Correction: Luminescence and photoelectrochemical properties of size-selected aqueous copper-doped Ag-In-S quantum dots.

[This corrects the article DOI: 10.1039/C8RA00257F.].

Enhanced photoconductivity of hybrid 2D-QD MoS2-AgInS2 structures.

This study describes the fabrication of hybrid two-dimensional (2D)-quantum dot (QD) MoS2-AgInS2 photoconductive devices through the mechanical pressing of a MoS2 flake onto an AgInS2 QD film. The devices exhibit an enhanced photoresponse at both continuous and modulated optical excitations, compared with the bare MoS2 or AgInS2 layer, due to the formation of a built-in electric field near the MoS2/AgInS2 interface. The continuous wave photoresponse is significantly higher due to the effective photoconductive gain when electrons flow freely through the MoS2 flake, whereas holes are effectively trapped in AgInS2 QDs. The study highlights the potential of hybrid 2D-QD MoS2-AgInS2 devices for photovoltaic and optoelectronic applications.

Influence of Thermal and Flash-Lamp Annealing on the Thermoelectrical Properties of Cu2ZnSnS4 Nanocrystals Obtained by "Green" Colloidal Synthesis.

The problem with waste heat in solar panels has stimulated research on materials suitable for hybrid solar cells, which combine photovoltaic and thermoelectric properties. One such potential material is Cu2ZnSnS4 (CZTS). Here, we investigated thin films formed from CZTS nanocrystals obtained by "green" colloidal synthesis. The films were subjected to thermal annealing at temperatures up to 350 °C or flash-lamp annealing (FLA) at light-pulse power densities up to 12 J/cm2. The range of 250-300 °C was found to be optimal for obtaining conductive nanocrystalline films, for which the thermoelectric parameters could also be determined reliably. From phonon Raman spectra, we conclude that in this temperature range, a structural transition occurs in CZTS, accompanied by the formation of the minor CuxS phase. The latter is assumed to be a determinant for both the electrical and thermoelectrical properties of CZTS films obtained in this way. For the FLA-treated samples, the film conductivity achieved was too low to measure the thermoelectric parameters reliably, although the partial improvement of the CZTS crystallinity is observed in the Raman spectra. However, the absence of the CuxS phase supports the assumption of its importance with respect to the thermoelectric properties of such CZTS thin films.

The Influence of Process Parameters on the Microstructural Properties of Spray-Pyrolyzed ß-Ga2O3.

In this work, the deposition of ß-Ga2O3 microstructures and thin films was performed with Ga(NO3)3 solutions by ultrasonic nebulization and spray coating as low-cost techniques. By changing the deposition parameters, the shape of ß-Ga2O3 microstructures was controlled. Micro-spheres were obtained by ultrasonic nebulization. Micro-flakes and vortices were fabricated by spray coating aqueous concentrated and diluted precursor solutions, respectively. Roundish flakes were achieved from water-ethanol mixtures, which were rolled up into tubes by increasing the number of deposition cycles. Increasing the ethanol-to-water ratio allows continuous thin films at an optimal Ga(NO3)3 concentration of 0.15 M and a substrate temperature of 190 °C to be formed. The monoclinic ß-Ga2O3 phase was achieved by thermal annealing at 1000 °C in an ambient atmosphere. Scanning electronic microscopy (SEM), X-ray diffraction (XRD), and UV-Raman spectroscopy were employed to characterize these microstructures. In the XRD study, in addition to the phase information, the residual stress values were determined using the sin2(ψ) method. Raman spectroscopy confirms that the ß-Ga2O3 phase and relative shifts of the Raman modes of the different microstructures can partially be assigned to residual stress. The high-frequency Raman modes proved to be more sensitive to shifting and broadening than the low-frequency Raman modes.

Core and Shell Contributions to the Phonon Spectra of CdTe/CdS Quantum Dots.

The parameters of the shell and interface in semiconductor core/shell nanocrystals (NCs) are determinant for their optical properties and charge transfer but are challenging to be studied. Raman spectroscopy was shown earlier to be a suitable informative probe of the core/shell structure. Here, we report the results of a spectroscopic study of CdTe NCs synthesized by a facile route in water, using thioglycolic acid (TGA) as a stabilizer. Both core-level X-ray photoelectron (XPS) and vibrational (Raman and infrared) spectra show that using thiol during the synthesis results in the formation of a CdS shell around the CdTe core NCs. Even though the spectral positions of the optical absorption and photoluminescence bands of such NCs are determined by the CdTe core, the far-infrared absorption and resonant Raman scattering spectra are dominated by the vibrations related with the shell. The physical mechanism of the observed effect is discussed and opposed to the results reported before for thiol-free CdTe Ns as well as CdSe/CdS and CdSe/ZnS core/shell NC systems, where the core phonons were clearly detected under similar experimental conditions.

Deposition of Nanosized Amino Acid Functionalized Bismuth Oxido Clusters on Gold Surfaces.

Bismuth compounds are of growing interest with regard to potential applications in catalysis, medicine, and electronics, for which their environmentally benign nature is one of the key factors. One thing that currently hampers the further development of bismuth oxido-based materials, however, is the often low solubility of the precursors, which makes targeted immobilisation on substrates challenging. We present an approach towards the solubilisation of bismuth oxido clusters by introducing an amino carboxylate as a functional group. For this purpose, the bismuth oxido cluster [Bi38O45(NO3)20(dmso)28](NO3)4·4dmso (dmso = dimethyl sulfoxide) was reacted with the sodium salt of tert-butyloxycabonyl (Boc)-protected phenylalanine (L-Phe) to obtain the soluble and chiral nanocluster [Bi38O45(Boc-Phe-O)24(dmso)9]. The exchange of the nitrates by the amino carboxylates was proven by nuclear magnetic resonance, Fourier-transform infrared spectroscopy, as well as elemental analysis and X-ray photoemission spectroscopy. The solubility of the bismuth oxido cluster in a protic as well as an aprotic polar organic solvent and the growth mode of the clusters upon spin, dip, and drop coating on gold surfaces were studied by a variety of microscopy, as well as spectroscopic techniques. In all cases, the bismuth oxido clusters form crystalline agglomerations with size, height, and distribution on the substrate that can be controlled by the choice of the solvent and of the deposition method.

Raman Spectroscopy and Thermoelectric Characterization of Composite Thin Films of Cu2ZnSnS4 Nanocrystals Embedded in a Conductive Polymer PEDOT:PSS.

Cu2ZnSnS4 (CZTS) is an intensively studied potential solar cell absorber and a promising thermoelectric (TE) material. In the form of colloidal nanocrystals (NCs), it is very convenient to form thin films on various substrates. Here, we investigate composites of CZTS NCs with PEDOT:PSS, a widely used photovoltaics polymer. We focus on the investigation of the structural stability of both NCs and polymers in composite thin films with different NC-to-polymer ratios. We studied both pristine films and those subjected to flash lamp annealing (FLA) or laser irradiation with various power densities. Raman spectroscopy was used as the main characterization technique because the vibrational modes of CZTS NCs and the polymer can be acquired in one spectrum and thus allow the properties of both parts of the composite to be monitored simultaneously. We found that CZTS NCs and PEDOT:PSS mutually influence each other in the composite. The thermoelectric properties of PEDOT:PSS/CZTS composite films were found to be higher compared to the films consisting of bare materials, and they can be further improved by adding DMSO. However, the presence of NCs in the polymer deteriorates its structural stability when subjected to FLA or laser treatment.

Raman and X-ray Photoelectron Spectroscopic Study of Aqueous Thiol-Capped Ag-Zn-Sn-S Nanocrystals.

The synthesis of (Cu,Ag)-Zn-Sn-S (CAZTS) and Ag-Zn-Sn-S (AZTS) nanocrystals (NCs) by means of "green" chemistry in aqueous solution and their detailed characterization by Raman spectroscopy and several complementary techniques are reported. Through a systematic variation of the nominal composition and quantification of the constituent elements in CAZTS and AZTS NCs by X-ray photoemission spectroscopy (XPS), we identified the vibrational Raman and IR fingerprints of both the main AZTS phase and secondary phases of Ag-Zn-S and Ag-Sn-S compounds. The formation of the secondary phases of Ag-S and Ag-Zn-S cannot be avoided entirely for this type of synthesis. The Ag-Zn-S phase, having its bandgap in near infrared range, is the reason for the non-monotonous dependence of the absorption edge of CAZTS NCs on the Ag content, with a trend to redshift even below the bandgaps of bulk AZTS and CZTS. The work function, electron affinity, and ionization potential of the AZTS NCs are derived using photoelectron spectroscopy measurements.

Photoinduced Enhancement of Photoluminescence of Colloidal II-VI Nanocrystals in Polymer Matrices.

The environment strongly affects both the fundamental physical properties of semiconductor nanocrystals (NCs) and their functionality. Embedding NCs in polymer matrices is an efficient way to create a desirable NC environment needed for tailoring the NC properties and protecting NCs from adverse environmental factors. Luminescent NCs in optically transparent polymers have been investigated due to their perspective applications in photonics and bio-imaging. Here, we report on the manifestations of photo-induced enhancement of photoluminescence (PL) of aqueous colloidal NCs embedded in water-soluble polymers. Based on the comparison of results obtained on bare and core/shell NCs, NCs of different compounds (CdSe, CdTe, ZnO) as well as different embedding polymers, we conclude on the most probable mechanism of the photoenhancement for these sorts of systems. Contrary to photoenhancement observed earlier as a result of surface photocorrosion, we do not observe any change in peak position and width of the excitonic PL. Therefore, we suggest that the saturation of trap states by accumulated photo-excited charges plays a key role in the observed enhancement of the radiative recombination. This suggestion is supported by the unique temperature dependence of the trap PL band as well as by power-dependent PL measurement.

Mercury-indium-sulfide nanocrystals: A new member of the family of ternary in based chalcogenides.

A general synthesis approach of aqueous glutathione-capped ternary Ag-In-S, Cu-In-S, and Hg-In-S nanocrystals (NCs) is introduced, allowing the NC composition to be varied in a broad range. Ternary Hg-In-S (HIS) NCs are reported for the first time and found to have the same tetragonal chalcopyrite motif as Cu-In-S and Ag-In-S NCs, corroborated by phonon spectra, while X-ray photoelectron spectroscopic data indicate mercury to be present as Hg+ in the Hg-In-S NCs. Colloidal HIS and Hg-In-S/ZnS NCs showed little or no variations of the spectral width of the photoluminescence band upon NC size selection, temperature variation in a broad range of 10-350 K, deposition of a ZnS shell, or postsynthesis annealing. All these observations are similar to those reported earlier for Ag-In-S and Ag-In-S/ZnS NCs and allowed us to assume a general photoluminescence mechanism for all three ternary compounds, based on the model of radiative self-trapped exciton recombination.

Molecular Engineering of Conjugated Acetylenic Polymers for Efficient Cocatalyst-free Photoelectrochemical Water Reduction.

Conjugated polymers featuring tunable band gaps/positions and tailored active centers, are attractive photoelectrode materials for water splitting. However, their exploration falls far behind their inorganic counterparts. Herein, we demonstrate a molecular engineering strategy for the tailoring aromatic units of conjugated acetylenic polymers from benzene- to thiophene-based. The polarized thiophene-based monomers of conjugated acetylenic polymers can largely extend the light absorption and promote charge separation/transport. The C≡C bonds are activated for catalyzing water reduction. Using on-surface Glaser polycondensation, as-fabricated poly(2,5-diethynylthieno[3,2-b]thiophene) on commercial Cu foam exhibits a record H2 -evolution photocurrent density of 370 µA cm-2 at 0.3 V vs. reversible hydrogen electrode among current cocatalyst-free organic photocathodes (1-100 µA cm-2 ). This approach to modulate the optical, charge transfer, and catalytic properties of conjugated polymers paves a critical way toward high-activity organic photoelectrodes.

Flexible plasmonic graphene oxide/heterostructures for dual-channel detection.

Graphene oxide (GO) films are deposited on flexible Kapton substrates and selectively modified to conductive reduced graphene oxide (rGO) electrodes using laser patterning. Based on this, we design, fabricate, and test a flexible sensor integrating laser-reduced GO with silver plasmonic nanostructures. The fabricated device results in dual transduction channels: for electrochemical and plasmonic nanostructure-based surface-enhanced Raman spectroscopy (SERS) detection. The spectroscopic analysis verifying the formation of rGO and the modification by silver nanostructures is performed by Raman, energy dispersive X-ray (EDX), and X-ray photoelectron spectroscopy (XPS). The morphological investigation is followed by optical and scanning electron microscopy imaging. In addition to pristine silver nanostructures, the Raman spectroscopy results show the formation of species such as Ag2O, Ag2CO3, and Ag2SOx. A dual-channel sensor device based on electrochemical and plasmonic detection is fabricated as a demonstration of our Ag-rGO flexible concept architecture. The dual-channel device performance is successfully demonstrated in the electrochemical and SERS detection of 4-nitrobenzenethiol (4-NBT) using the same device. Our results show that without Ag nanostructures the sensitivity in the electrochemical and optical channels is not sufficient to detect 4-NBT. The performance and stability of the silver modified device are also verified. This work demonstrates an inexpensive, highly efficient, and greener way that is compatible with solution-processing technology for the production of flexible GO-based electrochemical and SERS detection devices integrated with plasmonic nanostructures.

Raman study of flash-lamp annealed aqueous Cu2ZnSnS4 nanocrystals.

The effect of flash-lamp annealing (FLA) on the re-crystallization of thin films made of colloidal Cu2ZnSnS4 nanocrystals (NCs) is investigated by Raman spectroscopy. Unlike similar previous studies of NCs synthesized at high temperatures in organic solvents, NCs in this work, which have diameters as small as 2-6 nm, were synthesized under environmentally friendly conditions in aqueous solution using small molecules as stabilizers. We establish the range of FLA conditions providing an efficient re-crystallization in the thin film of NCs, while preserving their kesterite structure and improving their crystallinity remarkably. The formation of secondary phases at higher FLA power densities, as well as the dependence of the formation on the film thickness are also investigated. Importantly, no inert atmosphere for the FLA treatment of the NCs is required, which makes this technology even more suitable for mass production, in particular for printed thin films on flexible substrates.

"Green" Aqueous Synthesis and Advanced Spectral Characterization of Size-Selected Cu2ZnSnS4 Nanocrystal Inks.

Structure, composition, and optical properties of colloidal mercaptoacetate-stabilized Cu2ZnSnS4 (CZTS) nanocrystal inks produced by a "green" method directly in aqueous solutions were characterized. A size-selective precipitation procedure using 2-propanol as a non-solvent allows separating a series of fractions of CZTS nanocrystals with an average size (bandgap) varying from 3 nm (1.72 eV) to 2 nm (2.04 eV). The size-selected CZTS nanocrystals revealed also phonon confinement, with the main phonon mode frequency varying by about 4 cm-1 between 2 nm and 3 nm NCs.

Luminescence and photoelectrochemical properties of size-selected aqueous copper-doped Ag-In-S quantum dots.

Ternary luminescent copper and silver indium sulfide quantum dots (QDs) can be an attractive alternative to cadmium and lead chalcogenide QDs. The optical properties of Cu-In-S and Ag-In-S (AIS) QDs vary over a broad range depending on the QD composition and size. The implementation of ternary QDs as emitters in bio-sensing applications can be boosted by the development of mild and reproducible syntheses directly in aqueous solutions as well as the methods of shifting the photoluminescence (PL) bands of such QDs as far as possible into the near IR spectral range. In the present work, the copper-doping of aqueous non-stoichiometric AIS QDs was found to result in a red shift of the PL band maximum from around 630 nm to ∼780 nm and PL quenching. The deposition of a ZnS shell results in PL intensity recovery with the highest quantum yield of 15%, with almost not change in the PL band position, opposite to the undoped AIS QDs. Size-selective precipitation using 2-propanol as a non-solvent allows discrimination of up to 9 fractions of Cu-doped AIS/ZnS QDs with the average sizes in the fractions varying from around 3 to 2 nm and smaller and with reasonably the same composition irrespective of the QD size. The decrease of the average QD size results in a blue PL shift yielding a series of bright luminophors with the emission color varies from deep-red to bluish-green and the PL efficiency increases from 11% for the first fraction to up to 58% for the smallest Cu-doped AIS/ZnS QDs. The rate constant of the radiative recombination of the size-selected Cu-doped AIS/ZnS QDs revealed a steady growth with the QD size decrease as a result of the size-dependent enhancement of the spatial exciton confinement. The copper doping was found to result in an enhancement of the photoelectrochemical activity of CAIS/ZnS QDs introduced as spectral sensitizers of mesoporous titania photoanodes of liquid-junction solar cells.