Bond Strength of Milled and Printed Zirconia to 10-Methacryloyloxydecyl Dihydrogen Phosphate (10-MDP) Resin Cement as a Function of Ceramic Conditioning, Disinfection and Ageing.

This study aimed to assess the suitability of printed zirconia (ZrO2) for adhesive cementation compared to milled ZrO2. Surface conditioning protocols and disinfection effects on bond strength were also investigated. ZrO2 discs (n = 14/group) underwent either alumina (Al2O3) airborne particle abrasion (APA; 50 µm, 0.10 MPa) or tribochemical silicatisation (TSC; 110 µm Al2O3, 0.28 MPa and 110 µm silica-modified Al2O3, 0.28 MPa), followed by disinfection (1 min immersion in 70% isopropanol, 15 s water spray, 10 s drying with oil-free air) for half of the discs. A resin cement containing 10-methacryloyloxydecyl dihydrogen phosphate (10-MDP) was used for bonding (for TSC specimens after application of a primer containing silane and 10-MDP). Tensile bond strength was measured after storage for 24 h at 100% relative humidity or after 30 days in water, including 7500 thermocycles. Surface conditioning significantly affected bond strength, with higher values for TSC specimens. Ageing and the interaction of conditioning, disinfection and ageing also impacted bond strength. Disinfection combined with APA mitigated ageing-related bond strength decrease but exacerbated it for TSC specimens. Despite these effects, high bond strengths were maintained even after disinfection and ageing. Adhesive cementation of printed ZrO2 restorations exhibited comparable bond strengths to milled ZrO2, highlighting its feasibility in clinical applications.

Load-bearing capacity of 3D-printed incisor partial-coverage crowns made from zirconia and composite.

PURPOSE: This study investigated the fracture resistance of 0.5-mm-thick restorations for minimally invasive therapy. Anterior partial-coverage crowns composed of three-dimensional (3D)-printed 3-mol% yttria-stabilized tetragonal zirconia polycrystal (3Y-TZP; Lithacon 3Y210, Lithoz) and 3D-printed composite (Varseo Smile Crown plus, Bego) were compared with a control group made from milled 3Y-TZP (Cercon ht, DentsplySirona). METHODS: Three groups each with 27 restorations were produced. For milled 3Y-TZP partial-coverage crowns, drill compensation was needed so the milling bur could access the inner surface at the incisal edge. Restoration fit was verified by cross-sectioning 12 specimens in each group. The remaining 15 restorations were sandblasted (Al2O3, 0.1 MPa) and adhesively cemented (Panavia SA, Kuraray) onto CoCr teeth. Static load-to-failure tests were performed. The load was induced on the incisal edge. The forces needed to fracture the specimens were analyzed using the Welch analysis of variance and post hoc Dunnet-T3 tests. The Weibull parameters were also calculated. RESULTS: Drill compensation increased cement thickness at the loading area by 200 µm in milled 3Y-TZP restorations compared with the 3D-printed partial-coverage crowns. Fracture resistance was the highest in 3D-printed 3Y-TZP restorations (1570±661N) followed by milled 3Y-TZP (886±164N) and 3D-printed composite partial-coverage crowns (570±233 N). Milled 3Y-TZP was associated with a substantially higher Weibull modulus (m=6) than the 3D-printed materials (m=2), suggesting greater reliability. CONCLUSIONS: Fracture resistance increased with tighter fit, demonstrating the benefit of the geometric freedom associated with 3D-printing. Future research should focus on making 3D-printed 3Y-TZP more reliable to increase its safety in clinical use.

Effect of firing time and wall thickness on the biaxial flexural strength of 3D-printed zirconia.

OBJECTIVES: To evaluate the effect of accelerated firing on 3D-printed zirconia. METHODS: To check if formulae provided by ISO 6872 can be extended to thin samples, finite element analyses were carried out in advance of fabricating 3-mol% yttria-stabilized tetragonal zirconia polycrystal discs by milling and by 3D-printing. Four groups (n = 38 each) of 3D-printed specimens were produced with two nominal thicknesses (0.6 mm and 1.2 mm) and two firing strategies (long: 51 h, accelerated: 14.5 h). In the milled group (thickness 1.2 mm, n = 30), a standard firing program (9.8 h) was selected. Biaxial flexural strength tests were applied and mean strength, characteristic strength, and Weibull modulus were calculated for each group. Differences were analyzed using Welch ANOVA and Dunnett-T3 post-hoc tests. RESULTS: Maximum tensile stresses occurring during biaxial strength testing can be calculated according to ISO 6872 for thin samples with b > 0.3 mm. Variability of measured strengths values was smaller for milled zirconia compared with 3D-printed zirconia. The 1.2-mm-thick 3D-printed samples had significantly decreased strength after accelerated firing than after long firing. However, for the 0.6-mm-thick samples, comparable mean biaxial strength values of about 1000 MPa were measured for both firing protocols. SIGNIFICANCE: At the moment, long fabrication time for zirconia restorations is a major drawback of 3D-printing when compared with milling technology. This investigation showed that the strength of 0.6-mm-thick zirconia discs fabricated by 3D-printing was not impaired by accelerated firing. Thus, overnight firing of thin-walled 3D-printed zirconia restorations could be possible.

Fit and Retention of Cobalt-Chromium Removable Partial Denture Frameworks Fabricated with Selective Laser Melting.

PURPOSE: To evaluate fit and retention of cobalt-chromium removable partial denture (RPD) frameworks fabricated with selective laser melting (SLM). METHODS: Three types of framework for clasp-retained RPDs were virtually designed and fabricated using SLM (n = 30). For comparison, 30 additional frameworks were produced using conventional lost-wax casting. A biomechanical model was created, incorporating extracted teeth mounted on flexible metal posts. Using this model, horizontal constraint forces resulting from a misfit were measured using strain gauges, while vertical forces were not recorded. The constraint force components and resultant forces were determined for all abutment teeth, and the maximum retention force during RPD removal from the model was also assessed. For statistical evaluation, the two fabrication methods were analyzed by calculating the means and standard deviations. RESULTS: The average horizontal constraint forces showed similar values for both fabrication methods (SLM: 3.5 ± 1.0 N, casting: 3.4 ± 1.6 N). The overall scatter of data for cast RPDs was greater compared to those fabricated using SLM, indicating a better reproducibility of the SLM process. With regard to retention, the intended retention force of 5-10 N per abutment tooth was not attained in one of the cast groups, while it was consistently achieved in all SLM groups. CONCLUSIONS: This in vitro study found that SLM is a promising option for the manufacture of cobalt-chromium RPD frameworks in terms of fit and retention.

Oral Sequelae after Head and Neck Radiotherapy: RCT Comparing 3D-Printed Tissue Retraction Devices with Conventional Dental Splints.

OBJECTIVES: To evaluate oral sequelae after head and neck radiotherapy (RT) when using two different types of intraoral appliances. Thermoplastic dental splints (active control) protect against backscattered radiation from dental structures. Semi-individualized, 3D-printed tissue retraction devices (TRDs, study group) additionally spare healthy tissue from irradiation. MATERIALS AND METHODS: A total of 29 patients with head and neck cancer were enrolled in a randomized controlled pilot trial and allocated to receive TRDs (n = 15) or conventional splints (n = 14). Saliva quality and quantity (Saliva-Check, GC), taste perception (Taste strips, Burghart-Messtechnik), and oral disability (JFLS-8, OHIP-14, maximum mouth opening) were recorded before and 3 months after RT start. Radiotherapy target volume, modality, total dose, fractionation, and imaging guidance were case-dependent. To evaluate intra-group developments between baseline and follow-up, nonparametric Wilcoxon tests were performed. Mann-Whitney-U tests were applied for inter-group comparisons. RESULTS: At follow-up, taste perception was unimpaired (median difference in the total score; TRDs: 0, control: 0). No significant changes were found regarding oral disability. Saliva quantity (stimulated flow) was significantly reduced with conventional splints (median -4 mL, p = 0.016), while it decreased insignificantly with TRDs (median -2 mL, p = 0.07). Follow-up was attended by 9/15 study group participants (control 13/14). Inter-group comparisons showed no significant differences but a tendency towards a better outcome for disability and saliva quality in the intervention group. CONCLUSION: Due to the small cohort size and the heterogeneity of the sample, the results must be interpreted with reservation. Further research must confirm the positive trends of TRD application. Negative side-effects of TRD application seem improbable.

Thermo-flexible resin for the 3D printing of occlusal splints: A randomized pilot trial.

OBJECTIVES: To compare the clinical performance of occlusal splints printed from thermo-flexible resin with milled splints. METHODS: A parallel two-arm pilot trial was initiated. Forty-seven patients (n women=38) were recruited from a tertiary care center and randomized using an online tool (sealed envelope). Inclusion criterion was an indication for treatment with a centric relation occlusal splint due to bruxism or any form of painful temporomandibular disorder. Patients were excluded if they were younger than 18 years, unable to attend follow-up appointments, or required another type of splint therapy. Patients received either, a 3D-printed (intervention group, V-print splint comfort, VOCO) or a milled splint (control group, ProArt CAD splint, Ivoclar). Construction software Ceramill M-splint (AmannGirrbach), 3D-printer MAX UV 385 (Asiga) and milling unit PrograMill PM7 (Ivoclar) were used. Follow-up assessments were conducted after 2 weeks and 3 months. Outcome measures were survival, adherence, technical complications, patient satisfaction on a 10-point Likert scale, and maximum wear using superimposition of optical scans. RESULTS: After 3 months, 20/23 intervention group and 18/24 control group participants were assessed. All splints survived. Minor complications were small crack formations on 6 printed and 4 milled splints. Mean patient satisfaction was 8 (SD 1.7) for printed, and 8.1 (SD 2.3) for milled splints (r = 0.1, p = .52). Median maximum wear was highly dispersed with 153 (IQR 140) in posterior and 195 (IQR 537) in frontal segments of printed, and 96 (IQR 78) respectively, 123 (IQR 155) of milled splints, (both: r = 0.31, p = .084). CONCLUSIONS: Within the limitations of a pilot trial, 3D-printed and milled splints performed similarly in terms of patient satisfaction, complication rates and wear behavior. CLINICAL SIGNIFICANCE: Thermo-flexible material was proposed for 3D printing of occlusal splints to overcome mechanical weaknesses of previously available resins. This randomized pilot study provides evidence that this material is a viable alternative to milled splints for at least three months of clinical use. Further evidence on long-term use should be obtained.

Dual-energy CT-based stopping power prediction for dental materials in particle therapy.

Radiotherapy with protons or light ions can offer accurate and precise treatment delivery. Accurate knowledge of the stopping power ratio (SPR) distribution of the tissues in the patient is crucial for improving dose prediction in patients during planning. However, materials of uncertain stoichiometric composition such as dental implant and restoration materials can substantially impair particle therapy treatment planning due to related SPR prediction uncertainties. This study investigated the impact of using dual-energy computed tomography (DECT) imaging for characterizing and compensating for commonly used dental implant and restoration materials during particle therapy treatment planning. Radiological material parameters of ten common dental materials were determined using two different DECT techniques: sequential acquisition CT (SACT) and dual-layer spectral CT (DLCT). DECT-based direct SPR predictions of dental materials via spectral image data were compared to conventional single-energy CT (SECT)-based SPR predictions obtained via indirect CT-number-to-SPR conversion. DECT techniques were found overall to reduce uncertainty in SPR predictions in dental implant and restoration materials compared to SECT, although DECT methods showed limitations for materials containing elements of a high atomic number. To assess the influence on treatment planning, an anthropomorphic head phantom with a removable tooth containing lithium disilicate as a dental material was used. The results indicated that both DECT techniques predicted similar ranges for beams unobstructed by dental material in the head phantom. When ion beams passed through the lithium disilicate restoration, DLCT-based SPR predictions using a projection-based method showed better agreement with measured reference SPR values (range deviation: 0.2 mm) compared to SECT-based predictions. DECT-based SPR prediction may improve the management of certain non-tissue dental implant and restoration materials and subsequently increase dose prediction accuracy.

Head and Neck Pain Drawing Area Correlates With Higher Psychosocial Burden But Not With Joint Dysfunction in Temporomandibular Disorders: A Cross-Sectional Study.

Head and neck pain drawings have been introduced as part of the diagnostic gold standard for temporomandibular disorders (TMD). We aimed to quantify the spatial extent of pain in TMD patients and to analyze its association with further clinical findings. In a cross-sectional study, 90 patients (median age = 38 years; n women = 68) were diagnosed according to the DC/TMD. Intra-articular disorders were either confirmed or rejected by magnetic resonance imaging. The patients shaded all painful areas in a sketch of the left and right side of a face. A grid template was placed over the drawings and each region that contained markings was scored as painful. The correlation between the calculated area and the psychosocial variables (DC/TMD axis II) as well as the influence of pain lateralization were investigated using Spearman correlation, Mann-Whitney-U and chi-square tests. Pain affected all facial areas but concentrated on the regions of the temporomandibular joint and masseter origin. Thirty-nine percent reported purely unilateral pain, which was associated with structural TMJ findings in 77% of cases. Individuals with bilateral pain and those with greater spatial spread of pain had significantly higher scores on all axis II variables, except for functional limitation of the jaw. PERSPECTIVE: Head and neck pain drawings can contribute to a stratification of TMD patients. A greater extent of pain as well as pain bilateralization is associated with higher levels of emotional distress, pain chronicity and somatization, but not with functional impairment. Unilateral reporting of pain is associated with more intra-articular disorders.

Fit of anterior restorations made of 3D-printed and milled zirconia: An in-vitro study.

OBJECTIVES: To evaluate the fit of zirconia veneers made by either 3D printing or milling. METHODS: A typodont maxillary central incisor was prepared for a 0.5-mm-thick veneer and was reproduced 36 times from resin. Restorations were designed with a 20-µm-wide marginal and a 60-µm-wide internal cement gap, and were made from 3D-printed zirconia (LithaCon 3Y 210, Lithoz, n = 24) and milled zirconia (Cercon ht, DentsplySirona, n = 12). For milled zirconia, a drill compensation was needed to give the milling bur access to the intaglio surface. The restorations were cemented, cross-sectioned, and the cement gap size was analyzed by two raters. Inter-rater reliability was studied at 12 3D-printed veneers (intraclass correlation coefficient, ICC, mixed model, absolute agreement). Twelve remaining 3D-printed restorations were compared with 12 milled restorations regarding fit at three locations: marginally, labially, and at the incisal edge (Mann-Whitney U-tests, α<0.05). RESULTS: Inter-rater reliability was excellent, with an ICC single-measure coefficient of 0.944 (95%-confidence interval: [0.907; 0.966]). Gap sizes (mean ± SD / maximum) were 55 ± 9 / 143 µm at the margins, 68 ± 14 / 130 µm labially, and 78 ± 19 / 176 µm at the incisor edge for 3D-printed veneers. For milled veneers, gap sizes were 44 ± 11 / 141 µm at the margins, 85 ± 19 / 171 µm labially, and 391 ± 26 / 477 µm at the incisor edge. At the margins, the milled veneers outperformed the 3D-printed restorations (p = 0.011). The cement gap at the incisor edge was significantly smaller after 3D printing (p < 0.001). CONCLUSIONS: 3D-printed zirconia restorations showed clinically acceptable mean marginal gaps below 100 µm. Because drill compensation could be omitted with 3D printing, the fit at the sharp incisal edge was significantly tighter than with milling. CLINICAL SIGNIFICANCE: The fit of 3D-printed ceramic anterior restorations meets clinical standards. In addition, 3D printing is associated with a greater geometrical freedom than milling. With regard to fit this feature allows tighter adaptation even after minimally invasive preparation.

Reliability and accuracy of intraoral radiography, cone beam CT, and dental MRI for evaluation of peri-implant bone lesions at zirconia implants - an ex vivo feasibility study.

OBJECTIVES: To determine the reliability and accuracy of intraoral radiography (IR), cone-beam-computed tomography (CBCT), and dental magnetic resonance imaging (dMRI) in measuring peri­implant bone defects around single zirconia implants. METHODS: Twenty-four zirconia implants were inserted in bovine ribs with various peri­implant defect sizes and morphologies. True defect extent was measured without implant in CBCT. Defects were measured twice in IR, CBCT, and dMRI with the inserted implant by three experienced readers. Reliability was assessed by ICC, accuracy by the Friedman test, and post-hoc-Tukey's test. RESULTS: A comparable good to excellent intra- and inter-reader reliability was observed for all modalities (intra-/inter-rater-CC range for IR; CBCT; dMRI: 0.81-0.91/0.79;0.87-0.97/0.96;0.87-0.95/0.94). Accuracy was generally high, with mean errors below 1 mm in all directions. However, measuring defect depth in the mesiodistal direction was significantly more accurate in dMRI (0.65 ± 0.38 mm) compared to IR (2.71 ± 1.91 mm), and CBCT (1.98 ± 1.97 mm), p-values ≤ 0.0001 respectively ≤ 0.01. CONCLUSIONS: Osseous defects around zirconia implants can be reliably measured in IR/CBCT/dMRI in the mesiodistal directions. In addition, CBCT and dMRI allow assessment of the buccolingual directions. dMRI provides a comparable accuracy in all directions, except for the mesiodistal defect depth, where it outperforms IR and CBCT.

Nonsurgical treatment of class III malocclusion with temporomandibular disorder comorbidity: A clinical report.

The treatment of a 57-year-old woman with combined skeletal and pseudo-class III malocclusion who was also suffering from chronic myofascial orofacial pain is described. The challenge was to treat the patient's malocclusion while simultaneously managing the temporomandibular disorder. After a successful 3-month occlusal device therapy, which substantially reduced the patient's discomfort, a nonsurgical therapy by using complete-mouth fixed restorations was planned. The treatment was first tested by using printed interim restorations before monolithic zirconia restorations were provided. Stable occlusion and a pain-free outcome were observed at the 3-month follow-up.

Strength and reliability of zirconia fabricated by additive manufacturing technology.

OBJECTIVES: To test strength and reliability of 3D printed compared to milled zirconia. METHODS: Cylindrical specimens were fabricated from milled (group G1; e.max ZirCAD LT) and from 3D printed (group G2; LithaCon 3Y 230) 3-mol% yttria-stabilized tetragonal zirconia polycrystal (3Y-TZP). While G1 and G2 were sintered in one step, a further series (G3) of 3D printed 3Y-TZP was sintered in two steps including intermediate color infiltration. In each group, two different conditioning strategies were applied (n ≥ 20 samples/subgroup): (1) final polishing with #1200 diamond discs according to ISO 6872, and (2) final polishing with #220 diamond discs resulting in imperfectly polished surfaces. All samples were tested to fracture with a universal testing device (cross-head speed: 1 mm/min). Characteristic strengths and Weibull moduli were calculated. Effects were analyzed by means of either ANOVA (homocedastic data) or Welch ANOVA (heterocedastic data). RESULTS: For samples conditioned according to ISO 6872, mean flexural strengths were 1462 ± 105 MPa (G1), 1369 ± 280 MPa (G2), and 1197 ± 317 MPa (G3). For the imperfectly polished subgroups, strength values were 1461 ± 121 MPa (G1), 1349 ± 332 MPa (G2), and 1271 ± 272 MPa (G3). Although all groups showed high mean strength values, the reliability of milled zirconia (Weibull moduli 14 < m <16) outperformed that of the 3D-printed material (3 < m <6). SIGNIFICANCE: Even after color infiltration in a partially sintered state, the tested 3D printed zirconia exceeded the ISO flexural strength criteria for all types of fixed ceramic restorations by far (800 MPa for class 6, ISO 6872), indicating its high potential for clinical use. Further optimization of the internal material structure after sintering might improve the reliability of 3D printed zirconia which is currently inferior to that of milled zirconia.

Retentive force of conical crowns combining zirconia and fiber-reinforced composite.

PURPOSE: This study investigated the retentive force of conical crowns combining zirconia primary and fiber-reinforced composite (FRC) secondary crowns and their changes due to aging. METHODS: Zirconia primary crowns were produced with a convergence angle of 3°. Thirty-two secondary crowns were milled from FRC and divided into two groups (n = 16/group) based on the polishing method of the secondary crown inner surfaces: diamond paste (Group 1) and silicone points (Group 2). After fitting the secondary crowns with different fitting forces (F), loosening forces (L) were determined. Tests were repeated after an occlusal stop (OS) was added to the secondary crown and artificial aging (10,000 insertion/removal cycles). Data were compared using the Wilcoxon and Mann-Whitney U tests. RESULTS: Crowns without an OS showed L/F ratios of 0.4586 (Group 1) and 0.4104 (Group 2). With an OS, maximum retention was not significantly affected by the polishing method and could be limited to Lmax = 19.31±7.77 N (Group 1) and Lmax = 16.12±5.92 N (Group 2). CONCLUSIONS: These findings suggest that the combination of conical zirconia primary and FRC secondary crowns can obtain acceptable retentive forces that are not affected by aging if the inner surfaces are polished with diamond paste. OS generation could limit maximum retention, but should be adjusted if the target value of 10 N is not to be exceeded. With a change of the convergence angle to 4°, L/F values for crowns without an OS would be close to 1/3, which is considered ideal for conical crowns. CLINICAL SIGNIFICANCE: The combination of zirconia primary crowns and FRC secondary crowns was found feasible to ensure the required retention for clinical use over a long time span. Furthermore, it offers an alternative to metal-based restorations while ensuring high levels of biocompatibility and esthetics.

High-Resolution Single Tooth MRI With an Inductively Coupled Intraoral Coil-Can MRI Compete With CBCT?

OBJECTIVES: The aims of this study were to quantify T1/T2-relaxation times of the dental pulp, develop a realistic tooth model, and compare image quality between cone-beam computed tomography (CBCT) and high-resolution magnetic resonance imaging (MRI) of single teeth using a wireless inductively coupled intraoral coil. METHODS: T1/T2-relaxometry was performed at 3 T in 10 healthy volunteers (283 teeth) to determine relaxation times of healthy dental pulp and develop a realistic tooth model using extracted human teeth. Eight MRI sequences (DESS, CISS, TrueFISP, FLASH, SPACE, TSE, MSVAT-SPACE, and UTE) were optimized for clinically applicable high-resolution imaging of the dental pulp. In model, image quality of all sequences was assessed quantitatively (contrast-to-noise ratio) and qualitatively (visibility of anatomical structures and extent of susceptibility artifacts using a 5-point scoring scale). Cone-beam computed tomography served as the reference modality for qualitative assessment. Statistical analysis was performed using 2-way analysis of variance, Fisher exact test, and Cohen κ. RESULTS: In vivo, relaxometry of dental pulps revealed T1/T2 relaxation times at 3 T of 738 ± 100/171 ± 36 milliseconds. For all sequences, an isotropic resolution of (0.21 mm) 3 was achieved, with acquisition times ranging from 6:19 to 8:02 minutes. In model, the highest contrast-to-noise ratio values were observed for UTE, followed by TSE and CISS. The best image/artifact quality, however, was found for DESS (mean ± SD: 1.3 ± 0.3/2.2 ± 0.0), FLASH (1.5 ± 0.3/2.4 ± 0.1), and CISS (1.5 ± 0.4/2.5 ± 0.1), at a level comparable to CBCT (1.2 ± 0.3/2.1 ± 0.1). CONCLUSIONS: Optimized MRI protocols using an intraoral coil at 3 T can achieve an image quality comparable to reference modality CBCT within clinically applicable acquisition times. Overall, DESS revealed the best results, followed by FLASH and CISS.

Imaging furcation defects with low-dose cone beam computed tomography.

Different cone beam computed tomography (CBCT) protocols have shown promising results for imaging furcation defects. This study evaluates the suitability of low-dose (LD)-CBCT for this purpose. Fifty-nine furcation defects of nine upper and 16 lower molars in six human cadavers were measured by a high-dose (HD)-CBCT protocol, a LD-CBCT protocol, and a surgical protocol. HD-CBCT and LD-CBCT measurements were made twice by two investigators and were compared with the intrasurgical measurements, which served as the reference. Furcation defect volumes generated from HD-CBCT and LD-CBCT imaging were segmented by one rater. Cohen's kappa and intraclass correlation coefficient (ICC) values were calculated to determine intra- and interrater reliability. The level of significance was set at α = 0.05. In total, 59 furcation defects of nine upper and 16 lower human molars were assessed. Comparing CBCT furcation defect measurements with surgical measurements revealed a Cohen's kappa of 0.5975 (HD-and LD-CBCT), indicating moderate agreement. All furcation defects identified by HD-CBCT were also detected by LD-CBCT by both raters, resulting in a Cohen's kappa of 1. For interrater agreement, linear furcation defect measurements showed an ICC of 0.992 for HD-CBCT and 0.987 for LD-CBCT. The intrarater agreement was 0.994(r1)/0.992(r2) for HD-CBCT and 0.987(r1)/0.991(r2) for LD-CBCT. The intermodality agreement was 0.988(r1)/0.991(r2). Paired t-test showed no significant differences between HD-CBCT and LD-CBCT measurements. LD-CBCT is a precise and reliable method for detecting and measuring furcation defects in mandibular and maxillary molars in this experimental setting. It has the potential to improve treatment planning and treatment monitoring with a far lower radiation dose than conventional HD-CBCT.

Retentive force of telescopic crowns combining fiber-reinforced composite and zirconia.

PURPOSE: This study investigated changes in the retentive force of telescopic crowns fabricated by combining a zirconia primary crown and a fiber-reinforced composite (FRC) secondary crown. METHODS: Primary zirconia crowns were produced with a nominal convergence angle of 0°. Forty-eight secondary crowns were milled from FRC and divided into three study groups (n=16/group) based on milling parameters and post-milling adjustment. The offset parameter used for the final milling step of the inner crown surface was adjusted for a tight initial fit in Group 1 (milling offset: +10 µm, i.e., 2 × 10 µm = 20 µm lower inner diameter compared with the CAD file of the crown) and for improved initial fit (milling offset: -10 µm, i.e., an enlargement of the inner crown diameter by 2 × 20 µm = 40 µm in relation to Group 1) in Groups 2 and 3. The inner surfaces of the secondary crowns were polished with diamond paste in Groups 1 and 2, and silicon points were used for Group 3. The retentive force was measured using a universal testing device. The secondary crown was placed on the primary crown, with the final fitting force set to a load of 100 N. This test was conducted before and after aging (10,000 insertion/removal cycles) under dry and wet conditions. A generalized linear model was used to estimate the differences in the retentive force to elucidate the effects of the milling parameters and polishing methods. RESULTS: We realized an initial retentive force of approximately 10 N. In Groups 2 and 3, the difference was statistically significant between the dry and wet conditions before aging (P < 0.05). There was no significant difference between the dry and wet conditions after aging in any of the groups (P > 0.05). CONCLUSION: An adequate initial retentive force can be achieved with telescopic crowns combining zirconia and FRC.

Measuring peri-implant bone lesions using low-dose cone-beam computed tomography.

PURPOSE: High-definition cone-beam computed tomography (HD-CBCT) offers superior image quality at the cost of higher radiation dose compared to low-dose CBCT (LD-CBCT). The aim of this study was to investigate whether peri-implant bone lesions can be accurately quantified using LD-CBCT, even when including the influence of surrounding tissues. METHODS: Twelve titanium implants restored with all-ceramic crowns were placed in bovine bone, and peri-implant lesions were prepared. Radiographic imaging was performed using IR (intraoral radiography), HD-CBCT and LD-CBCT. To simulate the in-vivo situation, the samples were placed inside a dry human mandible, and a second LD-CBCT imaging was performed (LD-CBCT*). The datasets were presented to four observers in random order. Maximum lesion depth and width were measured in a standardized mesiodistal slice in IR, HD-CBCT, LD-CBCT, and LD-CBCT*. Mean lesion depth and width measurements for each sample in HD-CBCT served as reference. RESULTS: Interrater agreement was slight for depth and excellent for width in HD-CBCT and both LD modes. For all observers, measurement deviations from HD-CBCT were below 0.3 mm in the LD protocols (LD-CBCT depth: 0.22 ± 0.17 mm, width: 0.22 ± 0.13 mm; LD-CBCT* depth: 0.24 ± 0.23 mm, width: 0.25 ± 0.21 mm) and at 0.4 mm in IR. CONCLUSION: Absolute differences between LD-CBCT and HD-CBCT are small, although surrounding tissues decrease LD-CBCT image quality. Within the limitations of an in-vitro trial, LD-CBCT may become an adequate imaging modality for monitoring peri-implant lesions at a substantially decreased radiation dose.

In-vitro fit of experimental full-arch restorations made from monolithic zirconia.

PURPOSE: Fabrication inaccuracies can compromise the fit of large-span monolithic zirconia restorations. Sintering distortion is a particular problem. This study aimed to assess the fit of full-arch restorations made from monolithic zirconia for different abutment configurations. METHODS: To quantify fit inaccuracies created during the fabrication of experimental large-span restorations, an in-vitro model with eight abutment teeth was equipped with strain gauges. Ten 14-unit restorations were made from monolithic zirconia and seated on the model in turn. For each of the ten restorations, measurements were taken for three different abutment configurations-polygonal, quadrangular, and unilaterally shortened. Strains exerted during seating were recorded in the anterior-posterior and buccal-palatal directions, and the resulting horizontal forces (rhF) were calculated along with the respective abutment deflection (ad). Data were analyzed using Kruskal-Wallis tests at a significance level of 0.05. RESULTS: All restorations could be seated on the multi-abutment model. The restorations exhibited fabrication misfits, tending to be too wide. Mean rhF/ad were largest for the quadrangular configuration (16.8±2.9 N/0.065 mm) and smallest for the polygonal configuration (13.6±4.5 N/0.053 mm). The largest rhF/ad were measured on abutments of the unilaterally shortened configuration, with a maximum deflection of 0.126 mm. For two of three configurations, rhF/ad were significantly larger for the distal abutments than for the other abutments. CONCLUSION: Even if milling and sintering procedures are optimum, misfit-induced horizontal forces cannot be avoided. Because of the natural tooth mobility, however, the fit of full-arch restorations made from monolithic zirconia might be clinically acceptable.