ABSTRACT
Following work with TADDOLs and BINOLs, we have now prepared Salen derivatives (2, 3, 14, 15, 18, 19, 20, 21) carrying two to eight styryl groups for cross-linking copolymerization with styrene. The Salen cores are either derived from (R,R)-diphenyl ethylene diamine (3, 15, 19, 21) or from (R,R)-cyclohexane diamine (2, 14, 18, 20). The styryl groups are attached to the salicylic aldehyde moieties, using Suzuki (cf. 1) or Sonogashira cross-coupling (cf. 11), and/or phenolic etherification (cf. 5, 7) with dendritic styryl-substituted Fréchet-type benzylic branch bromides. Subsequent condensation with the diamines provides the chiral Salens. Corresponding Salens lacking the peripheral vinyl groups (cf. 12, 13, 16, 17) were also prepared for comparison of catalytic activities in homogeneous solution with those in polystyrene. Cross-linking radical suspension copolymerization of styrene and the styryl Salens, following a procedure by Itsuno and Fréchet, gave beads (ca. 400 microm diameter) which were loaded with Mn or Cr (ca. 0.2 mmol of complex per g of polymer), with more than 95% of the Salen incorporated being actually accessible for complexation (by elemental analysis). The polymer-bound Mn and Cr complexes were used as catalysts for epoxidations of six phenyl-substituted olefins (m-CPBA/NMO; products 22a-f), and for dihydropyranone formation from the Danishefsky diene and aldehydes (PhCHO, C5H11CHO, C6H11CHO, products 23a-c). There are several remarkable features of the novel immobilized Salens: i) The dendritic branches do not slow down the catalytic activity of the complexes in solution; ii) the reactions with Salen catalysts incorporated in polystyrene give products of essentially the same enantiopurity as those observed in homogeneous solution with the dendritically substituted or with the original Jacobsen - Katsuki complexes; iii) some Mn-loaded beads have been stored for a year, without loss of activity; iv) especially the biphenyl- and the acetylene-linked Salen polymers (p-2, -3, -20, -21, Figure 2, 3) give Mn complexes of excellent performance: after ten uses (without re-charging with Mn!) there is no loss of enantioselectivity or degree of conversion under the standard conditions.
ABSTRACT
The chiral ligand 1,1'-bi-2-naphthol (BINOL) has been succesfully immobilized on polystyrene. Several dendritic and non-dendritic BINOL derivatives (3, and 13-17), bearing at least two polymerizable styryl groups, were prepared and fully characterized. Suspension copolymerization of the MOM- or TIPS-protected cross-linking BINOL ligands (MOM = methyloxymethyl, TIPS = triisopropylsilyl) with styrene, cleavage of the protecting-groups, and loading with a Lewis-acid afforded catalytically active polystyrene-supported BINOLates. The polymer-bound BINOLs p-3, and p-13-p-16 were tested in the Ti-BINOLate-mediated addition of Et2Zn to PhCHO. The enantioselectivities (up to 93%) and conversions obtained with the polymer-bound catalysts were in most cases identical (within experimental error) to those obtained with the unsubstituted 1,1'-bi-2-naphthol and with the non-polymerized BINOL cross-linkers under homogeneous conditions. Special focus was put on the reusability of the supported catalyst: the polymer-beads were used in up to 20 consecutive catalytic runs, with the best polymers showing no or only minor loss of selectivity. BINOL-polymers p-17, obtained by copolymerization of a 3,3'-distyryl-substituted BINOL 17a with styrene, were used in the BINOL. AlMe-mediated cycloaddition of diphenyl nitrone with alkyl vinyl ethers. In all cases the exo/endo selectivity (> or =92:8) and the enantioselectivities with which the exo-cycloadducts were formed (> or =95%) correspond to those observed in the homogeneous reactions. A dendritically cross-linked BINOL-polymer was also employed in the Ti-BINOLate-mediated cyanosilylation of pivalaldehyde. The enantiopurity of the cyanohydrine obtained in the first run was as high as in the homogeneous reaction (72%); surprisingly the catalytic performance of the supported catalyst increased steadily during the first catalytic cycles to reach 83%. Thus, cross-linking BINOLs can be succesfully incorporated into a polystyrene matrix (without racemization!) to give polymer-bound BINOL ligands that give excellent performance over many catalytic cycles with catalytic activities comparable with those of soluble analogues.
