ABSTRACT
OBJECTIVES: This study evaluated surface roughness, biaxial flexural strength, and phase transformation of 5Y-PSZ after grinding and polishing with different protocols. MATERIAL AND METHODS: Two commercial 5Y-PSZ, Lava Esthetic (L) and Cercon xt (C), were used and divided into 3 groups: LC and CC represented unpolished control groups; LE and CE were polished with protocol I (EVE DIASYNT® PLUS HP following with EVE DIACERA RA); and LJ and CJ were polished with protocol II (Superfine diamond bur following with Jota ZIR Gloss polishing kit). Surface roughness was evaluated after polishing step-by-step with a contact-type profilometer. After high-gross polishing, the specimens were subjected to biaxial flexural strength test, crystallographic microstructure analysis using an X-ray diffractometer (XRD), and surface micro-topography using scanning electron microscopy (SEM). STATISTICAL ANALYSIS: Surface roughness differences after each step and biaxial flexural strength between groups were evaluated with one-way ANOVA, followed by Bonferroni post-hoc analysis. Changes in surface roughness across four different time points within groups were assessed using one-way repeated measures ANOVA, followed by Bonferroni post-hoc analysis. RESULTS: After high-gross polishing, both polishing protocols showed significantly lower surface roughness than the grinding group (p < 0.05). The LE and CE groups exhibited the highest surface roughness values, which were significant differences from the LJ and CJ groups (p < 0.05). The LE group showed significantly lower biaxial flexural strength compared to the LC group (p < 0.05). However, there was no statistically significant difference in the CE and CJ groups compared to the control group (p > 0.05). Furthermore, all polishing protocols did not change the phase transformation of zirconia. CONCLUSION: Polishing protocol II provided a smoother surface than the protocol I after high-gross polishing, while the biaxial flexural strength of materials remained unaffected.
ABSTRACT
OBJECTIVE: This study aimed to develop enamel substitute material using a mechanochemical technique. MATERIALS AND METHODS: Hydroxyapatite was synthesized with and without tricalcium phosphate under uniaxial pressing of 10 and 17 MPa (HA10, HA17, BCP10, and BCP17), followed by sintering at 1250 °C for 2 h. Human enamel and dentin blocks were used as control groups. The mechanical properties were determined by compressive strength test and Vickers microhardness. The data were analyzed with one-way ANOVA and LSD post-hoc test (α = 0.05). The phase formation and morphology of the specimens were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). RESULTS: HA17 and HA10 had compressive strength values comparable to enamel and dentin, respectively (p > 0.05). The microhardness of all synthesized groups was significantly higher than that of tooth structures (p < 0.05). From the XRD graphs, only the hydroxyapatite peak was observed in the control and HA groups. SEM images showed homogeneous hydroxyapatite grains in all groups, while the BCP groups contained higher porosities. CONCLUSIONS: Both HA10 and HA17 are suitable for use as the inorganic part of dentin and enamel substitutes.
ABSTRACT
OBJECTIVES: Virgin coconut oil (VCO) pulling has antimicrobial activity and has been promoted as beneficial to oral health; however, limited information exists on its clinical effectiveness. This study aimed to compare the microbiological effects of VCO with palm oil (PO) pulling when used as an adjunctive oral hygiene care. MATERIALS AND METHODS: Thirty-six volunteers with gingival inflammation were randomly assigned to start with (1) VCO (test) and (2) PO (control) interventions in a crossover design. Oil pulling was performed for 28 days adjunctively to oral hygiene routine. After a 21-day wash-out period, the participants switched the oil type and restarted the protocol. Plaque samples were collected for microbial culture at baseline, after the first oil pulling period, after washout, and after the second oil pulling period. The total, aerobic, and anaerobic bacteria and Mutans streptococci (MS) counts were recorded. The mean differences between VCO and PO were compared by paired t-test. RESULTS: The number of total, aerobic, or anaerobic bacteria after 28 days of oil pulling was not significantly different from baseline in both PO and VCO groups. However, PO pulling demonstrated a significant reduction from baseline of MS count (P = 0.010), while VCO pulling showed no significant reduction. There was no statistically significant difference in the mean changes of any microbiological parameters between the two treatments. CONCLUSIONS: VCO pulling did not show statistically significant superior benefit against plaque bacteria over PO pulling. Using PO pulling as an adjunctive oral hygiene care may reduce the number of MS, but this requires further investigations.
