Customizing the hydrolytic degradation rate of stereocomplex PLA through different PDLA architectures.

Stereocomplexation of poly(L-lactide) (PLLA) with star shaped D-lactic acid (D-LA) oligomers with different architectures and end-groups clearly altered the degradation rate and affected the degradation product patterns. Altogether, nine materials were studied: standard PLLA and eight blends of PLLA with either 30 or 50 wt % of four different D-LA oligomers. The influence of several factors, including temperature, degradation time, and amount and type of D-LA oligomer, on the hydrolytic degradation process was investigated using a fractional factorial experimental design. Stereocomplexes containing star shaped D-LA oligomers with four alcoholic end-groups underwent a rather slow hydrolytic degradation with low release of degradation products. Materials with linear D-LA oligomers exhibited similar mass loss but released higher concentrations of shorter acidic degradation products. Increasing the fraction of D-LA oligomers with a linear structure or with four alcoholic end-groups resulted in slower mass loss due to higher degree of stereocomplexation. The opposite results were obtained after addition of D-LA oligomers with carboxylic chain-ends. These materials demonstrated lower degree of stereocomplexation and larger mass and molar mass loss, and also the release of degradation products increased. Increasing the number of alcoholic chain-ends from four to six decreased the degree of stereocomplexation, leading to faster mass loss. The degree of stereocomplexation and degradation rate were customized by changing the architecture and end-groups of the D-LA oligomers.

From lactic acid to poly(lactic acid) (PLA): characterization and analysis of PLA and its precursors.

The quality of the monomers lactic acid and lactide as well as the chemical changes induced during polymerization and processing are crucial parameters for controlling the properties of the resulting poly(lactic acid) (PLA) products. This review presents the most important analysis and characterization methods for quality assessment of PLA and its precursors. The impurities typically present in lactic acid or lactide monomers and their possible origins and effects on resulting PLA products are discussed. The significance of the analyses for the different polymer production stages is considered, and special applications of the methods for studying features specific for PLA-based materials are highlighted.

Polylactide stereocomplexation leads to higher hydrolytic stability but more acidic hydrolysis product pattern.

Poly-l-lactide/poly-d-lactide (PLLA/PDLA) stereocomplex had much higher hydrolytic stability compared to plain PLLA, but at the same time shorter and more acidic degradation products were formed. Both materials were subjected to hydrolytic degradation in water and in phosphate buffer at 37 and 60 degrees C, and the degradation processes were monitored by following mass loss, water uptake, thermal properties, surface changes, and pH of the aging medium. The degradation product patterns were determined by electrospray ionization-mass spectrometry (ESI-MS). The high crystallinity and strong secondary interactions in the stereocomplex prevented water uptake and resulted in lower mass loss and degradation rate. However, somewhat surprisingly, the pH of the aging medium decreased much faster in the case of PLLA/PDLA stereocomplex. In accordance, the ESI-MS results showed that hydrolysis of PLLA/PDLA resulted in shorter and more acidic degradation products. This could be explained by the increased intermolecular crystallization due to stereocomplexation, which results in an increased number of tie chains. Because mainly these short tie chains are susceptible to hydrolysis this leads to formation of shorter oligomers compared to hydrolysis of regular PLLA.

Readily controllable step-growth polymerization method for poly(lactic acid) copolymers having a high glass transition temperature.

Poly(lactic acid) (PLA) copolymers having a significantly higher glass transition temperature (T(g)) than that of high molar mass PLA homopolymers (typically 60 +/- 5 degrees C) were prepared. Lactic acid was copolymerized with 1,4:3,6-dianhydro-D-glucitol (isosorbide, ISB) and succinic acid (SA-2), 1,2,3,4-butanetetracarboxylic acid (BTCA-4) or 1,2,3,4,5,6-cyclohexanehexacarboxylic acid (HCA-6). The highest T(g)s obtained for the copolymers containing BTCA-4 and HCA-6 were 80 and 86 degrees C, respectively. The polymers were prepared by step-growth polymerization in the melt phase, which is an easily operable and simple PLA production method in comparison to the ring-opening polymerization (ROP) route. It was shown that the T(g) and the cross-linking induced by the polyfunctional carboxylic acid comonomers could be readily controlled by choosing a suitable polymerization time and temperature. Similar improvement in the T(g) as achieved for the copolymers of BTCA-4 and HCA-6 was not observed for linear copolymers containing ISB and SA-2.

Long-term evaluation of porous poly(epsilon-caprolactone-co-L-lactide) as a bone-filling material.

Porous poly(epsilon-caprolactone-co-L-lactide) (P(CL-co-LA, wt % ca. 5/95) sponges were prepared, coated biomimetically with CaP/apatite, and implanted with noncoated control sponges into rat femur cortical defects and dorsal subcutaneous space. The implants were inspected histologically at 2, 4, and 33 weeks after the operation. All implants were filled with fibrovascular tissue within 4 weeks. The femur implants were partially ossified with compact bone, which in the CaP-coated sponges was less mature and more fragmented. Approximately equal amounts of bone were observed in both types of implants. The polymer induced a mild inflammatory reaction with foreign body giant cells but no accumulation of fluid. Degradation of the polymer was slow; most of it was found intact at 33 weeks in histological samples. Nondegraded polymer seems to prevent complete ossification. Cultured osteoblasts proliferated well on apatite-coated material, whereas only a few cells were seen on noncoated material. Thus CaP/apatite coating helped the attachment of osteoblasts in cell cultures but did not offer any advantage in bone formation over noncoated material in vivo. We conclude that a shorter degradation time of P(CL-co-LA) is needed to create an optimal implant. Furthermore, in vivo experiments seem to be necessary for the estimation of osteopromotive properties of a biomaterial.