Ultrasonic evaluation of dental implant osseointegration.

Dental implants are widely used for oral rehabilitation. However, there remain risks of failure which are difficult to anticipate and depend on the implant osseointegration. The objective of this in vivo study is to determine the variation of the echographic ultrasonic response of a dental implant to bone healing around the implant interface. Twenty one dental implants were inserted in the femur of seven New Zealand white rabbits. Two animals were sacrificed after a healing duration of two weeks, three animals after six weeks and six animals after eleven weeks. The 10 MHz ultrasonic response of the implant was measured just after the implantation using a dedicated device positioned at the emerging surface of each dental implant. The measurements were realized again before the sacrifice with the same device. An indicator I˜ was derived based on the amplitude of the rf signal obtained for each configuration. The bone-Implant Contact (BIC) ratio was determined by histological analyses. The average value of the relative variation of the indicator I˜ obtained after initial surgery and after the corresponding healing period varies between 7% and 40%. A Kruskal-Wallis test (p<0.01) revealed a significant decrease of the value of the indicator I˜ as function of healing time. The indicator I˜ was significantly correlated (R(2)=0.45) with the BIC ratio. The results show that the ultrasonic response of a dental implant varies significantly as a function of healing time, which paves the way for the development of a new quantitative ultrasound (QUS) method in oral implantology.

Bone formation with deproteinized bovine bone mineral or biphasic calcium phosphate in the presence of autologous platelet lysate: comparative investigation in rabbit.

Bone substitutes alone or supplemented with platelet-derived concentrates are widely used to promote bone regeneration but their potency remains controversial. The aim of this study was, therefore, to compare the regenerative potential of preparations containing autologous platelet lysate (APL) and particles of either deproteinized bovine bone mineral (DBBM) or biphasic calcium phosphate (BCP), two bone substitutes with different resorption patterns. Rabbit APL was prepared by freeze-thawing a platelet suspension. Critical-size defects in rabbit femoral condyle were filled with DBBM or DBBM+APL and BCP or BCP+APL. Rabbits were sacrificed after six weeks and newly formed bone and residual implanted material were evaluated using nondemineralized histology and histomorphometry. New bone was observed around particles of all fillers tested. In the defects filled with BCP, the newly formed bone area was greater (70%; P < 0.001) while the residual material area was lower (60%; P < 0.001) than that observed in those filled with DBBM. New bone and residual material area of defects filled with either APL+DBBM or APL+BCP were similar to those observed in those filled with the material alone. In summary, osteoconductivity and resorption of BCP were greater than those of DBBM, while APL associated with either DBBM or BCP did not have an additional benefit.

Nanoindentation measurements of biomechanical properties in mature and newly formed bone tissue surrounding an implant.

The characterization of the biomechanical properties of newly formed bone tissue around implants is important to understand the osseointegration process. The objective of this study is to investigate the evolution of the hardness and indentation modulus of newly formed bone tissue as a function of healing time. To do so, a nanoindentation device is employed following a multimodality approach using histological analysis. Coin-shaped implants were placed in vivo at a distance of 200 µm from the cortical bone surface, leading to an initially empty cavity of 200 µm * 4.4 mm. Three New Zealand White rabbits were sacrificed after 4, 7, and 13 weeks of healing time. The bone samples were embedded and analyzed using histological analyses, allowing to distinguish mature and newly formed bone tissue. The bone mechanical properties were then measured in mature and newly formed bone tissue. The results are within the range of hardness and apparent Young's modulus values reported in previous literature. One-way ANOVA test revealed a significant effect of healing time on the indentation modulus (p < 0.001, F = 111.24) and hardness (p < 0.02, F = 3.47) of bone tissue. A Tukey-Kramer analysis revealed that the biomechanical properties of newly formed bone tissue (4 weeks) were significantly different from those of mature bone tissue. The comparison with the results obtained in Mathieu et al. (2011, "Micro-Brillouin Scattering Measurements in Mature and Newly Formed Bone Tissue Surrounding an Implant," J. Biomech. Eng., 133, 021006). shows that bone mass density increases by approximately 13.5% between newly formed bone (7 weeks) and mature bone tissue.

Mode III cleavage of a coin-shaped titanium implant in bone: effect of friction and crack propagation.

Endosseous cementless implants are widely used in orthopaedic, maxillofacial and oral surgery. However, failures are still observed and remain difficult to anticipate as remodelling phenomena at the bone-implant interface are poorly understood. The assessment of the biomechanical strength of the bone-implant interface may improve the understanding of the osseointegration process. An experimental approach based on a mode III cleavage mechanical device aims at understanding the behaviour of a planar bone-implant interface submitted to torsional loading. To do so, coin-shaped titanium implants were inserted on the tibiae of a New Zealand white rabbit for seven weeks. After the sacrifice, mode III cleavage experiments were performed on bone samples. An analytical model was developed to understand the debonding process of the bone-implant interface. The model allowed to assess the values of different parameters related to bone tissue at the vicinity of the implant with the additional assumption that bone adhesion occurs over around 70% of the implant surface, which is confirmed by microscopy images. The approach allows to estimate different quantities related to the bone-implant interface such as: torsional stiffness (around 20.5 N m rad(-1)), shear modulus (around 240 MPa), maximal torsional loading (around 0.056 N.m), mode III fracture energy (around 77.5 N m(-1)) and stress intensity factor (0.27 MPa m(1/2)). This study paves the way for the use of mode III cleavage testing for the investigation of torsional loading strength of the bone-implant interface, which might help for the development and optimization of implant biomaterial, surface treatment and medical treatment investigations.

Influence of healing time on the ultrasonic response of the bone-implant interface.

The aim of the present study is to investigate the effect of bone healing on the ultrasonic response of coin-shaped titanium implants inserted in rabbit tibiae. The ultrasound response of the interface was measured in vitro at 15 MHz after 7 and 13 weeks of healing time. The average value of the ratio r between the amplitudes of the echo of the bone-implant interface and of the water-implant interface was determined. The bone-implant contact (BIC) was measured by histomorphometry and the degree of mineralisation of bone was estimated qualitatively by histologic staining. The significant decrease of the ultrasonic quantitative indicator r (p = 2.10⁻4) vs. healing time (from r = 0.53 to r = 0.49) is explained by (1) the increase of the BIC (from 27% to 69%) and (2) the increase of mineralization of newly formed bone tissue, both phenomena inducing a decrease of the gap of acoustical impedance.

Numerical simulation of ultrasonic wave propagation for the evaluation of dental implant biomechanical stability.

Osseointegration of dental implants remains poorly understood. The objective of this numerical study is to understand the propagation phenomena of ultrasonic waves in prototypes cylindrically shaped implants and to investigate the sensitivity of their ultrasonic response to the surrounding bone biomechanical properties. The 10 MHz ultrasonic response of the implant was calculated using a finite difference numerical simulation tool and was compared to rf signals taken from a recent experimental study by Mathieu et al. [Ultrasound Med. Biol. 37, 262-270 (2011a)]. Reflection and mode conversion phenomena were analyzed to understand the origin of the different echoes and the importance of lateral wave propagation was evidenced. The sensitivity of the ultrasonic response of the implant to changes of (i) amount of bone in contact with the implant, (ii) cortical bone thickness, and (iii) surrounding bone material properties, was compared to the reproducibility of the measurements. The results show that, either a change of 1 mm of bone in contact with the implant, or 1.1 mm of cortical thickness or 12% of trabecular bone mass density should be detectable. This study paves the way for the investigation of the use of quantitative ultrasound techniques for the evaluation of bone-implant interface properties and implant stability.

Micro-Brillouin scattering measurements in mature and newly formed bone tissue surrounding an implant.

The evolution of implant stability in bone tissue remains difficult to assess because remodeling phenomena at the bone-implant interface are still poorly understood. The characterization of the biomechanical properties of newly formed bone tissue in the vicinity of implants at the microscopic scale is of importance in order to better understand the osseointegration process. The objective of this study is to investigate the potentiality of micro-Brillouin scattering techniques to differentiate mature and newly formed bone elastic properties following a multimodality approach using histological analysis. Coin-shaped Ti-6Al-4V implants were placed in vivo at a distance of 200 µm from rabbit tibia leveled cortical bone surface, leading to an initially empty cavity of 200 µm×4.4 mm. After 7 weeks of implantation, the bone samples were removed, fixed, dehydrated, embedded in methyl methacrylate, and sliced into 190 µm thick sections. Ultrasonic velocity measurements were performed using a micro-Brillouin scattering device within regions of interest (ROIs) of 10 µm diameter. The ROIs were located in newly formed bone tissue (within the 200 µm gap) and in mature bone tissue (in the cortical layer of the bone sample). The same section was then stained for histological analysis of the mineral content of the bone sample. The mean values of the ultrasonic velocities were equal to 4.97×10(-3) m/s in newly formed bone tissue and 5.31×10(-3) m/s in mature bone. Analysis of variance (p=2.42×10(-4)) tests revealed significant differences between the two groups of measurements. The standard deviation of the velocities was significantly higher in newly formed bone than in mature bone. Histological observations allow to confirm the accurate locations of the velocity measurements and showed a lower degree of mineralization in newly formed bone than in the mature cortical bone. The higher ultrasonic velocity measured in newly formed bone tissue compared with mature bone might be explained by the higher mineral content in mature bone, which was confirmed by histology. The heterogeneity of biomechanical properties of newly formed bone at the micrometer scale may explain the higher standard deviation of velocity measurements in newly formed bone compared with mature bone. The results demonstrate the feasibility of micro-Brillouin scattering technique to investigate the elastic properties of newly formed bone tissue.

Ultrasonic evaluation of dental implant biomechanical stability: an in vitro study.

Dental implants are widely used for oral rehabilitation. However, there remain risks of failure that are difficult to anticipate. The objective of this ex vivo study is to investigate the potentiality of quantitative ultrasound (QUS) to assess the amount of bone in contact with titanium prototype cylindrical implants. Four groups of 10 rabbit femurs each are considered, corresponding to different amounts of bone in contact with the implant. The 10 MHz ultrasonic response of the implant is processed to derive a quantitative indicator I, based on the temporal variation of the signal amplitude. Analysis of variance (ANOVA) (p < 10(-5)) tests revealed a statistical distribution of I significantly correlated with the amount of bone in contact with the cylinders. An analytical model considering the propagation of lateral waves allows the understanding of the physical origin of the echoes. QUS technique may be used to investigate the amount of bone in contact with a cylinder implant.

Effects of platelet lysates on select bone cell functions.

Although platelet-rich plasma and platelet concentrates have been used to promote bone healing in orthopaedic and maxillofacial surgery, the underlying cellular-level mechanisms remain poorly understood. The present in vitro study investigated the effects of human platelet lysate (PL) on selected functions of cultured bone cells. Cells from 18-day-old fetal rat calvaria were isolated by a collagenase digestion procedure. PL was added at different concentrations on pre- or post-confluent cell stage. After 1 day, bone cell proliferation was maximal and half-maximal in the presence of PL from 3 x 10(8) and 0.5 x 10(8) platelets/ml, respectively. During 17 h, the number of bone cells traversing the scrape border of a scrape wound model increased by 16-fold in the presence of PL from 3 x 10(8) platelets/ml. The presence of PL from 3 x 10(8) platelets/ml in pre-confluent bone cell cultures for 48 h resulted in a threefold decrease of alkaline phosphatase (ALP) specific activity. In the case of confluent bone cells, the presence of PL (from 1 x 10(6) to 3 x 10(8) platelets/ml) for 11 days, the ALP specific activity and total calcium content decreased in a PL dose-dependent manner and reached a minimum in the presence of PL from 3 x 10(8) platelets/ml. In summary, short-term PL exposure (up to 24 h) promotes the proliferative and chemotactic bone cell functions while long-term PL exposure results in a decrease of both ALP activity and mineral formation. These data show that the soluble components contained in PL may affect the bone healing process by modulating differently bone cell functions.

Fibrin sealants and platelet preparations in bone and periodontal healing.

Fibrin sealants and platelet concentrates have been used alone or in association with bone substitutes to promote bone healing in orthopedic and oral surgery. Commercial fibrin sealants are homologous plasma-derived products that mimic the last step of a coagulation cascade, leading to a fibrin clot. They are used for topical hemostasis and tissue sealing and as melting agents for particulate bone substitutes. Infectious risk led to the development of autologous fibrin sealants from the patient's own plasma. However, their fabrication results in less reproducible or less satisfactory rheologic properties. The use of autologous products with high platelet concentrations, such as platelet-rich plasma, platelet concentrate, and platelet gels, has recently been suggested for combining the fibrin sealant properties with the growth factor effects of platelets. We describe the characteristics and limitations of fibrin sealants (commercial/autologous) and platelet preparations and review their effects on bone and periodontal healing as reported in experimental studies and clinical trials.