Mass-Producible 2D Nanocomposite-Based Temperature-Independent All-Printed Relative Humidity Sensor.

Relative humidity sensors are widely studied under the categories of both environmental and biosensors owing to their vast reaching applications. The research on humidity sensors is mainly divided into two concentration areas including novel material development and novel device structure. Another approach focuses on the development of printed sensors with performance comparable to the sensors fabricated via conventional techniques. The major challenges in the research on relative humidity sensors include the range of detection, sensitivity (especially at lower %RH), transient response time, and dependence on temperature. Temperature dependence is one of the least studied parameters in relative humidity sensor development. In this work, relative humidity sensors were fabricated using all-printed approaches that are also compatible with mass production, resulting in low cost and easy development. Laser-induced graphene (LIG)-based printed electrodes were used as the transducers, while the 2D MoS2 and graphene nanocomposite was used as the active layer material with the built-in property of temperature independence. The exfoliation process of 2D MoS2 was based on wet grinding, while graphene for the active layer was obtained by scratching the graphene grown on the polyimide (PI) surface via laser ablation. The resulting sensors showed an excellent output response for a full range of 0%RH to 100%RH, having no dependence on the surrounding temperature, and excellent response and recovery times of 4 and 2 s, respectively. The developed sensors can be confidently employed for a wide range of humidity sensing applications where the temperature of the surrounding environment is not constant.

A fluorescent lateral flow biosensor for the quantitative detection of Vaspin using upconverting nanoparticles.

Vaspin is a protein present in human serum that can cause type-2 diabetes, obesity, and other cardiovascular diseases. We report fluorescent upconverting nanoparticles (UCNPs)-based lateral flow biosensor for ultrasensitive detection of Vaspin. A pair (primary and secondary) of cognate aptamers was used that has duo binding with Vaspin. UCNPs with a diameter of around 100 nm were used as a tag to label a detection probe (secondary aptamer). A primary aptamer (capture probe) was immobilized on the test zone. Sandwich type hybridization reactions among the conjugate probe, target Vaspin, and primary aptamer were performed on the lateral flow biosensor. In the presence of target Vaspin, UCNPs were captured on the test zone of the biosensor and the fluorescent intensity of the captured UCNPs was measured through a colorimetric app under NIR. Fluorescence intensity indicates the quantity of Vaspin present in the sample. A range of Vaspin concentration across 0.1-55 ng ml-1 with a Limit of detection (LOD) 39 pg ml-1 was tested through this UCNPs based LFSA with high sensitivity, reproducibility and repeatability, whereas it's actual range in human blood is from 0.1 to 7 ng ml-1. Therefore, this research provides a well-suited lateral flow strip with an ultrasensitive and low-cost approach for the early diagnosis of type-2 diabetes and this could be applied to any targets with a duo of aptamers generated.

Highly Sensitive and Full Range Detectable Humidity Sensor using PEDOT:PSS, Methyl Red and Graphene Oxide Materials.

Single transducer with humidity sensing materials has limitations in both range and sensitivity, which cannot be used to detect the full range of humidity with consistent sensitivity. To enlarge range and improve sensitivity in the all range relative humidity (RH), we propose a highly sensitive and full range detectable humidity sensor based on multiple inter-digital transducer (IDT) electrodes connected in series with poly(3,4-ethylenedioxythiophene) doped poly (styrene sulfonate) anions (PEDOT: PSS), C15H15N3O2 (Methyl Red), and graphene oxide (GO) thin films as the active sensing materials. The humidity sensor with single active material has a limit in the detecting ranges, where the GO, PEDOT: PSS, and Methyl Red materials have sensing responses of 0 to 78% RH, 30 to 75% RH, and 25 to 100% RH, respectively. However, a humidity sensor using combined three active materials can respond to much wider range of RH with high sensitivity, where the IDTs and the active regions were prepared using ink-jet printing and spin coating, respectively. This proposed sensor can detect a full range of 0% RH to 100% RH. The response and recovery times are 1 sec and 3.5 sec, respectively. Our single sensing device using multiple IDTs connected different active materials in series can overcome the limitations of single transducer based sensor for the high performance sensor applications.

3D printing for soft robotics - a review.

Soft robots have received an increasing attention due to their advantages of high flexibility and safety for human operators but the fabrication is a challenge. Recently, 3D printing has been used as a key technology to fabricate soft robots because of high quality and printing multiple materials at the same time. Functional soft materials are particularly well suited for soft robotics due to a wide range of stimulants and sensitive demonstration of large deformations, high motion complexities and varied multi-functionalities. This review comprises a detailed survey of 3D printing in soft robotics. The development of key 3D printing technologies and new materials along with composites for soft robotic applications is investigated. A brief summary of 3D-printed soft devices suitable for medical to industrial applications is also included. The growing research on both 3D printing and soft robotics needs a summary of the major reported studies and the authors believe that this review article serves the purpose.

All-printed highly sensitive 2D MoS2 based multi-reagent immunosensor for smartphone based point-of-care diagnosis.

Immunosensors are used to detect the presence of certain bio-reagents mostly targeted at the diagnosis of a condition or a disease. Here, a general purpose electrical immunosensor has been fabricated for the quantitative detection of multiple bio-reagents through the formation of an antibody-antigen pair. The sensors were fabricated using all printing approaches. 2D transition metal dichalcogenide (TMDC) MoS2 thin film was deposited using Electrohydrodynamic atomization (EHDA) on top of an interdigitated transducer (IDT) electrode fabricated by reverse offset printing. The sensors were then treated with three different types of antibodies that were immobilized by physisorption into the highly porous multi-layered structure of MoS2 active layer. BSA was used as blocking agent to prevent non-specific absorption (NSA). The sensors were then employed for the targeted detection of the specific antigens including prostate specific antigen (PSA), mouse immunoglobulin-G (IgG), and nuclear factor kappa-light-chain-enhancer of activated B cells (NF-κB). IgG was then selected to test the sensors for point of care (POC) diagnosis through a specially designed electronic readout system for sensors and interfacing it with a smartphone using Bluetooth connection. The sensors showed promising performance in terms of stability, specificity, repeatability, sensitivity, limit of detection (LoD), and range of detection (RoD).

Bio-compatible organic humidity sensor transferred to arbitrary surfaces fabricated using single-cell-thick onion membrane as both the substrate and sensing layer.

A bio-compatible disposable organic humidity sensor has been fabricated that can be transferred to any arbitrary target surface. Single cell thick onion membrane has been used as the substrate while it also doubles as the active layer of the sensor. Two different types of sensors were fabricated. In type-1, the membrane was fixed into a plastic frame with IDT patterns on one side while the other side was also exposed to environment. In type-2, onion membrane was attached to a glass substrate with one side exposed to environment having an IDT screen-printed on top of it. The electrical output response of the sensors showed their ability to detect relative humidity between 0% RH and 80% RH with stable response and good sensitivity. The impedance of the sensors changed from 16 MΩ to 2 MΩ for type-1 and 6 MΩ to 20 KΩ for type-2. The response times of type-1 and type-2 were ~1 and 1.5 seconds respectively. The recovery times were ~10.75 seconds and ~11.25 seconds for type-1 and type-2 respectively. The device was successfully transferred to various randomly shaped surfaces without damaging the device.

Hybrid Surface Acoustic Wave-Electrohydrodynamic Atomization (SAW-EHDA) For the Development of Functional Thin Films.

Conventional surface acoustic wave - electrostatic deposition (SAW-ED) technology is struggling to compete with other thin film fabrication technologies because of its limitation in atomizing high density solutions or solutions with strong inter-particle bonding that requires very high frequency (100 MHz) and power. In this study, a hybrid surface acoustic wave - electrohydrodynamic atomization (SAW-EHDA) system has been introduced to overcome this problem by integrating EHDA with SAW to achieve the deposition of different types of conductive inks at lower frequency (19.8 MHZ) and power. Three materials, Poly [2-methoxy-5-(2-ethylhexyloxy)-1, 4-phenylenevinylene] (MEH-PPV), Zinc Oxide (ZnO), and Poly(3, 4-ethylenedioxythiophene):Polystyrene Sulfonate ( PEDOT: PSS) have been successfully deposited as thin films through the hybrid SAW-EHDA. The films showed good morphological, chemical, electrical, and optical characteristics. To further evaluate the characteristics of deposited films, a humidity sensor was fabricated with active layer of PEDOT: PSS deposited using the SAW-EHDA system. The response of sensor was outstanding and much better when compared to similar sensors fabricated using other manufacturing techniques. The results of the device and the films' characteristics suggest that the hybrid SAW-EHDA technology has high potential to efficiently produce wide variety of thin films and thus predict its promising future in certain areas of printed electronics.