Effect of titanium surface roughness on proliferation, differentiation, and protein synthesis of human osteoblast-like cells (MG63).

The effect of surface roughness on osteoblast proliferation, differentiation, and protein synthesis was examined. Human osteoblast-like cells (MG63) were cultured on titanium (Ti) disks that had been prepared by one of five different treatment regimens. All disks were pretreated with hydrofluroic acid-nitric acid and washed (PT). PT disks were also: washed, and then electropolished (EP); fine sandblasted, etched with HCl and H2SO4, and washed (FA); coarse sandblasted, etched with HCl and H2SO4, and washed (CA); or Ti plasma-sprayed (TPS). Standard tissue culture plastic was used as a control. Surface topography and profile were evaluated by brightfield and darkfield microscopy, cold field emission scanning electron microscopy, and laser confocal microscopy, while chemical composition was mapped using energy dispersion X-ray analysis and elemental distribution determined using Auger electron spectroscopy. The effect of surface roughness on the cells was evaluated by measuring cell number, [3H]thymidine incorporation into DNA, alkaline phosphatase specific activity, [3H]uridine incorporation into RNA, [3H]proline incorporation into collagenase digestible protein (CDP) and noncollagenase-digestible protein (NCP), and [35S]sulfate incorporation into proteoglycan. Based on surface analysis, the five different Ti surfaces were ranked in order of smoothest to roughest: EP, PT, FA, CA, and TPS. A TiO2 layer was found on all surfaces that ranged in thickness from 100 A in the smoothest group to 300 A in the roughest. When compared to confluent cultures of cells on plastic, the number of cells was reduced on the TPS surfaces and increased on the EP surfaces, while the number of cells on the other surfaces was equivalent to plastic. [3H]Thymidine incorporation was inversely related to surface roughness. Alkaline phosphatase specific activity in isolated cells was found to decrease with increasing surface roughness, except for those cells cultured on CA. In contrast, enzyme activity in the cell layer was only decreased in cultures grown on FA- and TPS-treated surfaces. A direct correlation between surface roughness and RNA and CDP production was found. Surface roughness had no apparent effect on NCP production. Proteoglycan synthesis by the cells was inhibited on all the surfaces studied, with the largest inhibition observed in the CA and EP groups. These results demonstrate that surface roughness alters osteoblast proliferation, differentiation, and matrix production in vitro. The results also suggest that implant surface roughness may play a role in determining phenotypic expression of cells in vivo.

Demonstration of a focused ion-beam cross-sectioning technique for ultrastructural examination of resin-dentin interfaces.

OBJECTIVES: focused ion-beam (FIB) etching, commonly used as a cross-sectioning technique for failure analysis of semiconductor devices, has recently been applied to biological tissues to expose their ultrastructure for examination. It was the aim of this investigation to determine the practical utility of FIB to cross-section resin-dentin interfaces in order to morphologically evaluate the completeness of resin penetration into the exposed collagen scaffold at the resin-dentin bond interface. METHODS: Two representative commercially available dentin adhesive systems were bonded to mid-coronal dentin. After appropriate fixation and dehydration of the resin-bonded dentin samples, a scanned focused ion-beam of a few tens of nano-meters in diameter was used to cross=section the resin-dentin interface. Examination of the interfacial ultrastructure was accomplished using a field-emission SEM. RESULTS: Results indicate possible artifact production at the cross-sectioned interface, hiding its actual ultrastructure, probably due to a heat-effect with possible recrystallization. Further studies of FIB are needed to optimize its usefulness for resin-dentin interface examinations and other biological tissue applications. SIGNIFICANCE: Complete resin saturation of the demineralized dentin surface-layer has been claimed to be the key factor for a long-lasting resin-dentin bond. A "clean" artifact-free micro-cross-sectioning technique may provide indisputable ultra-structural information about the depth of resin penetration into the demineralized zone. Such a test would be useful in the development of dentin adhesive systems.