ABSTRACT
The article presents selected issues related to material quality manufactured by selective laser sintering of AlSi10Mg alloy powder after milling. The workpiece was prepared and machined by down-milling and up-milling with tools made of high-speed steel. Breaches, pores and failure-like cracks on the machined surface were found, which negatively influenced the values of 3D surface roughness parameters. The occurring phenomena were analyzed and proposals for their explanation were made. The results of this research describe the effect of cutting parameters (the feed rate of f = 0.013-0.05 mm/tooth) on the values of parameters describing the surface quality and benchmarks. Topography measurements and 3D surface roughness parameters are presented, as well as the results of microscopic surface analysis. It was found that for aluminum alloy produced by the direct metal laser sintering (DMLS) method, the recommended machining method is down-milling.
ABSTRACT
This article presents selected issues related to the workpiece surface quality after machining by the laser sintering of AlSi10MG alloy powder. The surfaces of the workpiece were prepared and machined by longitudinal turning with tools made of sintered carbides. The occurrence of breaches on the machined material surface was found, which negatively influence the values of 3D surface roughness parameters. The occurring phenomena were analyzed and proposals for their explanation were made. Guidelines for the machining of workpieces achieved by the laser sintering of powders were developed. The lowest value of the 3D roughness parameters was obtained for f = 0.06 mm/rev, ap = 0.5-1.0 mm, and for the nose radius of cutting insert rε = 0.8 mm. The results of research on the effect of cutting parameters on the values of parameters describing the surface quality are presented. Topography measurements and 3D surface roughness parameters are presented, as well as the results of a microscopic 3D surface analysis. Taguchi's method was used in the research methodology.
ABSTRACT
This paper presents a method of acquisition and analysis of three-dimensional images in the task of automatic location and evaluation of defects on the surface of ceramic tiles. It presents a brief description of selected defects appearing on the surface of tiles, along with the analysis of their formation. The paper includes the presentation of the method of constructing a 3D image of the tile surface using the Laser Triangulation Method (LTM), along with the surface imaging parameters employed in the research. The algorithms of three-dimensional surface image analysis of ceramic tiles used in the process of image filtering and defect identification are presented. For selected defects, the method of measuring defect parameters and the method of visualization of defects on the surface are also presented. The developed method was tested on defective products to confirm its effectiveness in the field of quick defect detection in automated control systems installed on production lines.
ABSTRACT
We presented a novel approach to studies of the vascular grooves located on the inner surface of the cranial vault. A three-dimensional vision system that acquired the endocranial surface topography was used for this purpose. The acquired data were used to generate images showing the branching pattern of the middle meningeal artery. Fractal dimension was used to characterize and analyze branching pattern complexity. We discussed the usefulness of the latter method and indicated difficulties and potential errors connected to the fractal dimension application. The technique introduced for recording traits of the object surface appears to be helpful in anatomical study of morphological variation of dural vascularization. It may also be applicable in paleoneurological research based on analysis of the cranial remnants. Fractal dimension should be used carefully as a method sensitive to many aspects of data acquisition and processing.
Subject(s)
Imaging, Three-Dimensional/methods , Skull/anatomy & histology , Skull/blood supply , Anthropology, Physical , Female , Humans , Male , Neurosciences , Reproducibility of ResultsABSTRACT
In this paper we present potential usage of the 3D vision system for registering features of the macerated cranial bones. Applied 3D vision system collects height profiles of the object surface and from that data builds a three-dimensional image of the surface. This method appeared to be accurate enough to capture anatomical details of the macerated bones. With the aid of the 3D vision system we generated images of the surface of the human calvaria which was used for testing the system. Performed reconstruction visualized the imprints of the dural vascular system, cranial sutures, and the three-layer structure of the cranial bones observed in the cross-section. We figure out that the 3D vision system may deliver data which can enhance estimation of sex from the osteological material.
