Electrothermal instability mitigation by using thick dielectric coatings on magnetically imploded conductors.

Recent experiments on Sandia's Z facility have confirmed simulation predictions of dramatically reduced instability growth in solid metallic rods when thick dielectric coatings are used to mitigate density perturbations arising from an electrothermal instability. These results provide further evidence that the inherent surface roughness as a result of target fabrication is not the dominant seed for the growth of magneto-Rayleigh-Taylor instabilities in liners with carefully machined smooth surfaces, but rather electrothermal instabilities that form early in the electrical current pulse as Joule heating melts and vaporizes the liner surface. These results suggest a new technique for substantially reducing the integral magneto-Rayleigh-Taylor instability growth in magnetically driven implosions, such as cylindrical dynamic material experiments and inertial confinement fusion concepts.

X-ray emission current scaling experiments for compact single-tungsten-wire arrays at 80-nanosecond implosion times.

We report the results of a series of current scaling experiments with the Z accelerator for the compact, single, 20-mm diameter, 10-mm long, tungsten-wire arrays employed for the double-ended hohlraum ICF concept [M. E. Cuneo, Plasma Phys. Controlled Fusion 48, R1 (2006)]. We measured the z -pinch peak radiated x-ray power and total radiated x-ray energy as a function of the peak current, at a constant implosion time tau_{imp}=80ns . Previous x-ray emission current scaling for these compact arrays was obtained at tau_{imp}=95ns in the work of Stygar [Phys. Rev. E 69, 046403 (2004)]. In the present study we utilized lighter single-tungsten-wire arrays. For all the measurements, the load hardware dimensions, materials, and array wire number (N=300) were kept constant and were the same as the previous study. We also kept the normalized load current spatial and temporal profiles the same for all experiments reported in this work. Two different currents, 11.2+/-0.2MA and 17.0+/-0.3MA , were driven through the wire arrays. The average peak x-ray power for these compact wire arrays increased by 26%+/-7%to158+/-26TW at 17+/-0.3MA from the 125+/-24TW obtained at a peak current of 18.8+/-0.5MA with tau_{imp}=95ns . The higher peak power of the faster implosions may possibly be attributed to a higher implosion velocity, which in turn improves the implosion stability, and/or to shorter wire ablation times, which may lead to a decrease in trailing mass and trailing current. Our results show that the scaling of the radiated x-ray peak power and total radiated x-ray energy scaling with peak drive current to be closer to quadratic than the results of Stygar We find that the x-ray peak radiated power is P_{r} proportional, variantI;{1.57+/-0.20} and the total x-ray radiated energy E_{r} proportional, variantI;{1.9+/-0.24} . We also find that the current scaling exponent of the power is sensitive to the inclusion of a single data point with a peak power at least 1.9sigma below the average. If we eliminate this particular shot from our analysis (shot 1608), the power and energy scaling becomes closer to quadratic. Namely, we find that the dependence on the peak load current of the peak x-ray radiated power and the total x-ray radiated energy become P_{r} proportional, variantI;{1.71+/-0.10} and E_{r} proportional, variantI;{2.01+/-0.21} , respectively. In this case, the power scaling exponent is different by more than 2sigma from the previously published results of Stygar Larger data sets are likely required to resolve this uncertainty and eliminate the sensitivity to statistical fluctuations in any future studies of this type. Nevertheless, with or without the inclusion of shot 1608, our results with tau_{imp}=80ns fall short of an I2 scaling of the peak x-ray radiated power by at least 2sigma . In either case, the results of our study are consistent with the heuristic wire ablation model proposed by Stygar (P_{r} proportional, variantI;{1.5}) . We also derive an empirical predictive relation that connects the power scaling exponent with certain array parameters.

Evaluation of bent-crystal x-ray backlighting and microscopy techniques for the Sandia Z machine.

X-ray backlighting and microscopy systems for the 1-10-keV range based on spherically or toroidally bent crystals are discussed. These systems are ideal for use on the Sandia Z machine, a megajoule-class x-ray facility. Near-normal-incidence crystal microscopy systems have been shown to be more efficient than pinhole cameras with the same spatial resolution and magnification [Appl. Opt. 37, 1784 (1998)]. We show that high-resolution (< or = 10 microm) x-ray backlighting systems using bent crystals can be more efficient than analogous point-projection imaging systems. Examples of bent-crystal-backlighting results that demonstrate 10-microm resolution over a 20-mm field of view are presented.