Your browser doesn't support javascript.
loading
Show: 20 | 50 | 100
Results 1 - 11 de 11
Filter
Add more filters










Publication year range
1.
ACS Appl Mater Interfaces ; 12(15): 17443-17451, 2020 Apr 15.
Article in English | MEDLINE | ID: mdl-32195558

ABSTRACT

Piezocatalysts have attracted much attention due to their excellent degradation ability for organics. In this work, three types of BaTiO3 (BTO) nanostructures, including hydrothermally synthesized nanocubes (NCs), sol-gel calcined nanoparticles (NPs), and electrospun nanofibers (NFs), are prepared for catalyzing the dye degradation. Compared with the NCs and NPs, the NFs exhibit a higher piezocatalytic degradation performance due to the large specific surface area, fine crystal size, and easy deformation structure. Moreover, the kinetic factors, including initial dye concentration, ionic strength, ultrasonic power, and applied action, influencing the degradation performance of the BTO NFs are analyzed deeply. A high degradation rate constant of 0.0736 min-1 is achieved for rhodamine B, which is superior compared with the previous reports. The excellent stability of BTO NFs is demonstrated by the cycling tests, where a high degradation efficiency of 97.6% within 110 min is still obtained after the third cycle. Furthermore, the mechanism of piezocatalysis revealed that the hydroxyl and superoxide radicals are the main reactive species in the degradation process. This work is of importance for the development of high-performance piezocatalysts and highlights the potential of piezocatalysis for water remediation.

2.
Chem Soc Rev ; 49(1): 263-285, 2020 Jan 02.
Article in English | MEDLINE | ID: mdl-31825417

ABSTRACT

Since graphene has been successfully exfoliated, two-dimensional (2D) materials constitute a vibrant research field and open vast perspectives in high-performance applications. Among them, bismuthene and 2D bismuth (Bi) are unique with superior properties to fabricate state-of-the-art energy saving, storage and conversion devices. The largest experimentally determined bulk gap, even larger than those of stanene and antimonene, allows 2D Bi to be the most promising candidate to construct room-temperature topological insulators. Moreover, 2D Bi exhibits cyclability for high-performance sodium-ion batteries, and the enlarged surface together with the good electrochemical activity renders it an efficient electrocatalyst for energy conversion. Also, the air-stability of 2D Bi is better than that of silicene, germanene, phosphorene and arsenene, which could enable more practical applications. This review aims to thoroughly explore the fundamentals of 2D Bi and its improved fabrication methods, in order to further bridge gaps between theoretical predictions and experimental achievements in its energy-related applications. We begin with an introduction of the status of 2D Bi in the 2D-material family, which is followed by descriptions of its intrinsic properties along with various fabrication methods. The vast implications of 2D Bi for high-performance devices can be envisioned to add a new pillar in energy sciences. In addition, in the context of recent pioneering studies on moiré superlattices of other 2D materials, we hope that the improved manipulation techniques of bismuthene, along with its unique properties, might even enable 2D Bi to play an important role in future energy-related twistronics.

3.
ACS Appl Mater Interfaces ; 12(1): 1061-1068, 2020 Jan 08.
Article in English | MEDLINE | ID: mdl-31820620

ABSTRACT

Emulating the essential synaptic behaviors using single synaptic transistor has attracted extensive attention for building the brain-inspired neuromorphic systems. However, few reports on synaptic transistors fabricated by solution processes have been reported. In this article, the indium oxide synaptic transistors based on polyimide substrates were fabricated by a nontoxic water-inducement method at a low temperature, and lithium perchlorate (LiClO4) was dissolved in polyethylene oxide as the gate electrolyte. For water-inducement process, comparable electrical properties of the synaptic transistors can be achieved by prolonging the annealing time rather than high-temperature annealing with a relatively short time. The effect of the annealing time on the electrical performance of the electrolyte-gated transistors annealed at various temperatures was investigated. It is found that the electrolyte-gated-synaptic transistor on polyimide substrate annealed at 200 °C exhibits high electrical performance and good mechanical stability. Due to the ion migration relaxation dynamics in the polymer electrolyte, various important synaptic behaviors such as the excitatory postsynaptic current, paired-pulse facilitation, high-pass filtering characteristics, and long-term memory performance were successfully mimicked. The electrolyte-gated synaptic transistors based on solution-processed In2O3 exhibit great potential in neuromorphological applications.


Subject(s)
Brain/metabolism , Electrolytes/chemistry , Indium/chemistry , Transistors, Electronic , Lithium Compounds/chemistry , Perchlorates/chemistry , Temperature
4.
Nanoscale ; 10(41): 19427-19434, 2018 Nov 07.
Article in English | MEDLINE | ID: mdl-30310899

ABSTRACT

Recently, metal oxide nanofibers fabricated by electrospinning have been considered as promising components for next-generation electronic devices. Unfortunately, the nanofiber-based electronic devices usually exhibited inferior electrical performance, due to the high contact resistance between the nanofibers and the inferior interfacial adhesion between the nanofibers and the substrate. In this report, an amine-hardened epoxy resin was selected as an adhesion agent to weld nanofiber junctions and improve the interfacial adhesion performance. It was confirmed that the physical properties of the nanofibers were greatly improved after the crosslinking welding process. Taking advantage of the welding process, field-effect transistors (FETs) based on In2O3 nanofiber networks (NFNs) with various nanofiber densities were integrated and investigated. It was found that the FETs based on In2O3 NFNs with a nanofiber density of 0.4 µm-1 exhibited the optimal electrical performance. When high-k ZrOx was integrated into the FETs as the dielectric layer, the FETs based on In2O3 NFNs/ZrOx exhibited superior performance, including a µFE of 13.2 cm2 V-1 s-1, an Ion/Ioff of 107, and an SS of 90 mV per decade. The crosslinking welding process is a simple, versatile and low-cost technique, which has great possibility for various applications.

5.
Nanoscale ; 10(30): 14712-14718, 2018 Aug 02.
Article in English | MEDLINE | ID: mdl-30043022

ABSTRACT

One-dimensional (1D) nanofibers have been considered to be important building blocks for nano-electronics due to their superior physical and chemical properties. In this report, high-performance zinc tin oxide (ZnSnO) nanofibers with various composition ratios were prepared by electrospinning. The surface morphology, crystallinity, grain size distribution, and chemical composition of the nanofibers were investigated. Meanwhile, field-effect transistors (FETs) based on ZnSnO nanofiber networks (NFNs) with various composition ratios were integrated and investigated. For optimized Zn0.3Sn0.7O NFNs FETs, the device based on an SiO2 dielectric exhibited a high electrical performance, including a high on/off current ratio (Ion/off) of 2 × 107 and a field-effect mobility (µFE) of 0.17 cm2 V-1 s-1. When a high-permittivity (κ) ZrOx thin film was employed as the dielectric in Zn0.3Sn0.7O NFNs FETs, the operating voltage was substantially reduced and a high µFE of 7.8 cm2 V-1 s-1 was achieved. These results indicate that the Zn0.3Sn0.7O NFNs/ZrOx FETs exhibit great potency in low-cost and low-voltage devices.

6.
ACS Appl Mater Interfaces ; 10(24): 20703-20711, 2018 Jun 20.
Article in English | MEDLINE | ID: mdl-29799183

ABSTRACT

Recently, semiconducting nanofiber networks (NFNs) have been considered as one of the most promising platforms for large-area and low-cost electronics applications. However, the high contact resistance among stacking nanofibers remained to be a major challenge, leading to poor device performance and parasitic energy consumption. In this report, a controllable welding technique for NFNs was successfully demonstrated via a bioinspired capillary-driven process. The interfiber connections were well-achieved via a cooperative concept, combining localized capillary condensation and curvature-induced surface diffusion. With the improvements of the interfiber connections, the welded NFNs exhibited enhanced mechanical property and high electrical performance. The field-effect transistors (FETs) based on the welded Hf-doped In2O3 (InHfO) NFNs were demonstrated for the first time. Meanwhile, the mechanisms involved in the grain-boundary modulation for polycrystalline metal-oxide nanofibers were discussed. When the high-k ZrO x dielectric thin films were integrated into the FETs, the field-effect mobility and operating voltage were further improved to be 25 cm2 V-1 s-1 and 3 V, respectively. This is one of the best device performances among the reported nanofibers-based FETs. These results demonstrated the potencies of the capillary-driven welding process and grain-boundary modulation mechanism for metal-oxide NFNs, which could be applicable for high-performance, large-scale, and low-power functional electronics.

7.
ACS Appl Mater Interfaces ; 10(21): 18057-18065, 2018 May 30.
Article in English | MEDLINE | ID: mdl-29733184

ABSTRACT

Technical development for thin-film fabrication is essential for emerging metal-oxide (MO) electronics. Although impressive progress has been achieved in fabricating MO thin films, the challenges still remain. Here, we report a versatile and general thermal-induced nanomelting technique for fabricating MO thin films from the fiber networks, briefly called fiber-to-film (FTF) process. The high quality of the FTF-processed MO thin films was confirmed by various investigations. The FTF process is generally applicable to numerous technologically relevant MO thin films, including semiconducting thin films (e.g., In2O3, InZnO, and InZrZnO), conducting thin films (e.g., InSnO), and insulating thin films (e.g., AlO x). By optimizing the fabrication process, In2O3/AlO x thin-film transistors (TFTs) were successfully integrated by fully FTF processes. High-performance TFT was achieved with an average mobility of ∼25 cm2/(Vs), an on/off current ratio of ∼107, a threshold voltage of ∼1 V, and a device yield of 100%. As a proof of concept, one-transistor-driven pixel circuit was constructed, which exhibited high controllability over the light-emitting diodes. Logic gates based on fully FTF-processed In2O3/AlO x TFTs were further realized, which exhibited good dynamic logic responses and voltage amplification by a factor of ∼4. The FTF technique presented here offers great potential in large-area and low-cost manufacturing for flexible oxide electronics.

8.
ACS Appl Mater Interfaces ; 10(31): 25841-25849, 2018 Aug 08.
Article in English | MEDLINE | ID: mdl-28937205

ABSTRACT

One-dimensional metal-oxide nanowires are regarded as important building blocks in nanoscale electronics, because of their unique mechanical and electrical properties. In this work, p-type nickel oxide nanowires (NiO NWs) were fabricated by combining sol-gel and electrospinning processes. The poly(vinylpyrrolidone) (PVP) with a molecular weight of 1 300 000 was used as the polymer matrix to increase the viscosity of a NiO precursor solution. The formation and properties of the as-spun NiO/PVP composite NWs before/after calcination treatment were investigated using various techniques. Because of the enhanced adhesion properties between ultraviolet (UV)-treated NiO NWs and the substrate, the field-effect transistors (FETs) based on NiO NWs were found to exhibit satisfying p-channel behaviors. For the fabrication of aligned NiO NW arrays, two parallel conducting Si strips were grounded as NW collector. The integrated FETs based on aligned NiO NWs were demonstrated to exhibit superior electrical performance, compared to the disordered counterparts with the comparable NW coverage. By employing high- k aluminum oxide (Al2O3) as a dielectric layer, instead of conventional SiO2, the devices with an aligned NiO NW array exhibit a high hole mobility of 2.8 cm2/(V s) with a low operating voltage of 5 V, fast switching speed, and successful modulation of light emission over external light-emitting diodes. To the best of our knowledge, this is the first work demonstrating the low-voltage transistors based on p-type oxide NWs, which represents a great step toward the development of sensors and CMOS logic circuits.

9.
Adv Mater ; 29(34)2017 Sep.
Article in English | MEDLINE | ID: mdl-28691310

ABSTRACT

Low-temperature solution processing opens a new window for the fabrication of oxide semiconductors due to its simple, low cost, and large-area uniformity. Herein, by using solution combustion synthesis (SCS), p-type Cu-doped NiO (Cu:NiO) thin films are fabricated at a temperature lower than 150 °C. The light doping of Cu substitutes the Ni site and disperses the valence band of the NiO matrix, leading to an enhanced p-type conductivity. Their integration into thin-film transistors (TFTs) demonstrates typical p-type semiconducting behavior. The optimized Cu5% NiO TFT exhibits outstanding electrical performance with a hole mobility of 1.5 cm2 V-1 s-1 , a large on/off current ratio of ≈104 , and clear switching characteristics under dynamic measurements. The employment of a high-k ZrO2 gate dielectric enables a low operating voltage (≤2 V) of the TFTs, which is critical for portable and battery-driven devices. The construction of a light-emitting-diode driving circuit demonstrates the high current control capability of the resultant TFTs. The achievement of the low-temperature-processed Cu:NiO thin films via SCS not only provides a feasible approach for low-cost flexible p-type oxide electronics but also represents a significant step toward the development of complementary metal-oxide semiconductor circuits.

10.
ACS Appl Mater Interfaces ; 9(12): 10805-10812, 2017 Mar 29.
Article in English | MEDLINE | ID: mdl-28264156

ABSTRACT

Electrospun metal oxide nanofibers have been regarded as promising blocks for large-area, low-cost, and one-dimensional electronic devices. However, the electronic devices based on electrospun nanofibers usually suffer from poor performance and inferior viability. Here, we report an efficient photochemical process using UV light generated by a high-pressure mercury lamp to promote the electrical performance of the nanofiber-based electronic devices. Such UV treatment can lead to strong photochemical activation of electrospun nanofibers, and therefore, a stable adherent nanofiber network and electronic-clean interface were formed. By use of UV treatment, high-performance indium oxide (In2O3) nanofiber based field-effect transistors (FETs) with highly efficient modulation of electrical characteristics have been successfully fabricated. To reduce the operating voltage and further improve the device performance, the In2O3 nanofiber FETs based on solution-processed high-k AlOx dielectrics were integrated and investigated. The as-fabricated In2O3/AlOx FETs exhibit superior electrical performance, including a high mobility of 19.8 cm2 V-1 s-1, a large on/off current ratio of 106, and high stability over time and cycling. The improved performance of the UV-treated FETs was further confirmed by the integration of the electrospun In2O3/AlOx FETs into inverters. This work presents an important advance toward the practical applications of electrospun nanofibers for functional electronic devices.

11.
Appl Opt ; 54(15): 4812-9, 2015 May 20.
Article in English | MEDLINE | ID: mdl-26192519

ABSTRACT

In order to develop a method to analyze metal elements in thin-film samples rapidly, directly and without sample preparation, and to understand the mechanism of laser-film interaction and plasma formation and evolution, a laboratory laser-induced breakdown spectroscopy system was established recently for nanometer-film analysis. ZrO(2) films prepared on silicon chips by a sol-gel process were employed in the following experiment and their thickness was about 40 nm. By the initial investigation that we carried out, the stability of this system was verified and the relative standard deviation of the target peak was found to be lower than 1.6% with the help of a position system. The influences of different experimental parameters, such as laser energy, laser focus to sample distance (LFTSD) settings, and gate delay, were studied under conditions of room temperature and atmospheric pressure. The experimental results show that the LFTSD was one of the most important parameters for plasma formation and spectral collection in comparison with other parameters by means of plasma spectra and images. So the effects of the LFTSD on the spectra, plasma evolution, and craters are specially discussed in this paper. At last, we calculated the plasma temperature and electron density under optimal parameters for quantitative analysis. The result shows that the established system is available for qualitative and quantitative analysis of films under conditions of single pulse and low ablation energy.

SELECTION OF CITATIONS
SEARCH DETAIL
...