ABSTRACT
The study presented in this paper investigates the application of asphalt bitumen modification using a fast-reacting SBS polymer at a low modifier percentage. The hypothesis is that a fast-reacting styrene-butadiene-styrene (SBS) polymer that composes only 2% to 3% of the weight of the bitumen modification could extend the life of the pavement surfacing and pavement performance at relatively low input costs, increasing the net present value produced by the pavement during its life cycle. To confirm or refute this hypothesis, two types of road bitumens CA 35/50 and 50/70 were modified with low amounts of fast-reacting SBS polymer with the expectation of attaining properties similar to a 10/40-65 modified bitumen. For each type of unmodified bitumen, bitumen modification and comparative 10/40-65 modified bitumen, the following tests were conducted: needle penetration, softening point-ring and ball test method, and ductility test. The second part of the article focuses on a comparison of asphalt mixtures with different compositions of coarse-grain curves. For each mixture, complex modulus with varying temperatures and fatigue resistances are represented by the Wöhler diagram and compared. Based on in labo testing, the impact of the modification on pavement performance is evaluated. Life cycle changes for each type of modified and unmodified mixtures are quantified as road user costs, and attained benefits are compared with increased construction costs.
ABSTRACT
The utilization of recycled materials is an important issue in the context of environmental protection. The large amounts of recycled material recovered from the demolition of asphalt road structures indicate the need to find new ways of utilizing them. In the case of road renovation projects, large amounts of recycled materials are, in most cases, recovered in the form of reclaimed asphalt pavement (RAP), reclaimed concrete (RC) and recycled aggregate (RA). To focus on the effects of the use of recovered materials (RAP, RC and RA), the same composition was used for all of the analyzed mixtures in terms of foamed bitumen (FB) and Portland cement (CEM) content. The scope of laboratory tests included the specification of the following parameters: the amount of air void content Vm, the determination of axial compression strength at +25 °C, indirect tensile strength (ITS) at +25 °C, water resistance, TSR, water and frost resistance, WRW+M stiffness modulus (IT-CY) at 13 °C, dynamic dynamicmodulus. The plan of the experiment assumed addition recycled material in quantities between 20% and 80% in increments of 20%. The obtained results indicate that both the type and quantity of recycled material significantly affect the properties of the cold-recycled mixture with foamed bitumen. Using reclaimed asphalt pavement and recycled cement concrete guarantees high levels of stiffness in the recycled mixture. Howeverin the case of recycled aggregate, the authors did not observe any visible changes in the dynamicdynamic modulus, irrespective of the loading conditions. It was also indicated that it is necessary to reduce the quantity of reclaimed asphalt pavement in the composition of the FB-RCM mix to maintain the required air void content.
ABSTRACT
Waste plastomer disposal is currently a major challenge facing modern economies. This article reports on a study and analysis regarding the implementation of plastomers into bitumen, with a special focus on the influence of mixing process factors. Two plastomers were selected for analysis, PP and PET, and two bitumen types, 20/30 and 70/100, were modified. Determination of the basic characteristics, such as penetration, softening temperature, cohesion energy, and Fraass temperature, was complemented with advanced multiple-stress creep recovery (MSCR) rheological testing. The entire experimental process followed the Plackett−Burman design. Rheological effects of modified bitumen were evaluated using the generalized Maxwell model. Microstructural analysis with epi-fluorescence microscopy showed the ability of plastomer-modified bitumen to obtain a fine-grained structure with a particle size of <10 µm. In addition, creep susceptibility (Jnr) was found to be statistically significantly dependent on the polymer type and particle size, rotational speed, and bitumen type. In turn, the particle dispersion structure in the bitumen matrix significantly depended on the rotational speed, plastomer particle size, and mixing temperature. Ultimately, the process of bitumen 70/100 modification was optimized. It was demonstrated, following the experimental design, that by using fine-grained PP for a temperature of 160 °C, rotational speed of about 6300 rpm and time of 105 min, it is possible to obtain modified bitumen with rheological properties very similar to those of modified bitumen PmB 45/80-55.
ABSTRACT
In the present study, credible analytical and numerical models are developed in order to explain the apparent discrepancies in the ratios of static and dynamic deformation models for assessing the quality of mechanical efficiency of transport structures in Central Europe. Through of experience, authors specifically deal with the comparison of two commonly used methods: the dynamic load plate test, known as the lightweight dynamic test and the static plate load test. This paper presents the relevant correlation dependency of the most commonly used quantification characteristics in earthworks quality control. Their correlation was obtained by applying the static theory of impact to earthworks quality control, which allows for the application of several quality control methods, in line with other member states of the European Union, specifically with regard to constructions under various boundary conditions (climate, soil moisture of the specified layer). According to an analysis of the results of comparisons of static and dynamic load tests, analytical and numerical models of the subsoil formed by soils and uncemented structural materials, respectively, the linear calculation usually used in the conditions of Central Europe does not have universal validity. Rather than relying on the analytical and FEM models for the soil, the authors have determined that the above dependence is a power dependence.
