Advancement of electro-optical properties through changes in the physicochemical composition of hybrid thin films by doping reduced graphene oxide into a sol-gel process solution.

A hybrid thin film was fabricated by doping graphene oxide into a sol-gel solution containing a mixture of zirconium, bismuth, and indium oxide. The thin film was fabricated using a brush coating process. The graphene oxide doping ratios used were 0, 5, and 15 wt%. During the thin film fabrication process, the produced sol-gel solution generates a contractile force due to the shear stress of the brush bristles, resulting in a microgroove structure. This structure was confirmed through scanning electron microscopy analysis, which revealed the clear presence of rGO. Comparing the electrical properties of a zirconium bismuth indium oxide thin film without graphene oxide doping and a thin film doped with 15 wt% graphene oxide, the electro-optical properties were significantly improved with graphene oxide doping. In general, the threshold voltage decreased by approximately 0.42 V. In addition, bandgap measurements confirmed the improved conductivity characteristics with graphene oxide doping. Since this improvement in electro-optical properties is associated with the reduction process due to graphene oxide doping, X-ray photoelectron spectroscopy analysis was performed to assess the intensity change of each element. Based on these observations, hybrid thin films doped with graphene oxide emerge as promising candidates for next generation thin film.

Enhanced Electrical and Optical Properties of Bismuth Tantalum Oxide Thin Films through Graphene Oxide Doping.

In this study, a hybrid thin film was fabricated by doping graphene oxide in a bismuth tantalum oxide solution in the sol-gel state. The thin film was produced by a brush-coating process. The graphene oxide doping ratios used were 0, 5, and 15 wt %. In the process of producing the thin film, the prepared sol-gel solution generates contraction forces, owing to the shear stress from the bristles of the brush, forming a microgroove structure. This structure was confirmed through atomic force microscopy, transmission electron microscopy, and energy-dispersive spectroscopy analyses. As a result of line profile analysis in atomic force microscopy, the groove heights of the thin film surface at 0, 5, and 15 wt % doping were 110, 130, and 160 nm, respectively, and the width of all grooves was 1 µm. The width of all thin films was approximately 1 µm, and microgrooves were confirmed. Moreover, the hybrid thin-film formation was confirmed by X-ray photoelectron spectroscopy. By comparing the electrical properties of the bismuth tantalum oxide thin film without graphene oxide doping and the thin film doped with 15 wt % graphene oxide, it was demonstrated that the electro-optical properties increased excellently with graphene oxide doping. Typically, the threshold voltage was reduced by approximately 0.26 V. Based on these observations, graphene oxide doped bismuth tantalum oxide hybrid thin films can be considered as promising candidates for thin-film applications in next-generation displays.

Advanced thin films of indium-tin oxide doping with photosensitive polymer via embossing process.

We propose a sol-gel thin film formation process involving nanoimprint lithography. First, indium tin oxide was dissolved in 2-methoxyethanol at a ratio of 5:5 and the mixture were mixed with 10 wt% of a UV-curable. Subsequently, a polydimethylsiloxane sheet prepared by covering a silicon wafer with a polydimethylsiloxane mold was attached to a InSnO thin film to duplicate the nanostructure through UV irradiation exposure. The replicated nanostructured thin films formed about morphological and chemical composition changes on the surface, we progressed to x-ray photoelectron spectroscopy and atomic force microscopy analysis. Furthermore, atomic force microscopy image analysis showed superior patterned grooves for a UV exposure time of 3 min. A suitability test involving the measurement of the transmittance was performed for examining the suitability of the thin film for use in display devices.

High electrical characteristics through graphene oxide doping process on physicochemically reformed inorganic thin films.

This study investigated the improvement of the electro-optical properties of a liquid crystal (LC) cell fabricated through brush coating using graphene oxide (GO) doping. The physical deformation of the surface was analyzed using atomic force microscopy. The size of the groove increased as the GO dopant concentration increased, but the direction of the groove along the brush direction was maintained. X-ray photoelectron spectroscopy analysis confirmed that the number of C-C and O-Sn bonds increased as the GO concentration increased. Since the van der Waals force on the surface increases as the number of O-metal bonds increases, we were able to determine why the anchoring energy of the LC alignment layer increased. This was confirmed by residual DC voltage and anchoring energy measurements that were later performed. As the GO concentration increased, the width of the hysteresis curve decreased, indicating that the residual DC voltage decreased. Additionally, the 15% GO-doped sample exhibited a significant increase in its anchoring energy up to 1.34 × 10-3 J/m2, which is similar to that of rubbed polyimide. It also secured a high level of electro-optical properties and demonstrated potential as a next-generation thin-film display despite being produced via a simple brush-coating process.

Physicochemically modified high-resolution tin oxide thin film using soft imprinting.

We carried out nanoimprinting lithography on solution-processed tin oxide (SnO) film for use as a liquid crystal (LC) alignment layer, for which we used a parallel configuration. To transfer the nanostructures onto the SnO film, we conducted an experiment according to curing, from which fine nanostructures on the SnO film were obtained at a curing temperature of 200 °C. These acted as a guide for the arrangement of the LC molecules and induced geometric restriction which minimized elastic distortion energies, and so the LC molecules could be aligned in the direction of the nanostructures. The LC alignment state was investigated using polarized optical microscopy, and the pre-tilt angle was measured using a crystal rotation method. With high thermal endurance and drastically low power consumption, the nano patterned SnO was shown to be a promising candidate for LC applications. The nanopatterning process combined with nanoimprinting lithography and solution-processed inorganic materials exhibited the possibility of broadening the features of nanostructure-mounted applications, including LC devices.

Self-Aligned Liquid Crystals on Anisotropic Nano/Microstructured Lanthanum Yttrium Strontium Oxide Layer.

We propose an efficient alignment method for liquid crystals (LCs). A brush-coating method handles film deposition and LC alignment treatment simultaneously herein, meaning a reduction in the conventional alignment layer treatment process steps. A lanthanum yttrium strontium oxide (LaYSrO) film prepared by the sol-gel process was used for the alignment layer. Topographical details of the brush-coated LaYSrO films (compared with spin-coated films) were investigated by atomic force microscopy. Spin-coated LaYSrO meant that the film formation alone without orientation treatment represented an isotropic surface. On the other hand, the 270 °C-cured brush-coated LaYSrO showed nano/microstructure with directionality. It indicates that brush-hair sweeping induced shearing stress on the sol state of the LaYSrO, which results in surface anisotropy for LC alignment. The uniform LC alignment state was confirmed by polarized optical microscopy and pretilt analysis. The brush-coated LaYSrO shows fine optical transparency compared to plain and indium-tin-oxide coated glasses, and thermal stability up to 150 °C for LC alignment. Competitive electro-optical performances of the brush-coated LaYSrO were verified in a twisted-nematic LC system compared to those of the conventionally used polyimide layer. Consequently, we expect that the brush-coating process can be an innovative technology for LC alignment.

Physicochemically Constructed Unidirectional Aluminum Bismuth Gallium Zinc Oxide Film for Enhanced Nematic Liquid Crystal System Using a Brush-Coating Method.

We propose a convenient brush coating method for liquid crystal (LC) alignment. This method enables film deposition and an alignment layer treatment process simultaneously. Aluminum bismuth gallium zinc oxide (AlBiGaZnO) is used as the alignment layer. After the curing process, a unidirectional AlBiGaZnO film is formed; its surface morphology and chemical composition were verified using scanning electron microscopy and X-ray photoelectron spectroscopy. This oriented structure of the surface was produced by shear-stress which originated from brush movement. That structure induced a surface anisotropic characteristic and resulted in a uniform LC alignment. The uniform and homogeneous LC alignment state on the film was confirmed using polarized optical microscopy and pre-tilt angle analysis. The brush coated AlBiGaZnO film exhibited excellent thermal budget for advanced LC system. The film exhibited enhanced electro-optical performance with a low operating voltage. These results demonstrate the potential of LC alignment technology via the brush coating method.

Solution-Driven Imprinting Lithography of Sol-Gel ZnO Thin Films for Liquid Crystal Display.

We present a simple and economically convenient method to fabricate nanopatterned ZnO films by imprinting lithography and use them for the layer alignment of liquid crystal (LC) displays. First, a one-dimensional nanopattern was obtained by laser interference lithography on a silicon wafer, and the silicon mold replica was transferred onto a flexible polydimethylsiloxane (PDMS) sheet for conformal patterning. The so-obtained PDMS mold was then applied on a ZnO film spin-coated on a glass substrate. During the imprinting process, the temperature was controlled from 100 to 250 °C to observe the transferring morphologies of the ZnO film; the nanopattern was successfully transferred at annealing temperatures of 200 and 250 °C because the ZnO film at the sol state filled the cavities of the PDMS nanopattern and solidified, forming a negative replica of the nanopattern. The direction of the nanopatterned ZnO film served as a guide for aligning the LC molecules on the LC surface at the centimeter scale and, due to their elastic characteristics and group behavior, propagating their directional states in the LC bulk. The resulting LC cell exhibited an enhanced electro-optical performance and high thermal endurance above 180 °C. The geometry of the alignment layer increased the electric field on the ZnO film and showed reduced threshold voltage. In addition, since flexible devices are generally based on polyimide, which imidized at around 200 °C, the relatively low annealing temperatures of our fabricated nanopatterned ZnO film allow it to be mounted on such devices without any deterioration of the underlying thermoplastic substrate. Therefore, nanopatterned ZnO has a considerable potential for advanced LC displays.

Superior nanopatterns via adjustable nanoimprint lithography on aluminum oxide in high-K thin films with ultraviolet curable polymer.

The present study substantiate that ultraviolet-nanoimprint lithography (UV-NIL) can be used to transfer a one-dimensional nano-pattern onto a high-k thin film of aluminum oxide mixed with a UV photocuring agent. Polydimethylsiloxane (PDMS) molds fabricated on silicon wafers were made using deep ultraviolet laser interference lithography in order to investigate one-dimension nanopatterns. These imprinted nano-patterns induce geometric deformations in the liquid crystal (LC), creating collective and elastic properties, which act as a guide for homogeneous alignment. The nanoimprint method can process a large area, so it can be processed much easier, faster, and more accurately than the conventional rubbing method. Moreover, the optical properties of the nano-imprinted aluminum oxide (AlO) thin-film are about 1.5p% superior to that of conventional commercialized cells, so it has a high effect on the luminance and color gamut of the display. After pattern imprinting, atomic force microscope (AFM) was performed to confirm the result. We can compared the cycle of AlO mixed with UV photocuring agent PDMS pattern cycle, the period is 776 and 750 nm, the width is 468 and 450 nm, the spacing is 292 and 300 nm, and the height is 40 and 30 nm. The nano-imprinted film appears to replicate the width, amplitude, and spacing of the PDMS template. In addition, X-ray photoelectron spectroscopy was performed to determine the chemical properties of the thin film and it was confirmed that UV irradiation induces oxidation, thus increases the intensity significantly. The binding energies of Al 2p and C-O spectra were situated at 74.27 ± 0.5 eV and 531.78 ± 0.5 eV, respectively.

Formation of Wrinkle Structures on Styrene-b-isoprene-b-styrene Films Using One-Step Ion-Beam Irradiation.

We investigated the wrinkle formation on ion-beam (IB)-irradiated substrates coated with the thermoplastic elastomer styrene-b-isoprene-b-styrene (SIS) and demonstrate a relation of the wrinkle structure and the newly formed top layer induced by IB. IB irradiation led to polymer cross-linking on the surface, thereby forming a new skin layer, a finding which was supported by an X-ray photoelectron spectroscopy analysis, Young moduli calculated using force-distance curves, and time-of-flight secondary ion mass spectrometry depth profiling. The wrinkle wavelength increased according to the irradiation time, which indicates that the latter mainly increased the thickness of the cross-linking layer. The increase in the wrinkle wavelength varied from 420 to 670 nm by changing the IB irradiation time. In this paper, we present not only the expectation of wrinkle fabrication using our method but also the possibility of choosing diverse materials such as the thermoplastic elastomer SIS for fabrication of wrinkle structures.

One-dimensional surface wrinkling for twisted nematic liquid crystal display based on ultraviolet nanoimprint lithography.

Surface wrinkling method is used to fabricate a 1-dimensional nanostructure. The structure is transferred to an ultraviolet cured polymer which is used as an alignment layer. The anisotropic geometry serves as a guide for aligning liquid crystal molecules uniformly without defects. The TN-LC cell showed a successful LC switching, with a response time of 20.5 ms, and a threshold voltage of 2.00 V. It also exhibited high thermal stability above 180°C. The proposed UV-cured polymers with 1-D nano wrinkle geometry can be a candidate for alternative alignment techniques, for advanced liquid crystal devices with high thermal budgets.

Physicochemical Modification Effect on Homogeneously Aligned Liquid Crystals Based on the Nickel Oxide Thin Film.

We demonstrated homogeneous liquid crystal (LC) alignment on Nickel Oxide (NiO) films subjected to ion beam (IB) irradiation. Uniform LC alignment was achieved at high IB intensity values of 1200 and 1800 eV. To determine the mechanism of LC alignment following IB irradiation, physicochemical analysis was performed using atomic force microscopy and X-ray photoelectron spectroscopy. IB irradiation with high intensity increases uniformity of the surface, and IB irradiation induces the formation of oxygen vacancies and increases the NiO (Ni2+) phase components. Hence, both of the smooth surface and the strong van der Waals interactions between the NiO film and the LC molecules provides the LC molecules with a stable anchor on the surface, leading to uniform LC alignment on NiO films after IB irradiation. IB-irradiated NiO exhibited a high transparency of 85% in the visible light range as compared with the 83% average transmittance of conventional polyimide, which makes the IB-irradiated NiO alignment layer attractive in display devices.

Liquid Crystal Alignment on Solution Derived Zinc Oxide Films via Ion Beam Irradiation.

A 75-nm-thick ZnO film was deposited by a sol-gel method on indium-tin oxide (ITO)-coated glass. This film served as a liquid crystal (LC) alignment layer. We report the fabrication and characteristics of this film after ion-beam (IB) irradiation. Uniform LC alignment was achieved at an IB incident energy above 2400 eV. The IB-treated ZnO surface was analyzed by X-ray photoelectron spectroscopy (XPS), monitoring the intensity of the Zn 2p and O 1s peaks as a function of IB-irradiation energy density. The electro-optical (EO) characteristics of a twisted nematic-liquid crystal display (TN-LCD) were comparable to rubbed polyimide.

Ion beam fabrication of aluminum-doped zinc oxide layer for high-performance liquid crystals alignment.

In this paper, a 1.8 keV ion beam (IB) sputtered thin layer of aluminum-doped zinc oxide (AZO) with columnar AZO bumps covering the surface working as an alignment layer for the homogeneous alignment of liquid crystals (LC) is investigated. Bumpy AZO alignment layers in twisted nematic (TN) cells generated larger LC pre-tilt angles and thus enabled accelerated switching of LC, and the highly conductive bumpy AZO thin layers allowed super-fast release of accumulated charges, and led to low residual DC performance. These results indicate the promising applications of AZO bumps layer as alignment layer in LC devices.

Tailoring the Orientation and Periodicity of Wrinkles Using Ion-Beam Bombardment.

The present study demonstrates that surface reformation in polydimethylsiloxane can be controlled using ion-beam (IB) irradiation. This can be done by simply varying the IB incidence angle and requires no change in the energy source. By controlling the incidence angle of IB irradiation, we were able to continuously control the pattern of the wrinkle structure, that is, a randomly formed pattern or an anisotropic one. Moreover, the directional characteristics of the wrinkle pattern control the alignment of liquid crystal molecules. This control is a function of the incidence angle of the IB. These simple methods can provide considerable flexibility in the fabrication of wrinkle structures.

Localized Ion-Beam Irradiation-Induced Wrinkle Patterns.

We observe a localized irradiation-induced wrinkle pattern on poly(dimethylsiloxane) (PDMS) via a long pattern mask. Localized ion-beam irradiation induces an inhomogeneous wrinkle pattern on the treated region. To confirm the inhomogeneity of the entire wrinkle pattern, its morphology was investigated using optical microscopy, which revealed separated regions in the wrinkle pattern. We used atomic force microscopy for quantitative analysis of the wrinkle pattern morphology and analyzed the angular distribution and the direction of compressive stress of the irradiated area. We confirmed the direction of stress release along the distance from the edges, and we achieved control of the orientation of the wrinkle pattern by altering the width of the irradiated area. Investigation of the inhomogeneities in a localized wrinkle formation provides an understanding of the formation mechanism to enhance its performance and application in various fields.

Homogeneous liquid crystal alignment characteristics on solution-derived HfYGaO films treated with IB irradiation.

Solution-derived HfYGaO films have been treated by ion beam (IB) irradiation and used as liquid crystal (LC) alignment layers. Solution processing was adopted due to its simplicity, high throughput, and facile composition modification. Homogeneous and uniform LC alignment was achieved on the IB-irradiated HfYGaO films, and when these films were adopted in twisted nematic (TN) cells, electro-optical performance comparable to that of TN cells with conventional polyimide layers was achieved, with almost no capacitance-voltage hysteresis. Moreover, LC cells based on IB-irradiated HfYGaO films had a high thermal budget. The proposed IB-irradiated solution-derived HfYGaO films have considerable potential for use in advanced LC applications.

Control of the wrinkle structure on surface-reformed poly(dimethylsiloxane) via ion-beam bombardment.

We investigated the surface reformation of poly(dimethylsiloxane) (PDMS) elastomers by means of ion beam bombardment for fabricating wrinkle structures. Oxidation on the PDMS surface formed a silica-like outer layer that interacted with the inner PDMS layer, leading to the formation of wrinkle structures that minimized the combined bending energy of the outer layer and stretching energy of the inner layer. In addition, we controlled the amplitude and period of the wrinkle structures by adjusting the PDMS annealing temperature. As the PDMS annealing temperature was increased, the amplitude and period of the wrinkles formed by IB irradiation changed from 604.35 to 69.01 nm and from 3.07 to 0.80 µm, respectively.

Homogeneous self-aligned liquid crystals on wrinkled-wall poly(dimethylsiloxane) via localised ion-beam irradiation.

We demonstrate self-aligned liquid crystals (LCs) using a wrinkled-wall polydimethylsiloxane (PDMS) wrinkle structure, which is a key factor to obtain a stable homogeneous alignment state with positive LCs. We constructed the wrinkled walls via localised surface exposure to IB radiation, which passed through a long length localised pattern mask. The creation of the wrinkled wall helped to align the LC molecules homogeneously because the wrinkled wall acted as a guide for the arrangement of positive LC molecules. In addition, we confirmed the stability of the alignment state as the width of the wrinkled wall was changed. Although this wrinkled-wall method is a non-contact method, LC alignment is achieved via an anisotropic topographical guide, which provides the LC molecules with stable homogeneous alignment.

Nickel Oxide Nanoparticles Doped Liquid Crystal System for Superior Electro-Optical Properties.

We examined the properties of nematic liquid crystal (N-LC) systems with dispersed nickel oxide nanoparticles (NPs). Uniform LC alignments with regular pretilt angles were achieved on rubbed polymer surface regardless of NiO nanoparticles concentration. We confirmed the electro-optical characteristics of twisted nematic (TN) cells containing NiO nanoparticles on rubbed polymer surface, which exhibited lower threshold voltages and faster response times with less capacitance hysteresis than pure LC cells. It is clear that the response time of TN cells on rubbed polymer surfaces decreases with increasing the NiO nanoparticles concentration. These results demonstrate the relationship between NP doping concentration and trapping of impurity ions, and were confirmed by a software simulation of electric flux and field density. NiO nanoparticles in the LC cells focused the electric field flux and strengthened the electric field. Further, NiO nanoparticles in LC medium trapped charged ionic impurities and suppressed the screen effect, leading to a stronger electric field and the van der Waals interactions between LC molecules and the alignment layers.