Nucleotide sequence and strand displacement amplification of the 70K protein gene from mycobacteria.

We isolated and determined the nucleotide sequence of the 70K gene from nine mycobacteria and from two related non-mycobacteria with the goal of obtaining a region of requisite specificity to serve as a mycobacterial genus-specific probe. Two different primer sets were then designed to amplify the 70K gene using strand displacement amplification. Using one of the primer sets, 10 different mycobacteria were readily detected with sensitivities of 100 molecules DNA, and with only cross-reactivity to two non-mycobacteria. The other set of primers that were tested amplified the same set of mycobacteria, but exhibited no crossreactivity with non-mycobacterial DNAs. By employing one of the primer sets, we were able to successfully amplify with high sensitivity three different target DNA sequences comprised of the 70K mycobacterial genus target, an IS 6110 (M. tuberculosis complex) target, and an internal amplification control using SDA. These results demonstrate the potential of the 70K gene to serve as a mycobacterial genus-specific probe, and demonstrate the first multiplex amplification by SDA of three DNA targets.

Multiplex strand displacement amplification (SDA) and detection of DNA sequences from Mycobacterium tuberculosis and other mycobacteria.

Strand Displacement Amplification (SDA) is an isothermal, in vitro method of amplifying a DNA target sequence prior to detection [Walker et al (1992) Nucleic Acids Res., 20, 1691-1693]. Here we describe a multiplex form of SDA that allows two target sequences and an internal amplification control to be co-amplified by a single pair of primers after common priming sequences are spontaneously appended to the ends of target fragments. Multiplex SDA operates at a single temperature, under the same simple protocol previously developed for single-target SDA. We applied multiplex SDA to co-amplification of a target sequence (IS6110) that is specific to members of the Mycobacterium tuberculosis-complex and a target (16S ribosomal gene) that is common to most clinically relevant species of mycobacteria. Both targets are amplified 10(8)-fold during a 2 hour, single temperature incubation. The relative sensitivity of the system was evaluated across a number of clinically relevant mycobacteria and checked for crossreactivity against organisms that are closely related to mycobacteria.

Chemiluminescent detection of strand displacement amplified DNA from species comprising the Mycobacterium tuberculosis complex.

Strand displacement amplification, a new isothermal in vitro DNA amplification technique, was used to amplify target DNA contained within the IS6110 insertion element of the species within the Mycobacterium complex (Mycobacterium tuberculosis, M. bovis, M. bovis-BCG, M. africanum and M. microti). The target nucleic acid sequence is present in approximately ten, two, one, five and five copies in M. tuberculosis, M. bovis, M. bovis-BCG, M. africanum and M. microti, respectively. Amplified products were detected using a non-isotopic microtitre plate assay employing a biotinylated oligodeoxynucleotide probe and an alkaline phosphatase conjugated oligodeoxynucleotide probe. Lumiphos 530 was the chemiluminescent substrate for alkaline phosphatase. The combination of the strand displacement amplification method with this sensitive and rapid (less than 2 h) detection system resulted in the specific detection of as few as 1-25 initial IS6110 targets in the five Mycobacterium complex species based on signal/noise criteria. Negative results were obtained with eight other Mycobacterium species as well as with 32 non-Mycobacterium species.

Isothermal in vitro amplification of DNA by a restriction enzyme/DNA polymerase system.

An isothermal in vitro DNA amplification method was developed based upon the following sequence of reaction events. Restriction enzyme cleavage and subsequent heat denaturation of a DNA sample generates two single-stranded target DNA fragments (T1 and T2). Present in excess are two DNA amplification primers (P1 and P2). The 3' end of P1 binds to the 3' end of T1, forming a duplex with 5' overhangs. Likewise, P2 binds to T2. The 5' overhangs of P1 and P2 contain a recognition sequence (5'-GTTGAC-3') for the restriction enzyme HincII. An exonuclease-deficient form of the large fragment of Escherichia coli DNA polymerase I (exo- Klenow polymerase) [Derbyshire, V., Freemont, P. S., Sanderson, M. R., Beese, L., Friedman, J. M., Joyce, C. M. & Steitz, T. A. (1988) Science 240, 199-201] extends the 3' ends of the duplexes using dGTP, dCTP, TTP, and deoxyadenosine 5'-[alpha-thio]triphosphate, which produces hemiphosphorothioate recognition sites on P1.T1 and P2.T2. HincII nicks the unprotected primer strands of the hemiphosphorothioate recognition sites, leaving intact the modified complementary strands. The exo- Klenow polymerase extends the 3' end at the nick on P1.T1 and displaces the downstream strand that is functionally equivalent to T2. Likewise, extension at the nick on P2.T2 results in displacement of a downstream strand functionally equivalent to T1. Nicking and polymerization/displacement steps cycle continuously on P1.T1 and P2.T2 because extension at a nick regenerates a nickable HincII recognition site. Target amplification is exponential because strands displaced from P1.T1 serve as targets for P2 and strands displaced from P2.T2 serve as targets for P1. A 10(6)-fold amplification of a genomic sequence from Mycobacterium tuberculosis or Mycobacterium bovis was achieved in 4 h at 37 degrees C.