Energy Absorption and Beam Damage during Microfocus Synchrotron X-ray Diffraction.

In this study, we combine in situ fast differential scanning calorimetry (FDSC) with synchrotron X-ray measurements to study simultaneously the structure and thermophysical properties of materials. Using the example of the organic compound BCH-52, we show that the X-ray beam can heat the sample and induce a shift of the heat-flow signal. The aim of this paper is to investigate the influence of radiation on sample behavior. The calorimetric data is used to quantify the absorbed beam energy and, together with the diffraction data, reveal an irreversible damage of the sample. The results are especially important for materials with high absorption coefficients and for high-energy X-ray and electron beams. Our findings illustrate that FDSC combined with X-ray diffraction is a suitable characterization method when beam damage must be minimized.

Influence of Chemical Composition and Structure on the Cooperative Fluctuation in Supercooled Glass-Forming Liquids.

The kinetics of the glass transition and the characteristic size of the fluctuating spatio-temporal domains in supercooled glass-forming liquids, i.e., the Cooperatively Rearranging Regions (CRR), were measured upon cooling over a broad range of cooling rates using Differential Scanning Calorimetry (DSC) and chip-based Fast Scanning Calorimetry (FSC). The investigations were conducted on a selection of fragile glass formers (fragility indices between 80 and 140), with a large variance in the atomic or molecular structure but comparable thermal glass transition temperatures Tg, with the aim of evaluating the influence of chemical composition and structure on the CRR size and the associated temperature fluctuation. The selected materials are two polymers (poly(vinyl acetate) (PVAc), poly(lactic acid) (PLA)) as well as the simplest chalcogenide glass-former (selenium). It turned out that the CRR size plotted against the reduced temperature T/Tg follows the same trend, irrespective of the considered glass-former.

Effect of water on the glass transition of a potassium-magnesium carbonate melt.

Calorimetric measurements of the glass transition temperatures (Tg) of hydrous carbonate melts are reported on a near-eutectic composition of 55 mol% K2CO3 - 45 mol% MgCO3 with up to 42 mol% bulk H2O dissolved in the carbonate melt. Hydrous melts were quenched from 750°C to transparent and crystal-free glasses and were subsequently analysed for water content before and after measuring Tg by high-sensitivity differential scanning calorimetry. The glass transition and limited fictive temperatures as a function of the water content were determined at 10 K/min cooling/heating rates resulting in Tg ranging from 245°C at nominally anhydrous conditions to 83°C in the presence of 42 mol% H2O in the glass. Through a generalized Gordon-Taylor analysis, the factors k (7.27), k0 (3.2) and the interaction parameter Ax (0.49) were derived. The limited fictive temperature of a hypothetically, zero water containing 55 mol% K2CO3 - 45 mol% MgCO3 glass is 232 ± 5°C (505 K). The high value of the interaction parameter A indicates strong specific molecular interactions between water and the carbonates in the glassy state and a large decrease in the excess enthalpy of mixing during the conversion of the glassy into the liquid state at the glass transition. This article is part of the theme issue 'Exploring the length scales, timescales and chemistry of challenging materials (Part 1)'.

Glass transition temperatures and crystallization kinetics of a synthetic, anhydrous, amorphous calcium-magnesium carbonate.

We report the first calorimetric observations of glass transition temperatures and crystallization rates of anhydrous, amorphous calcium-magnesium carbonate using fast scanning differential scanning calorimetry. Hydrous amorphous Ca0.95Mg0.05CO3 · 0.5H2O (ACMC) solid was precipitated from a MgCl2-NaHCO3 buffered solution, separated from the supernatant, and freeze-dried. An aliquot of the freeze-dried samples was additionally dried at 250°C for up to 6 h in a furnace and in a high-purity N2 atmosphere to produce anhydrous ACMC. The glass transition temperature of the anhydrous Ca0.95Mg0.05CO3 was determined by applying different heating rates (1000-6000 K s-1) and correcting for thermal lag to be 376°C and the relaxational heat capacity was determined to be Cp = 0.16 J/(g K). Additionally, the heating rate dependence of the temperature that is associated with the corrected crystallization peaks is used to determine the activation energy of crystallization to be 275 kJ mol-1. A high-resolution transmission electron microscopy study on the hydrous and anhydrous samples provided further constraints on their compositional and structural states. This article is part of the theme issue 'Exploring the length scales, timescales and chemistry of challenging materials (Part 1)'.

Fast differential scanning calorimetry to mimic additive manufacturing processing: specific heat capacity analysis of aluminium alloys.

Eutectic AlSi12, commonly used in casting and in additive manufacturing, is investigated with Fast Differential Scanning Calorimetry to determine the impact of different cooling rates from the liquid state upon the apparent specific heat capacity on subsequent heating. A heat flow correction strategy is developed and refined for the reliable and precise measurement of sample heat flow using chip sensors and assessed by the evaluation of results on pure (99.999%) aluminium. That strategy is then applied to the study of the AlSi12 eutectic alloy, and rate-dependent perturbations in the measured apparent specific heat capacity are discussed in terms of Si supersaturation and precipitation. Several cooling rates were implemented from - 100 to - 30,000 K s-1, and subsequent heating ranged from + 1000 to + 30,000 K s-1. After rapid cooling, a drop in AlSi12 apparent specific heat capacity is found on heating above ~ 400 °C; even at rates of + 10,000 K s-1, a result which has high relevance in metal additive manufacturing where similarly fast temperature cycles are involved. The Literature data, temperature modulated DSC and CALPHAD simulations on the heat capacity of AlSi12 are used to provide comparative context to the results from Fast Differential Scanning Calorimetry.

Kinetics of the Glass Transition of Silica-Filled Styrene-Butadiene Rubber: The Effect of Resins.

Resins are important for enhancing both the processability and performance of rubber. Their efficient utilization requires knowledge about their influence on the dynamic glass transition and their miscibility behavior in the specific rubber compound. The resins investigated, poly-(α-methylstyrene) (AMS) and indene-coumarone (IC), differ in molecular rigidity but have a similar aromaticity degree and glass transition temperature. Transmission electron microscopy (TEM) investigations show an accumulation of IC around the silanized silica in styrene-butadiene rubber (SBR) at high contents, while AMS does not show this effect. This higher affinity between IC and the silica surface leads to an increased compactness of the filler network, as determined by dynamic mechanical analysis (DMA). The influence of the resin content on the glass transition of the rubber compounds is evaluated in the sense of the Gordon-Taylor equation and suggests a rigid amorphous fraction for the accumulated IC. Broadband dielectric spectroscopy (BDS) and fast differential scanning calorimetry (FDSC) are applied for the characterization of the dielectric and thermal relaxations as well as for the corresponding vitrification kinetics. The cooling rate dependence of the vitrification process is combined with the thermal and dielectric relaxation time by one single Vogel-Fulcher-Tammann-Hesse equation, showing an increased fragility of the rubber containing AMS.

Structural relaxation in layered, non-stoichiometric Fe7S8.

In this study, we investigate the kinetics of the enantiotropic solid-solid ß-transition in Fe7S8 pyrrhotite, which presents a prominent example of a metal-nonmetal compound with layered crystal structure. The low-temperature (4C) and high-temperature (1C) modifications differ in their crystallographic unit-cell dimension, vacancy distribution, and magnetic ordering in the crystal lattice. Fast differential scanning calorimetry (FDSC) reveals that cooling of the paramagnetic 1C phase below the transformation temperature Tß = 597 K, which is also the Curie temperature, generates a metastable phase that transforms into the ferrimagnetic 4C phase with high vacancy order upon further annealing below Tß. Upon fast cooling, the low-temperature modification shows an energetically excited phase with higher entropy that relaxes towards the equilibrated pyrrhotite polymorph. The kinetics of the superheating and the structural relaxation as obtained from FDSC experiments provide deeper insight into the stability of Fe7S8 polymorphs. This may pave a new path to decipher in detail the kinetics of solid-solid phase transformations and the long-term lifespan of defects in Earth and synthetic materials.

Competition between Structural Relaxation and Crystallization in the Glass Transition Range of Random Copolymers.

Structural relaxation in polymers occurs at temperatures in the glass transition range and below. At these temperatures, crystallization is controlled by diffusion and nucleation. A sequential occurrence of structural relaxation, nucleation, and crystallization was observed for several homopolymers during annealing in the range of the glass transition. It is known from the literature that all of these processes are strongly influenced by geometrical confinements. The focus of our work is copolymers, in which the confinements are caused by the random sequence of monomer units in the polymer chain. We characterize the influence of these confinements on structure formation and relaxation in the vicinity of the glass transition. The measurements were performed with a hydrogenated nitrile-butadiene copolymer (HNBR). The kinetics of the structural relaxation and the crystallization was measured using fast differential scanning calorimetry (FDSC). This technique was selected because of the high sensitivity, the fast cooling rates, and the high time resolution. Crystallization in HNBR causes a segregation of non-crystallizable segments in the macromolecule. This yields a reduction in mobility in the vicinity of the formed crystals and as a consequence an increased amount of so-called "rigid amorphous fraction" (RAF). The RAF can be interpreted as self-assembled confinements, which limit and control the crystallization. An analysis of the crystallization and the relaxation shows that the kinetic of both is identical. This means that the Kohlrausch exponent of relaxation and the Avrami exponent of crystallization are identical. Therefore, the crystallization is not controlled by nucleation but by diffusion and is terminated by the formation of RAF.

Existence of multiple critical cooling rates which generate different types of monolithic metallic glass.

Via fast differential scanning calorimetry using an Au-based glass as an example, we show that metallic glasses should be classified into two types of amorphous/monolithic glass. The first type, termed self-doped glass (SDG), forms quenched-in nuclei or nucleation precursors upon cooling, whereas in the so-called chemically homogeneous glass (CHG) no quenched-in structures are found. For the Au-based glass investigated, the critical cooling and heating rates for the SDG are 500 K s-1 and 20,000 K s-1, respectively; for the CHG they are 4000 K s-1 and 6000 K s-1. The similarity in the critical rates for CHG, so far not reported in literature, and CHG's tendency towards stochastic nucleation underline the novelty of this glass state. Identifying different types of metallic glass, as is possible by advanced chip calorimetry, and comparing them with molecular and polymeric systems may help to elaborate a more generalized glass theory and improve metallic glass processing.

Vitrification in a wide cooling rate range: the relations between cooling rate, relaxation time, transition width, and fragility.

The cooling rate dependence of the thermal glass transition of polystyrene (PS) is measured in a range between 0.2 K/min (0.003 K/s) and 4000 K/s using conventional differential scanning calorimetry (DSC) and Fast Scanning Calorimetry (Flash DSC 1). The cooling rate dependence of the thermal glass transition can be described in an analogy to the frequency dependence of the dynamic glass transition. The relation between cooling rate, ß(c), and frequency, ω, is usually described by the Frenkel-Kobeko-Reiner-(FKR) hypothesis ß(c)/ω = C, where C is a constant. We have introduced a new property to describe the kinetics of the vitrification process; the vitrification function, κ. This function is the ratio between the width of the thermal and dynamic glass transition. The validity of the FKR hypothesis is analyzed by two independent methods, the analysis of the activation diagram using the Vogel-Fulcher-Tammann-Hesse equation and the analysis of the temperature dependence of the transition width. We derived a relation for the FKR-constant, which indicates the validity range of the FKR hypotheses. This hypothesis is valid if the logarithmic width of the vitrified and the non-vitrified relaxation spectrum is temperature invariant. This condition is fulfilled for polystyrene in the measured cooling rate range. Furthermore we discuss the relation between the vitrification function, the transition width, the FKR constant, and the fragility.