Laser-patterned paper-based flow-through filters and lateral flow immunoassays to enable the detection of C-reactive protein.

We report the use of a laser-based fabrication process in the creation of paper-based flow-through filters that when combined with a traditional lateral flow immunoassay provide an alternative pathway for the detection of a pre-determined analyte over a wide concentration range. The laser-patterned approach was used to create polymeric structures that alter the porosity of the paper to produce porous flow-through filters, with controllable levels of porosity. When located on the top of the front end of a lateral flow immunoassay the flow-through filters were shown to block particles (of known sizes of 200 nm, 500 nm, 1000 nm and 3000 nm) that exceed the effective pore size of the filter while allowing smaller particles to flow through onto a lateral flow immunoassay. The analyte detection is based on the use of a size-exclusive filter that retains a complex (∼3 µm in size) formed by the binding of the target analyte with two antibodies each of which is tagged with different-sized labels (40 nm Au-nanoparticles and 3 µm latex beads), and which is larger than the effective pore size of the filter. This method was tested for the detection of C-reactive protein in a broad concentration range from 10 ng/ml to 100,000 ng/ml with a limit-of-detection found at 13 ng/ml and unlike other reported methods used for analyte detection, with this technique we are able to counter the Hook effect which is a limiting factor in many lateral flow immunoassays.

Laser direct-write for fabrication of three-dimensional paper-based devices.

We report the use of a laser-based direct-write (LDW) technique that allows the design and fabrication of three-dimensional (3D) structures within a paper substrate that enables implementation of multi-step analytical assays via a 3D protocol. The technique is based on laser-induced photo-polymerisation, and through adjustment of the laser writing parameters such as the laser power and scan speed we can control the depths of hydrophobic barriers that are formed within a substrate which, when carefully designed and integrated, produce 3D flow paths. So far, we have successfully used this depth-variable patterning protocol for stacking and sealing of multi-layer substrates, for assembly of backing layers for two-dimensional (2D) lateral flow devices and finally for fabrication of 3D devices. Since the 3D flow paths can also be formed via a single laser-writing process by controlling the patterning parameters, this is a distinct improvement over other methods that require multiple complicated and repetitive assembly procedures. This technique is therefore suitable for cheap, rapid and large-scale fabrication of 3D paper-based microfluidic devices.

Large mode area multi-trench fiber for UV and visible transmission.

We experimentally demonstrate all-solid 10 and 20 µm core diameter multi-trench fibers for UV and visible wavelengths. Measurements ensure an effective single-mode operation over a wide range of bend radii, which is suitable for applications such as beam delivery. Both fibers were fabricated by the conventional modified chemical vapor deposition process, which is suitable for mass production. Moreover, all-solid fiber design ensures easy cleaving and splicing.

Engineering fluidic delays in paper-based devices using laser direct-writing.

We report the use of a new laser-based direct-write technique that allows programmable and timed fluid delivery in channels within a paper substrate which enables implementation of multi-step analytical assays. The technique is based on laser-induced photo-polymerisation, and through adjustment of the laser writing parameters such as the laser power and scan speed we can control the depth and/or the porosity of hydrophobic barriers which, when fabricated in the fluid path, produce controllable fluid delay. We have patterned these flow delaying barriers at pre-defined locations in the fluidic channels using either a continuous wave laser at 405 nm, or a pulsed laser operating at 266 nm. Using this delay patterning protocol we generated flow delays spanning from a few minutes to over half an hour. Since the channels and flow delay barriers can be written via a common laser-writing process, this is a distinct improvement over other methods that require specialist operating environments, or custom-designed equipment. This technique can therefore be used for rapid fabrication of paper-based microfluidic devices that can perform single or multistep analytical assays.

Laser-induced photo-polymerisation for creation of paper-based fluidic devices.

Paper-based microfluidics is a rapidly progressing inter-disciplinary technology driven by the need for low-cost alternatives to conventional point-of-care diagnostic tools. For transport of reagents/analytes, such devices often consist of interconnected hydrophilic fluid-flow channels that are demarcated by hydrophobic barrier walls that extend through the thickness of the paper. Here, we present a laser-based fabrication procedure that uses polymerisation of a photopolymer to produce the required fluidic channels in paper. Experimental results showed that the structures successfully guide the flow of fluids and allow containment of fluids in wells, and hence the technique is suitable for fabrication of paper-based microfluidic devices. The minimum width for the hydrophobic barriers that successfully prevented fluid leakage was ~120 µm and the minimum width for the fluidic channels that can be formed was ~80 µm, the smallest reported so far for paper-based fluidic patterns.

Laser-Induced Forward Transfer-printing of focused ion beam pre-machined crystalline magneto-optic yttrium iron garnet micro-discs.

We present femtosecond laser-induced forward transfer of focused ion beam pre-machined discs of crystalline magneto-optic yttrium iron garnet (YIG) films. Debris-free circular micro-discs with smooth edges and surface uniformity have been successfully printed. The crystalline nature of the printed micro-discs has not been altered by the LIFT printing process, as was confirmed via micro-Raman measurements.

Waveguide mode filters fabricated using laser-induced forward transfer.

Titanium (Ti)-in-diffused lithium niobate waveguide mode filters fabricated using laser-induced forward transfer followed by thermal diffusion are presented. The mode control was achieved by adjusting the separation between adjacent Ti segments thus varying the average value of the refractive index along the length of the in-diffused channel waveguides. The fabrication details, loss measurements and near-field optical characterization of the mode filters are presented. Modeling results regarding the device performance are also discussed.

Spectral and electro-optic response of UV-written waveguides in LiNbO3 single crystals.

An experimental study of the spectral and electro-optic response of direct UV-written waveguides in LiNbO3 is reported. The waveguides were written using c.w. laser radiation at 275, 300.3, 302, and 305 nm wavelengths with various writing powers (35-60 mW) and scan speeds (0.1-1.0 mm/sec). Spectral analysis was used to determine the multimode and single mode wavelength regions and, the cut-off point of the fabricated waveguides. Electro-optic characterization of these waveguides reveals that the electro-optic coefficient (r33) decreases for longer writing wavelengths, with a maximum of 31 pm/V for 275 nm and, is reduced to 14 pm/V for waveguides written with 305 nm.

Latent light-assisted poling of LiNbO3.

The observation of latent light-assisted poling (LAP) in lithium niobate single crystals is reported. More specifically, the nucleation field is reduced and remains reduced for an extended time period (up to several hours) after irradiation with ultrafast (approximately 150 fs) laser light at a wavelength of 400 nm. The maximum nucleation field reduction measured using latent-LAP (62%) was significantly higher in comparison with regular non-time-delayed LAP (41%) under identical irradiation conditions in undoped congruent lithium niobate crystals. No latent-LAP effect was observed in MgO-doped crystals for the experimental conditions used, despite the strong effect observed using regular LAP. The latent-LAP effect is attributed to the formation of a slowly decaying photo-induced space-charge distribution which assists local ferroelectric domain nucleation. The dynamics of latent-LAP are compared with the dynamics of photorefractive grating decay, recorded in lithium niobate crystals of different doping, confirming the space charge hypothesis.

Direct-writing of inverted domains in lithium niobate using a continuous wave ultra violet laser.

The inversion of ferroelectric domains in lithium niobate by a scanning focused ultra-violet laser beam (lambda = 244 nm) is demonstrated. The resulting domain patterns are interrogated using piezoresponse force microscopy and by chemical etching in hydrofluoric acid. Direct ultra-violet laser poling was observed in un-doped congruent, iron doped congruent and titanium in-diffused congruent lithium niobate single crystals. A model is proposed to explain the mechanism of domain inversion.

Photodarkening in Yb-doped aluminosilicate fibers induced by 488 nm irradiation.

Photodarkening of Yb-doped aluminosilicate fibers by continuous wave 488 nm irradiation was investigated. The irradiation induced significant excess loss in the UV-visible spectroscopy (VIS) region in Yb-doped aluminosilicate fibers while pure aluminosilicate fibers showed negligible induced loss. Ultraviolet-VIS-near-infrared spectroscopy revealed an absorption peak at 220 nm in unexposed Yb-doped aluminosilicate fiber preforms. The observed peak was attributed to Yb-associated oxygen deficiency centers (ODCs) and proposed as a precursor of the photodarkening. The proposed model was supported by measurements on oxygen-loaded Yb-doped aluminosilicate fibers. In these, the photodarkening could be significantly reduced, which we attribute to a smaller number of ODCs following oxygen loading.