ABSTRACT
Commercially available photovoltaic (PV) modules typically consist of individual silicon half-cut cells that are electrically interconnected. This interconnection method results in gaps between the cells, which do not contribute to the overall PV output power. One approach to enhance the cell-to-module power ratio is the placement of white, diffuse reflecting plastic material within these gaps. Conventionally, the process of generating reflective patterns involves several discrete steps, including film deposition, resist patterning, etching, and resist stripping. This study presents an innovative single-step procedure for the direct deposition of zinc reflective patterns onto glass substrates using laser-induced backward transfer (LIBT) and a nanosecond pulsed laser system. The process successfully produced lines and squares, demonstrating its versatility in achieving diverse geometric patterns under ambient atmospheric pressure and room temperature conditions. The evaluation of the transferred patterns included an examination of geometric dimensions and surface morphology using a 3D microscope and scanning electron microscopy (SEM) analysis at the air/Zn interface. Additionally, the thickness of the zinc film and its adhesion to the glass substrate were quantified. The angular reflectance at a wavelength of 660 nm for both the glass/Zn and air/Zn interfaces was measured.
ABSTRACT
The aim of this study was to examine the effect of the modified light spectrum of glass containing red luminophore on the performance of the photosynthetic apparatus of two types of lettuce cultivated in soil in a greenhouse. Butterhead and iceberg lettuce were cultivated in two types of greenhouses: (1) covered with transparent glass (control) and (2) covered with glass containing red luminophore (red). After 4 weeks of culture, structural and functional changes in the photosynthetic apparatus were examined. The presented study indicated that the red luminophore used changed the sunlight spectrum, providing an adequate blue:red light ratio, while decreasing the red:far-red radiation ratio. In such light conditions, changes in the efficiency parameters of the photosynthetic apparatus, modifications in the chloroplast ultrastructure, and altered proportions of structural proteins forming the photosynthetic apparatus were observed. These changes led to a decrease of CO2 carboxylation efficiency in both examined lettuce types.
Subject(s)
Chlorophyll , Photosynthesis , Chlorophyll/metabolism , Light , Chloroplasts/metabolism , Photosystem II Protein Complex/metabolism , Lactuca/metabolismABSTRACT
Low-cost metallic nanoink based on nickel-silver core-shell nanoparticles (Ni@Ag NPs) was used for the formation of conductive metallic coatings with low sintering temperature, which can be successfully applied for replacement of currently used silver-based nanoinks in printed electronics. The effect of oxalic acid (OA) on the sintering temperature and conductivity of coatings formed by Ni@Ag NPs was evaluated. It was found that the addition of OA to the ink formulation and post-printing treatment of deposited films with this acid provided a noticeable decrease in the sintering temperature required for obtaining conductive patterns that is especially important for utilizing the polymeric substrates. The obtained resistivity of metallic coatings after sintering at temperature as low as 100 °C was found to be 30 µΩ·cm, only ~4 times higher compared to the resistivity of bulk Ni that is promising for future application of such materials for fabrication of low-cost flexible printed patterns.
ABSTRACT
Cuprorivaite, also known as Egyptian blue (EB), CaCuSi4O10, has been utilized as an important blue pigment for thousands of years. It shows a 430-800 nm broad excitation band and an intense 910-920 nm near-infrared (NIR) emission peak at room temperature. The application that motivates the current research is for luminescent solar concentrator (LSC) usage. Current technology for this purpose relies on high near-infrared reflectance. This article addresses the investigation of the relationship between dispersing methods and photoluminescence (PL) intensity. Mechanical grinding methods investigated in the study were: horizontal bead mill, exfoliation and three-roll mill. The initial aim of the study was to verify if the proposed methods do not damage PL. To the surprise of the authors, three-roll mill treatment enhanced PL by nearly 50% without altering the morphology of the powder. An X-ray diffraction study suggested slight alterations in the crystal lattice.
