Efficacy of photobiomodulation using diode laser 650 nm combined with nano-cellulose and nano-amorphous calcium phosphate in bone healing of rabbit tibial defects assessed by H&E staining and computed tomography.

BACKGROUND: The purpose of the current study was to evaluate the effect of Diode LLLT 650 nm, TEMPO oxidized Nano-fibrillated cellulose mixed with Nano-Amorphous calcium phosphate, and their combination on bone healing in rabbit tibia using H&E staining and computed tomography. METHODS: Eighteen adult male New Zealand rabbits were selected, two circular bone defects were created in each tibia, resulting in four bony defects in each rabbit, representing the four tested groups; group A (negative control), group B (filled with mineralized nano-cellulose), group C (combination), group D (laser). Animals were euthanized after two weeks and one month, defects were assessed by CT for bone density, then histological samples were examined by H&E stain. RESULTS: In both evaluation periods, group D recorded the greatest mean area percent of new bone formation and bone density, followed by group A, while group C recorded the lowest value. Groups A and D showed full closure of the defects, while groups B and C showed partial defect closure with retained bone graft material. H&E and CT showed that Laser group had the best results of defects healing, bone density and new bone formation, followed by the negative control group. CONCLUSIONS: Diode laser 650nm photobiomodulation significantly improved bone defects healing. Mineralized nano-cellulose experimental bone substitute material showed a delayed effect in bone healing and graft material resorption. The combination of LLLT with the graft material had no positive outcome on bone defect healing.

EFFICACY OF HEMOSTATIC AGENTS IN ENDODONTIC SURGERY: A SYSTEMATIC REVIEW AND NETWORK META-ANALYSIS.

OBJECTIVE: Adequate hemostasis is a critical step in endodontic surgery. It facilitates the procedure and affects the success and prognosis of the operation. This systematic review and network meta-analysis (NMA) aimed to systematically assess the efficacy of hemostatic agents in endodontic surgery and to identify the most effective ones. METHODS: PubMed, Scopus, Embase, Cochrane Library, Web of Science, ProQuest, and EBSCOhost databases were searched up to December 2020. We included randomized controlled trials (RCTs) evaluating the efficacy of different hemostatic measures in endodontic surgery, and their risk of bias was assessed using Cochrane's randomized trial tool (RoB 2.0). Frequentist network meta-analysis was conducted, with Odds Ratios and 95% confidence intervals (OR, 95% CI) as effect estimates using the "netmeta" package in R. The quality of evidence was assessed using the CINeMA approach. RESULTS: Six RCTs involving 353 patients (mean age 48.12 y) were included. NMA revealed that aluminum chloride achieved higher hemostatic efficacy than epinephrine (OR = 2.55, 95% CI [1.41, 4.64]), while there was non-significant difference when compared with PTFE strips + epinephrine (OR = 1.00, 95% CI [0.35, 2.90]), electrocauterization (OR = 2.67, 95% CI [0.84, 8.46]), or ferric sulfate (OR = 8.65, 95% CI [0.31, 240.92]). Of all hemostatic agents, aluminum chloride ranked first in control bleeding during endodontic surgery (P-score = 0.84), followed by PTFE strips + epinephrine (P-score = 0.80), electrocauterization (P-score = 0.34), epinephrine (P-score = 0.34), ferric sulfate (P-score = 0.18). The quality of evidence was very low. CONCLUSIONS: Based on the limited data, aluminum chloride provides better hemostasis than epinephrine, while there was no significant difference between the remaining hemostatic agents used in endodontic surgery, which could help clinicians choose the hemostatic agent that achieves adequate hemostasis. achieve adequate hemostasis. Given insufficient evidence, future RCTs addressing this evidence gap are required.

The influence of different surface treatment protocols and bonding agents on the repair microtensile bond strength of six-month' aged composite: An in vitro study / A influência de diferentes protocolos de tratamento de superfície e agentes de união na resistência de união à microtração de reparo de compósito envelhecido por seis meses: um estudo in vitro

Objective: To compare the effect of three surface treatment protocols and two intermediate agents on repairing aged composite, regarding microtensile bond strength (µTBS) and mode of fracture, at two time intervals. Material and methods: Six-monthaged microhybrid composite blocks, were randomly distributed into three groups, subjected to; Fine, Super Fine grit diamond burs or Erbium- Yag Laser surface treatment. Each block had both One Coat bond SL (Bond) and Brilliant Flow flowable composite (Flow) intermediate agents, alongside. Blocks were incrementally repaired using nanohybrid composite, cut into beams, then randomly subjected either immediately (IM) to µTBS test or after thermocycling (TC) for 5000 cycle. Mode of failure was determined using stereomicroscope. Data were analyzed through three-way ANOVA followed by pairwise comparison with Bonferroni correction. Kruskal Wallis test compared groups for failure mode analysis (α=0.05) Results: Super Fine grit showed the highest mean µTBScompared to control for both intermediate agents, IM and after TC at P<0.05. No difference between Fine grit and Laser application for all groups (P>0.05). IM, Bond showed the highest µTBS compared to TC, Flow for all tested groups. Beams roughened with Fine and Super Fine burs showed significantly lower adhesive failures than those roughened with Laser. Flow suffers significantly higher adhesive failure than those with Bond. For TC tested groups; beams with Super Fine bur and Bond showed significantly lower adhesive failure at P=0.029. Conclusion: Super Fine grit and Bond provide the highest µTBS and the least adhesive failure; moreover TC resulted in significant decrease in µTBS (AU)

Objetivo: Comparar o efeito de três protocolos de tratamento de superfície e dois agentes intermediários no reparo de compósito envelhecido, quanto à resistência à microtração (µTBS) e modo de fratura, em dois intervalos de tempo. Material e métodos: Blocos de compósito microhíbrido envelhecidos por seis meses, foram distribuídos aleatoriamente em três grupos, submetidos a; Pontas diamantadas de granulação Fina, Superfina ou tratamento de superfície com laser de Erbio-Yag. Cada bloco tinha ambos os agentes intermediários One Coat bond SL (Adesivo) ao lado de Brilliant Flow (Resina Fluida). Os blocos foram reparados de forma incremental usando compósito nanohíbrido, cortados em palitose, em seguida, submetidos aleatoriamente imediatamente (IM) ao teste de µTBS ou após termociclagem (TC) por 5000 ciclos. O modo de falha foi determinado usando estereomicroscópio. Os dados foram analisados por meio de ANOVA de três fatores, seguida de comparação pareada com correção de Bonferroni. O teste de Kruskal Wallis comparou os grupos para análise do modo de falha (α = 0,05). Resultados: a granulação Super fina apresentou a maior média de µTBS em comparação com o controle para ambos os agentes intermediários, IM e após TC (P <0,05). Não houve diferença entre granulação fina e aplicação de laser para todos os grupos (P> 0,05). IM, Adesivo apresentou a µTBS mais alta em comparação com TC, Resina Fluida para todos os grupos testados. Os palitos asperizados com pontas de granulações Fina e Superfina apresentaram falhas adesivas significativamente menores do que as asperizadas com Laser. Resina Fluida sofreu falhas adesivas significativamente maiores do que aquelas com Adesivo. Para grupos testados TC; palitos tratados com ponta Superfina e Adesivo apresentaram falha adesiva significativamente menor com P = 0,029. Conclusão: a granulação Superfina e o Adesivo fornecem a maior µTBS e o mínimo de falha adesiva; além disso, o TC resultou em uma diminuição significativa da µTBS. (AU)

In-vitro and in-vivo, cytotoxicity evaluation of cast functionally graded biomaterials for dental implantology.

An innovative technique of casting the titanium implant alloys and its calcium phosphate coating using centrifugal casting method was proposed in the current study. This one-step, self-coating technique results in formation of functionally graded biomaterials (FGBMs) of calcium phosphate/Titanium alloys. Two groups of samples (Group 1 and Group 2) were prepared utilizing self-coated titanium­niobium (Ti-6Al-7Nb) and titanium- vanadium (Ti-6Al-4V) alloys respectively. The cast samples were then prepared for in-vitro cytocompatibility evaluation, in-vivo systemic toxicity and osseointegration evaluation. Cytocompatibility was examined in-vitro on human bone osteosarcoma cells (Saos-2). In-vivo surgical implantation of the samples in the mandible of the experimental dogs was correspondingly implemented. Tests for systemic toxicity, X-ray images, Dual Energy X-ray Absorptiometry (DEXA) and histopathological analysis were obtained for each dog's mandible sample. In-vitro cytocompatibility studies revealed high cytocompatibility of Group 2 in comparison to Group 1. In-vivo results proved safety of Group 2 as regards to systemic toxicity. On the other hand, results of the X-ray images, DEXA and histopathological analysis revealed comparable osseointegration potential of both groups. These results suggest the use of Group2-FGBMs in dental implant manufacturing and prove that FGBMs prepared by centrifugal casting as self-coated implants have good biocompatibility and osseointegration capability.