Roughness-Controlled Cu2ZnSn(S,Se)4 Thin-Film Solar Cells with Reduced Charge Recombination.

Copper zinc tin sulfo-selenide (CZTSSe) is a promising light-absorbing material of thin-film solar cells because of its low material cost especially when it is prepared by cost-effective processes like the electrochemical deposition process. The CZTSSe thin-film solar cells, however, suffer from the relatively low efficiency, mostly because of the significant charge recombination. Given that the surface recombination is one of the major recombination paths, controlling the surface roughness, and thus the interfacial area is one of the key factors for improving their device performances. In this study, we demonstrated a simple but effective strategy for reducing the surface roughness during the electrochemical deposition process of the CZTSSe thin films. By adopting an initial nucleation stage with higher deposition currents ahead of the steady-state galvanostatic deposition, the surface of the copper-zinc-tin (CZT) precursor and CZTSSe thin films became significantly smoother and uniform (ΔRrms: -43.8% for CZT, -28.9% for CZTSSe). The effects of the surface roughness on the photovoltaic properties of the CZTSSe thin-film solar cells have been investigated systematically with various characterization techniques like the diode analysis, lifetime measurement, and the temperature dependency of the open-circuit voltage. The device with the smoother surface exhibited higher open-circuit voltage and fill factor, mostly because of the significantly reduced charge recombination, leading to the high conversion efficiency of 8.64% (active).

Al-/Ga-Doped ZnO Window Layers for Highly Efficient Cu2ZnSn(S,Se)4 Thin Film Solar Cells.

The successful use of Al-/Ga-doped ZnO (AGZO) thin films as a transparent conducting oxide (TCO) layer of a Cu2ZnSn(S,Se)4 (CZTSSe) thin film solar cell is demonstrated. The AGZO thin films were prepared by radio frequency (RF) sputtering. The structural, crystallographic, electrical, and optical properties of the AGZO thin films were systematically investigated. The photovoltaic properties of CZTSSe thin film solar cells incorporating the AGZO-based TCO layer were also reported. It has been found that the RF power and substrate temperature of the AGZO thin film are important factors determining the electrical, optical, and structural properties. The optimization process involving the RF power and the substrate temperature leads to good electrical and optical transmittance of the AGZO thin films. Finally, the CZTSSe solar cell with the AGZO TCO layer demonstrated a high conversion efficiency of 9.68%, which is higher than that of the conventional AZO counterpart by 12%.

Highly Efficient and Uniform 1†cm2 Perovskite Solar Cells with an Electrochemically Deposited NiOx Hole-Extraction Layer.

Given that the highest certified conversion efficiency of the organic-inorganic perovskite solar cell (PSC) already exceeds 22 %, which is even higher than that of the polycrystalline silicon solar cell, the significance of new scalable processes that can be utilized for preparing large-area devices and their commercialization is rapidly increasing. From this perspective, the electrodeposition method is one of the most suitable processes for preparing large-area devices because it is an already commercialized process with proven controllability and scalability. Here, a highly uniform NiOx layer prepared by electrochemical deposition is reported as an efficient hole-extraction layer of a p-i-n-type planar PSC with a large active area of >1 cm2 . It is demonstrated that the increased surface roughness of the NiOx layer, achieved by controlling the deposition current density, facilitates the hole extraction at the interface between perovskite and NiOx , and thus increases the fill factor and the conversion efficiency. The electrochemically deposited NiOx layer also exhibits extremely uniform thickness and morphology, leading to highly efficient and uniform large-area PSCs. As a result, the p-i-n-type planar PSC with an area of 1.084 cm2 exhibits a stable conversion efficiency of 17.0 % (19.2 % for 0.1 cm2 ) without showing hysteresis effects.

Compositional and Interfacial Modification of Cu2 ZnSn(S,Se)4 Thin-Film Solar Cells Prepared by Electrochemical Deposition.

A highly efficient Cu2 ZnSn(S,Se)4 (CZTSSe)-based thin-film solar cell (9.9%) was prepared using an electrochemical deposition method followed by thermal annealing. The Cu-Zn-Sn alloy films was grown on a Mo-coated glass substrate using a one-pot electrochemical deposition process, and the metallic precursor films was annealed under a mixed atmosphere of S and Se to form CZTSSe thin films with bandgap energies ranging from 1.0 to 1.2 eV. The compositional modification of the S/(S+Se) ratio shows a trade-off effect between the photocurrent and photovoltage, resulting in an optimum bandgap of roughly 1.14 eV. In addition, the increased S content near the p-n junction reduces the dark current and interface recombination, resulting in a further enhancement of the open-circuit voltage. As a result of the compositional and interfacial modification, the best CZTSSe-based thin-film solar cell exhibits a conversion efficiency of 9.9%, which is among the highest efficiencies reported so far for electrochemically deposited CZTSSe-based thin-film solar cells.

Hierarchical assembly of TiO2-SrTiO3 heterostructures on conductive SnO2 backbone nanobelts for enhanced photoelectrochemical and photocatalytic performance.

Heterostructures can play a role in enhanced photoinduced electrochemical and catalytic reactions due to the advantageous combination of two compounds. Herein, we demonstrate the fabrication of Sb:SnO2@TiO2-SrTiO3 3D heterostructures via a simple hydrothermal method using a conductive Sb:SnO2@TiO2 nanobelt electrode as a template. XRD, FESEM, and TEM analyses confirm that a well-dispersed and crystalized SrTiO3 layer is formed on the surface of TiO2 nanorods. The photoelectrochemical (PEC) performance of the heterostructure is optimized by controlling the reaction time. Details about the effect of the hydrothermal reaction time on the PEC performance are discussed. The optimized Sb:SnO2@TiO2-SrTiO3 heterostructure exhibited a higher onset potential and a saturated photocurrent in comparison to the Sb:SnO2@TiO2 nanostructure. The result is attributed to a Fermi level shift and a blocking layer effect caused by the SrTiO3. Furthermore, the photocatalytic degradation of methylene blue was significantly enhanced on the optimized Sb:SnO2@TiO2-SrTiO3. This work demonstrates that a synergetic effect between three-dimensional nanoarchitecturing and a heterojunction structure is responsible for enhanced PEC as well as improved photocatalytic performance levels, both of which can be extended to other metal-oxide and/or ternary compounds.

Highly efficient copper-zinc-tin-selenide (CZTSe) solar cells by electrodeposition.

Highly efficient copper-zinc-tin-selenide (Cu2ZnSnSe4 ; CZTSe) thin-film solar cells are prepared via the electrodepostion technique. A metallic alloy precursor (CZT) film with a Cu-poor, Zn-rich composition is directly deposited from a single aqueous bath under a constant current, and the precursor film is converted to CZTSe by annealing under a Se atmosphere at temperatures ranging from 400 °C to 600 °C. The crystallization of CZTSe starts at 400 °C and is completed at 500 °C, while crystal growth continues at higher temperatures. Owing to compromises between enhanced crystallinity and poor physical properties, CZTSe thin films annealed at 550 °C exhibit the best and most-stable device performances, reaching up to 8.0 % active efficiency; among the highest efficiencies for CZTSe thin-film solar cells prepared by electrodeposition. Further analysis of the electronic properties and a comparison with another state-of-the-art device prepared from a hydrazine-based solution, suggests that the conversion efficiency can be further improved by optimizing parameters such as film thickness, antireflection coating, MoSe2 formation, and p-n junction properties.

Enhanced performance of NaTaO3 using molecular co-catalyst [Mo3S4]4+ for water splitting into H2 and O2.

Photocatalytic activity of NaTaO(3) was significantly improved by using a molecular co-catalyst [Mo(3)S(4)](4+). Its hydrogen production rate is 28 times higher than pure NaTaO(3). This study presents the potential of bioinspired molecular metal clusters as efficient co-catalysts.