Tailoring an Interface Microstructure for High-Performance Reversible Protonic Ceramic Electrochemical Cells via Soft Lithography.

Micropatterning is considered a promising strategy for improving the performance of electrochemical devices. However, micropatterning on ceramic is limited by its mechanically fragile properties. This paper reports a novel imprinting-assisted transfer technique to fabricate an interlayer structure in a protonic ceramic electrochemical cell with a micropatterned electrolyte. A dense proton-conducting electrolyte, BaCe0.7Zr0.1Y0.1Yb0.1O3-δ, is micropatterned in a chevron shape with the highest aspect ratio of patterns in electrode-supported cells to the best of our knowledge, increasing surface areas of both electrode sides more than 40%. The distribution of relaxation time analysis reveals that the chevron-patterned electrolyte layer significantly increases the electrode contact areas and active electrochemical reaction sites at the vicinity of the interfaces, contributing to enhanced performances of both the fuel cell and electrolysis operations. The patterned cell demonstrates improved fuel cell performance (>45%) and enhances electrolysis cell performance (30%) at 500 °C. This novel micropatterning technique is promising for the facile production of layered electrochemical cells, further opening a new route for the performance enhancement of ceramic-based electrochemical cells.

Vapor-Mediated Infiltration of Nanocatalysts for Low-Temperature Solid Oxide Fuel Cells Using Electrosprayed Dendrites.

Electrode architecturing for fast electrochemical reaction is essential for achieving high-performance of low-temperature solid oxide fuel cells (LT-SOFCs). However, the conventional droplet infiltration technique still has limitations in terms of the applicability and scalability of nanocatalyst implementation. Here, we develop a novel two-step precursor infiltration process and fabricate high-performance LT-SOFCs with homogeneous and robust nanocatalysts. This novel infiltration process is designed based on the principle of a reversible sol-gel transition where the gelated precursor dendrites are uniformly deposited onto the electrode via controlled nanoscale electrospraying process then resolubilized and infiltrated into the porous electrode structure through subsequent humidity control. Our infiltration technique reduces the cathodic polarization resistance by 18% compared to conventional processes, thereby achieving an enhanced peak power density of 0.976 W cm-2 at 650 °C. These results, which provide various degrees of freedom for forming nanocatalysts, exhibit an advancement in LT-SOFC technology.

Quantitative determination of lithium depletion during rapid cycling in sulfide-based all-solid-state batteries.

We propose a promising electrochemical analysis tool based on the distribution of relaxation times (DRT) to quantify interfacial resistances towards a comprehensive understanding of complex solid-state interfacial phenomena in sulfide-based all-solid-state batteries (ASSBs). Using DRT-assisted impedance analysis, we identify a new resistance component in the range of 102-103 Hz of 3.5 and 0.9 Ω in the absence and presence of a LiNbO3 layer, respectively, at 1C-rate. Experimental and computational studies confirm that this interfacial resistance results from lithium depletion in sulfide solid electrolytes. Furthermore, we expect our approach to provide new insights into complex interfacial phenomena in ASSBs.

Functionalized Sulfide Solid Electrolyte with Air-Stable and Chemical-Resistant Oxysulfide Nanolayer for All-Solid-State Batteries.

Sulfide solid electrolytes (SEs) with high Li-ion conductivities (σion) and soft mechanical properties have limited applications in wet casting processes for commercial all-solid-state batteries (ASSBs) because of their inherent atmospheric and chemical instabilities. In this study, we fabricated sulfide SEs with a novel core-shell structure via environmental mechanical alloying, while providing sufficient control of the partial pressure of oxygen. This powder possesses notable atmospheric stability and chemical resistance because it is covered with a stable oxysulfide nanolayer that prevents deterioration of the bulk region. The core-shell SEs showed a σion of more than 2.50 mS cm-1 after air exposure (for 30 min) and reaction with slurry chemicals (mixing and drying for 31 min), which was approximately 82.8% of the initial σion. The ASSB cell fabricated through wet casting provided an initial discharge capacity of 125.6 mAh g-1. The core-shell SEs thus exhibited improved powder stability and reliability in the presence of chemicals used in various wet casting processes for commercial ASSBs.

Ultrasensitive mechanical crack-based sensor inspired by the spider sensory system.

Recently developed flexible mechanosensors based on inorganic silicon, organic semiconductors, carbon nanotubes, graphene platelets, pressure-sensitive rubber and self-powered devices are highly sensitive and can be applied to human skin. However, the development of a multifunctional sensor satisfying the requirements of ultrahigh mechanosensitivity, flexibility and durability remains a challenge. In nature, spiders sense extremely small variations in mechanical stress using crack-shaped slit organs near their leg joints. Here we demonstrate that sensors based on nanoscale crack junctions and inspired by the geometry of a spider's slit organ can attain ultrahigh sensitivity and serve multiple purposes. The sensors are sensitive to strain (with a gauge factor of over 2,000 in the 0-2 per cent strain range) and vibration (with the ability to detect amplitudes of approximately 10 nanometres). The device is reversible, reproducible, durable and mechanically flexible, and can thus be easily mounted on human skin as an electronic multipixel array. The ultrahigh mechanosensitivity is attributed to the disconnection-reconnection process undergone by the zip-like nanoscale crack junctions under strain or vibration. The proposed theoretical model is consistent with experimental data that we report here. We also demonstrate that sensors based on nanoscale crack junctions are applicable to highly selective speech pattern recognition and the detection of physiological signals. The nanoscale crack junction-based sensory system could be useful in diverse applications requiring ultrahigh displacement sensitivity.

A histomorphometric study on collagen-apatite composite as a graft material: the influence of gap size at the titanium-bone interface in animal model.

The purpose of this study was to evaluate the healing process of collagen-apatite composite (CAC) at the titanium-bone interface in animal model. Small gaps (0.5 or 1.0 mm-sized wells) were prepared in the epoxy-resin block implants coated with pure titanium. The gaps were filled with CAC or demineralized freeze-dried bone (DFDB). The titanium-coated epoxy-resin block implants were inserted in the tibia of rabbit for 4 weeks or 8 weeks. The microscopic features of bony healing process in the grafted gaps were examined and analyzed. In the histomorphometric analysis, CAC group showed higher fraction of newly-formed bone than DFDB group in both 0.5 and 1.0 mm gap subgroup at 4-week specimen (P < 0.05). In the transmission electron microscopic examinations, osteoblasts of the newly-formed bone of CAC group showed more cellular activity than that of DFDB group. From the results, it was expected that CAC had more beneficial property on early bony healing process than DFDB at the titanium-bone interface.