absorbing model spin-coated polymer films which are amorphous, such as poly(ethylene terephthalate), poly(trimethylene terephthalate), and poly(carbonate bisphenol A), and in a weaker absorbing polymer, such as semicrystalline poly(vinylidene fluoride), over a narrow range of fluences. Irradiation was performed with pulses of 6 ns at 266 nm, and LIPSSs with period lengths similar to the laser wavelength and parallel to the laser polarization direction are formed by devitrification of the film surface at temperatures above the characteristic glass transition temperature of the polymers. No crystallization of the surface is induced by laser irradiation, and crystallinity of the material prevents LIPSS formation. The structural information obtained by both atomic force microscopy and grazing incidence small-angle X-ray scattering (GISAXS) correlates satisfactorily. Comparison of experimental and simulated GISAXS patterns suggests that LIPSSs can be well described considering a quasi-one-dimensional paracrystalline lattice and that irradiation parameters have an influence on the order of such a lattice.

Structure of glancing incidence deposited TiO(2) thin films as revealed by grazing incidence small-angle X-ray scattering.

For the first time, grazing incidence small-angle X-ray scattering (GISAXS) analysis is used to characterize the morphology of TiO(2) thin films grown by glancing angle physical vapor deposition (GLAD). According to cross-section scanning electron microscopy (SEM) images, the films consist of near isotilted TiO(2) columns of different length and width depending on film thickness. The obtained GISAXS patterns show a characteristic asymmetry with respect to the incidence plane, which is associated with the tilted geometry of the TiO(2) columns. The patterns also show the existence of two populations of columns in these GLAD-TiO(2) films. The population of the thinnest columns appears related to the first grown layer and is common for all the films investigated, while the second population of columns grows with the thickness of the films and has been related to wider columns formed by shadowing at the expense of the initially formed columns.

Confinement-induced one-dimensional ferroelectric polymer arrays.

This work demonstrates the use of wetting nanoporous alumina template with polymer solution to produce arrays of isolated poly(vinylidene fluoride) (PVDF) ferroelectric gamma-type nanorods supported within a nonpolar alpha-structure film. The method is based upon a crystal phase transition which occurs due to PVDF confinement within alumina nanoporous. The system was studied using scanning X-ray microdiffraction (micro-XRD) that allows the solid-solid phase transition from the alpha-nonpolar crystal form (bulk) to the gamma polar ferroelectric form (nanorod array) to be spatially resolved, as well as providing crystallinity and orientation information. The results reveal that the interaction between polymer chains and the porous membrane's walls imposes a flat-on lamella growth along the nanorrods long axis, while improving crystal orientation.

Stacking of main chain-crown ether polymers in thin films.

Thin films (9-70 nm) of a series of polymers containing in the main chain dibenzo-18-crown-6 ether unit (DB18C6) linked to an aliphatic spacer of different length (10C and 14C) and nature have been prepared, from chloroform solutions, by spin coating on a silicon substrate. The quality and homogeneity of the polymer coatings was revealed by their reflectivity spectra and atomic force microscopy (AFM). The grazing incidence small-angle X-ray scattering (GISAXS) patterns show an out-of-plane structure correlation (interference maximum near the horizon) of scale size related to the polymer repeating unit length. Above this Bragg reflection, the shape of the scattering observed, in the GISAXS pattern, reveals an orientation of the stacked molecular columns in the coated polymer. A thermal treatment of the samples improves the nanostructure by increasing the lamellar coherence size (in y-direction) as well as the vertical orientation of the molecular columns.