An SPS-RS Technique for the Fabrication of SrMoO4 Powellite Mineral-like Ceramics for 90Sr Immobilization.

This paper reports a method for the fabrication of mineral-like SrMoO4 ceramics with a powellite structure, which is promising for the immobilization of the high-energy 90Sr radioisotope. The reported method is based on the solid-phase "in situ" interaction between SrO and MoO3 oxides initiated under spark plasma sintering (SPS) conditions. Dilatometry, XRD, SEM, and EDX methods were used to investigate the consolidation dynamics, phase formation, and structural changes in the reactive powder blend and sintered ceramics. The temperature conditions for SrMoO4 formation under SPS were determined, yielding ceramics with a relative density of 84.0-96.3%, Vickers microhardness of 157-295 HV, and compressive strength of 54-331 MPa. Ceramic samples demonstrate a low Sr leaching rate of 10-6 g/cm2·day, indicating a rather high hydrolytic stability and meeting the requirements of GOST R 50926-96 imposed on solid radioactive wastes. The results presented here show a wide range of prospects for the application of ceramic matrixes with the mineral-like composition studied here to radioactive waste processing and radioisotope manufacturing.

CaSiO3-HAp Metal-Reinforced Biocomposite Ceramics for Bone Tissue Engineering.

Reconstructive and regenerative bone surgery is based on the use of high-tech biocompatible implants needed to restore the functions of the musculoskeletal system of patients. Ti6Al4V is one of the most widely used titanium alloys for a variety of applications where low density and excellent corrosion resistance are required, including biomechanical applications (implants and prostheses). Calcium silicate or wollastonite (CaSiO3) and calcium hydroxyapatite (HAp) is a bioceramic material used in biomedicine due to its bioactive properties, which can potentially be used for bone repair. In this regard, the research investigates the possibility of using spark plasma sintering technology to obtain new CaSiO3-HAp biocomposite ceramics reinforced with a Ti6Al4V titanium alloy matrix obtained by additive manufacturing. The phase and elemental compositions, structure, and morphology of the initial CaSiO3-HAp powder and its ceramic metal biocomposite were studied by X-ray fluorescence, scanning electron microscopy, energy-dispersive X-ray spectroscopy, and Brunauer-Emmett-Teller analysis methods. The spark plasma sintering technology was shown to be efficient for the consolidation of CaSiO3-HAp powder in volume with a Ti6Al4V reinforcing matrix to obtain a ceramic metal biocomposite of an integral form. Vickers microhardness values were determined for the alloy and bioceramics (~500 and 560 HV, respectively), as well as for their interface area (~640 HV). An assessment of the critical stress intensity factor KIc (crack resistance) was performed. The research result is new and represents a prospect for the creation of high-tech implant products for regenerative bone surgery.

Synthetic Calcium Silicate Biocomposite Based on Sea Urchin Skeleton for 5-Fluorouracil Cancer Delivery.

Synthetic calcium silicates and phosphates are promising compounds for targeted drug delivery for the effective treatment of cancerous tumors, and for minimizing toxic effects on the patient's entire body. This work presents an original synthesis of a composite based on crystalline wollastonite CaSiO3 and combeite Na4Ca4(Si6O18), using a sea urchin Mesocentrotus nudus skeleton by microwave heating under hydrothermal conditions. The phase and elemental composition and structure of the obtained composite were studied by XRF, REM, BET, and EDS methods, depending on the microwave heating time of 30 or 60 min, respectively, and the influence of thermo-oxidative post-treatment of samples. The role of the sea urchin skeleton in the synthesis was shown. First, it provides a raw material base (source of Ca2+) for the formation of the calcium silicate composite. Second, it is a matrix for the formation of its porous inorganic framework. The sorption capacity of the composite, with respect to 5-fluorouracil, was estimated, the value of which was 12.3 mg/L. The resulting composite is a promising carrier for the targeted delivery of chemotherapeutic drugs. The mechanism of drug release from an inorganic natural matrix was also evaluated by fitting its release profile to various mathematical models.

Ce3+, Pr3+ Co-Doped Lu3Al5O12 Single Crystals and Ceramics: A Comparative Study.

Ce3+, Pr3+ co-doped Lu3Al5O12 (Ce, Pr:LuAG) single crystals and ceramics were prepared using the optical floating zone (OFZ) and reactive vacuum sintering methods, respectively. The microstructure, photo- (λex = 450 nm), and radio-luminescence (under X-ray excitation) performance, as well as scintillation light yield (LY, under γ-ray, 137Cs source) of both materials, were investigated and compared. Ce, Pr:LuAG ceramics had an in-line transmittance of approximately 20% in the visible light range, while the analogous crystals were more transparent (~65%). The X-ray excited luminescent (XEL) spectra showed the characteristic Ce 3+ and Pr3+ emissions located at 310 nm, 380 nm, and 510 nm. The highest LY of the Ce, Pr:LuAG ceramics reached 34,112 pho/MeV at 2 µs time gate, which is higher than that of a single crystal. The ratio of LY values (LY2/LY0.75) between shaping times of 0.75 µs and 2 µs indicated a faster scintillation decay of ceramics regarding single crystals. It was ascribed to the lower effective concentration of luminescent activators in single crystals because of the coefficient segregation effect.

Adsorption of Co(II) ions using Zr-Ca-Mg and Ti-Ca-Mg phosphates: adsorption modeling and mechanistic aspects.

The environmental pollution by toxic Co(II) ions had a negative impact on living organisms and water resources. The amorphous Zr-Ca-Mg and Ti-Ca-Mg phosphates with varied Zr and Ti content with the mesoporous structure (ABET = 19-232 m2/g, Vdes. = 0.075-0.370 cm3/g, Ddes. = 6.2-10.9 nm) were synthesized. The effect of adsorbent chemical composition, the presence of competing ions (0.1-1.0 M NaCl and 0.01-0.1 M CaCl2 backgrounds), and pH (3.0-7.0) of aqueous solution on adsorption removal of Co(II) ions by Zr-Ca-Mg and Ti-Ca-Mg phosphates was studied. The highest adsorption capacity of Zr-Ca-Mg-1 and Ti-Ca-Mg-1 samples reached 253.3 and 212.8 mg/g. The prepared adsorbents demonstrated high efficiency at pH in the range of 3.0-7.0 and the presence of 0.1-1.0 M NaCl and seawater with a salinity of 35.0 g/L backgrounds. The chemisorption and ion-exchange mechanisms of Co(II) ions removal for Zr-Ca-Mg and Ti-Ca-Mg phosphates were proposed. The adsorption isotherms were well fitted with Sips and Langmuir models that proved the heterogeneous nature of adsorption sites as well as assumed the monolayer adsorption that occurs at specific homogeneous sites within the adsorbent without any interaction between the adsorbed substances. The kinetic data was well described by the pseudo-second-order model that is suitable for chemisorption processes as liming adsorption stage. The presented results shown the prospects of developed adsorbents for the investigation of real wastewater treatment from heavy metal ions and liquid radioactive waste purification.

Wide Concentration Range of Tb3+ Doping Influence on Scintillation Properties of (Ce, Tb, Gd)3Ga2Al3O12 Crystals Grown by the Optical Floating Zone Method.

To obtain a deeper understand of the energy transfer mechanism between Ce3+ and Tb3+ ions in the aluminum garnet hosts, (Ce, Tb, Gd)3Ga2Al3O12 (GGAG:Ce, Tb) single crystals grown by the optical floating zone (OFZ) method were investigated systematically in a wide range of Tb3+ doping concentration (1-66 at.%). Among those, crystal with 7 at.% Tb reached a single garnet phase while the crystals with other Tb3+ concentrations are mixed phases of garnet and perovskite. Obvious Ce and Ga loss can be observed by an energy dispersive X-ray spectroscope (EDS) technology. The absorption bands belonging to both Ce3+ and Tb3+ ions can be observed in all crystals. Photoluminescence (PL) spectra show the presence of an efficient energy transfer from the Tb3+ to Ce3+ and the gradually quenching effect with increasing of Tb3+ concentration. GGAG: 1% Ce3+, 7% Tb3+ crystal was found to possess the highest PL intensity under excitation of 450 nm. The maximum light yield (LY) reaches 18,941 pho/MeV. The improved luminescent and scintillation characteristics indicate that the cation engineering of Tb3+ can optimize the photoconversion performance of GGAG:Ce.

Morphological Characteristics of the Osteoplastic Potential of Synthetic CaSiO3/HAp Powder Biocomposite.

The study describes the influence of synthetic CaSiO3/HAp powder biocomposite on the process of regeneration in osseous tissue in the alveolar ridges in terms of the morphological characteristics of the osteoplastic potential. The authors investigated the osteoinduction and osteoconduction "in vivo" processes during bone tissue regeneration in the mandible defect area of an experimental animal (rabbit). The possibility of angiogenesis in the graft as an adaptation factor was studied in the process of bone tissue regeneration. The results of the histological study that included the qualitative parameters of bone tissue regeneration, the morphometric parameters (microarchitectonics) of the bone, the parameters of osteosynthesis (thickness of the osteoid plates), and resorption (volume density of the eroded surface) were presented. The results allowed the authors to characterize the possibility of the practical adaptation for synthetic powder biocomposite as an osteoplastic graft for the rehabilitation of osseous defects in dentistry.

CaSiO3-HAp Structural Bioceramic by Sol-Gel and SPS-RS Techniques: Bacteria Test Assessment.

The article presents an original way of getting porous and mechanically strong CaSiO3-HAp ceramics, which is highly desirable for bone-ceramic implants in bone restoration surgery. The method combines wet and solid-phase approaches of inorganic synthesis: sol-gel (template) technology to produce the amorphous xonotlite (Ca6Si6O17·2OH) as the raw material, followed by its spark plasma sintering-reactive synthesis (SPS-RS) into ceramics. Formation of both crystalline wollastonite (CaSiO3) and hydroxyapatite (Ca10(PO4)6(OH)2) occurs "in situ" under SPS conditions, which is the main novelty of the method, due to combining the solid-phase transitions of the amorphous xonotlite with the chemical reaction within the powder mixture between CaO and CaHPO4. Formation of pristine HAp and its composite derivative with wollastonite was studied by means of TGA and XRD with the temperatures of the "in situ" interactions also determined. A facile route to tailor a macroporous structure is suggested, with polymer (siloxane-acrylate latex) and carbon (fibers and powder) fillers being used as the pore-forming templates. Microbial tests were carried out to reveal the morphological features of the bacterial film Pseudomonas aeruginosa that formed on the surface of the ceramics, depending on the content of HAp (0, 20, and 50 wt%).