Comparison of conventionally and naturally coloured coatings marked by laser technology for unique 2D coding of pharmaceuticals.

Substandard and/or falsified medicines are a growing global threat for health and they cause serious social and economic damage. In low- and middle-income countries the failure rate of these medical products is approximately 10.5%. 50% of medicines purchased over the Internet may be fake. According to Directive 2011/62/EU as regards the prevention of falsified medicines from entering into the legal supply chain, a unique identification should be put on each box of drugs in the EU from 9th February 2019. The current project is focusing on the development of a laser technology to mark an individual traceable code on the surface of the tablet. Usually, coatings contain titanium dioxide for sufficient coverage, which makes precision laser coding more difficult. New naturally coloured films do not include those excipients. In this research, we would like to compare the physical-chemical properties of conventionally and naturally coloured coatings after the laser marking procedure by using two types of lasers. This unique identification technology can be used for marking personalized medicine with the doses tailored for each patient, too. To sum up, the present findings may contribute to efficient and reliable laser marking solutions in the unique identification procedure. Based on our measurement results, it can be stated that excimer UV lasers are promising candidates as marking instruments for the polymer film in both conventionally and naturally coloured coatings.

Crystallization of Ge2Sb2Te5 thin films by nano- and femtosecond single laser pulse irradiation.

The amorphous to crystalline phase transformation of Ge2Sb2Te5 (GST) films by UV nanosecond (ns) and femtosecond (fs) single laser pulse irradiation at the same wavelength is compared. Detailed structural information about the phase transformation is collected by x-ray diffraction and high resolution transmission electron microscopy (TEM). The threshold fluences to induce crystallization are determined for both pulse lengths. A large difference between ns and fs pulse irradiation was found regarding the grain size distribution and morphology of the crystallized films. For fs single pulse irradiated GST thin films, columnar grains with a diameter of 20 to 60 nm were obtained as evidenced by cross-sectional TEM analysis. The local atomic arrangement was investigated by high-resolution Cs-corrected scanning TEM. Neither tetrahedral nor off-octahedral positions of Ge-atoms could be observed in the largely defect-free grains. A high optical reflectivity contrast (~25%) between amorphous and completely crystallized GST films was achieved by fs laser irradiation induced at fluences between 13 and 16 mJ/cm(2) and by ns laser irradiation induced at fluences between 67 and 130 mJ/cm(2). Finally, the fluence dependent increase of the reflectivity is discussed in terms of each photon involved into the crystallization process for ns and fs pulses, respectively.

Evaluation of laser-speckle contrast image analysis techniques in the cortical microcirculation of piglets.

A new laser speckle-contrast analysis (LASCA) technique based on multi-exposure imaging was employed to simultaneously study pial arteriolar responses with cerebrocortical perfusion changes to various vasodilator (5-10% CO(2) ventilation, bradykinin (1-10 µM), N-methyl-D-aspartate (100 µM)) vasoconstrictor (10-100 µM noradrenaline, 1M KCl), or neutral (2.1% H(2) ventilation) stimuli as well as to asphyxia in the newborn piglet. Anesthetized, ventilated animals (n=20) were fitted with closed cranial windows. Multiple exposure laser-speckle image series (1-100 ms) were obtained using a near infrared diode laser (λ=808 nm). The autocorrelation decay time (τ) of speckle fluctuations was determined over pial arterioles and parenchymal areas to express 1/τ being proportional to blood flow velocity by two different LASCA techniques: our novel multi-exposure or a single exposure (2 and 20 ms) approach. 1/τ values yielded by different LASCA techniques were not significantly different at most points. LASCA easily detected both increases and decreases in cortical blood flow (CoBF). Cortical 1/τ changes to hypercapnia closely matched quantitative CoBF data determined previously, and were also in accordance with increases of pial arteriolar blood flow, calculated from arteriolar flow velocity and cross sectional area changes. In summary, LASCA emerges as an appealing method to simultaneously study microvascular reactivity and cortical perfusion changes in the piglet.

Real correlation time measurement in laser speckle contrast analysis using wide exposure time range images.

In laser speckle contrast analysis (LASCA) used for imaging of blood flow, besides the moving blood cells, the speckle pattern is also influenced by the imaging system and scattering properties of the laser-illuminated static surface. A latex microsphere (650 nm size) emulsion was covered with scattering semitransparent materials (Teflon foils, tracing paper). Speckle images were recorded with different exposure times (0.2 ms-500 ms), and correlation times were determined by parameterizing the theoretical contrast-exposure time function. The correlation times obtained for covered and uncovered microsphere emulsions were in good agreement. The possibility of obtaining comparable, setup-independent results in blood perfusion monitoring can contribute to better applicability of LASCA.

Survival and proliferative ability of various living cell types after laser-induced forward transfer.

The survival, proliferation, and differentiation of freshly isolated and cultured cells were studied after absorbing film-assisted laser-induced forward transfer. Rat Schwann and astroglial cells and pig lens epithelial cells were used for transfer and the cells were cultured for 2 weeks after laser-pulsed transfer. All three cell types survived, proliferated, and differentiated under cell culture conditions and regained their original phenotype a few days after cell transfer. Time resolution studies have shown that the time required to accelerate the jets and droplets containing the cells was less than 1 micros and that the estimated minimum average acceleration of those ejected cells that reached a constant velocity was approximately 10(7) x g. This suggests that the majority of studied cells tolerated the extremely high acceleration at the beginning of the ejection and the deceleration during impact on the acceptor plate without significant damage to the original phenotype. These results suggest that the absorbing film-assisted laser-induced forward transfer technique appears to be suitable for several potential applications in tissue engineering and the biomedical tissue repair technologies.