ABSTRACT
In this work, we initially prepared layered lithium titanate (Li2TiO3) using a solid-state reaction. Then Li+ of Li2TiO3 were acid-eluded with Hydrochloric acid to obtain hydrated titanium oxide (H2TiO3). Different weight percentages (50%, 60%, 70%, 80%, and 90%) of the as-prepared H2TiO3 were deposited on a conductive reduced graphene oxide (rGO) matrix to obtain a series of rGO/ H2TiO3 composites. Of the prepared composites, rGO/H2TiO3-60% showed excellent current density, high specific capacitance, and rapid ion diffusion. An asymmetric MCDI (membrane capacitive deionization) cell fabricated with activated carbon as the anode and rGO/H2TiO3-60% as the cathode displayed outstanding Li+ electrosorption capacity (13.67 mg g-1) with a mean removal rate of 0.40 mg g-1 min-1 in a 10 mM LiCl aqueous solution at 1.8 V. More importantly, the rGO/H2TiO3-60% composite electrode exhibited exceptional Li+ selectivity, superior cyclic stability up to 100,000 s, and a Li+ sorption capacity retention of 96.32% after 50 adsorption/desorption cycles. The excellent Li+ extraction obtained by MCDI using the rGO/H2TiO3-60% negative electrode was putatively attributed to: (i) ion exchange between Li+ and H+ of H2TiO3; (ii) the presence of narrow lattice spaces in H2TiO3 suitable for selective Li+ capture; (iii) capture of Li+ by isolated and hydrogen-bonded hydroxyl groups of H2TiO3; and (iv) enhanced interfacial contact and transfer of large numbers of Li+ ions from the electrolyte to H2TiO3 achieved by compositing H2TiO3 with a highly conductive rGO matrix.
ABSTRACT
In this research, we demonstrated that a crosslinked hydrophilic carbon electrode with better electrochemical performance than hydrophobic counterparts can easily be produced using room-temperature, quick electron-beam irradiation with a hydrophilic methacryloyl-substituted polyvinyl alcohol (SPVA) binder. The SPVA binder was effectively synthesized by trans-esterification of PVA with glycidyl methacrylate. The hydrophilic carbon electrode cast on a graphite sheet from a slurry of activated carbon (AC) and SPVA was irradiated with an electron beam to form a crosslinked structure. The analytical results in terms of the morphology, solvent resistance, chemical composition, and contact angle revealed that the carbon electrode was completely crosslinked by electron-beam irradiation even at the dose of 100 kGy (irradiation time = 180 s). The new electrode exhibited superior water-wettability due to the hydrophilic functionality of SPVA. Furthermore, the hydrophilic carbon electrode with an AC : SPVA composition of 90 : 10 and an absorbed dose of 200 kGy, exhibited a specific capacitance of 127 F g-1 (67% higher than the hydrophobic poly(vinylidene fluoride) (PVDF)-based counterpart with the same composition). The specific capacitance was further improved to 160 F g-1 with an increase in the AC content. The hydrophilic carbon electrode exhibited noticeably better desalination efficiency than the hydrophobic PVDF-based counterpart.
ABSTRACT
Ultrafine oxidized cellulose (OC) mats were prepared by oxidation of ultrafine cellulose mats produced by electrospinning and subsequent deacetylation of cellulose acetate for potential applications in nonwoven adhesion barriers. When ultrafine cellulose mats were oxidized with a mixture of HNO3/H3PO4 - NaNO2 (2/1/1.4 v/v/wt %), their ultrafine mat structure remained unchanged. The yield and carboxyl content of OC mats were 86.7% and 16.8%, respectively. OC showed lower crystallinity than cellulose because the oxidation of cellulose proceeded via disruption of hydrogen bonds between cellulose chains. The swelling behaviors of ultrafine OC mats were dependent on the type of swelling solution. In a physiological salt solution, their degree of swelling was approximately 230%.
