ABSTRACT
Here, we present a protocol for a miniaturized microfluidic device that enables quantitative tracking of bacterial growth. We describe steps for fabricating a screen-printed electrode, a laser-induced graphene heater, and a microfluidic device with its integrations. We then detail the electrochemical detection of bacteria using a microfluidic fuel cell. The laser-induced graphene heater provides the temperature for the bacterial culture, and metabolic activity is recognized using a bacterial fuel cell. Please see Srikanth et al.1 for comprehensive information on the application and execution of this protocol.
ABSTRACT
A simple, cost-effective and miniaturized lab-on-a-chip platform has been developed amenable to perform simultaneous cultivation and detection of bacteria. A microfluidic chamber was integrated to screen-printed electrodes for electrochemical detection of bacteria. The temperature required for the bacterial culture was provided through the optimized laser-induced graphene heaters. The concentration of bacteria was quantified accurately with the three-electrode system in the range of 2 × 104 to 1.1 × 109 CFU/mL without any need of biological modifications to the electrodes. The viability of cultured bacteria in the microfluidic device was also confirmed through fluorescent imaging. Furthermore, the metabolic activity of the cultured bacteria was validated through a miniaturized microbial fuel cell. Furthermore, the specificity of electrodes was also performed through electrochemical technique. Finally, a handheld and portable lab-on-a-chip platform was realized by 3D packaging, integrated with a portable potentiostat for real-time and on-field applications.
ABSTRACT
This paper reports on single step and rapid fabrication of interdigitated electrodes (IDEs) using an inkjet printing-based approach. A commercial inkjet-printed circuit board (PCB) printer was used to fabricate the IDEs on a glass substrate. The inkjet printer was optimized for printing IDEs on a glass substrate using a carbon ink with a specified viscosity. Electrochemical impedance spectroscopy in the frequency range of 1 Hz to 1 MHz was employed for chemical sensing applications using an electrochemical workstation. The IDE sensors demonstrated good nitrite quantification abilities, detecting a low concentration of 1 ppm. Taste simulating chemicals were used to experimentally analyze the ability of the developed sensor to detect and quantify tastes as perceived by humans. The performance of the inkjet-printed IDE sensor was compared with that of the IDEs fabricated using maskless direct laser writing (DLW)-based photolithography. The DLW-photolithography-based fabrication approach produces IDE sensors with excellent geometric tolerances and better sensing performance. However, inkjet printing provides IDE sensors at a fraction of the cost and time. The inkjet printing-based IDE sensor, fabricated in under 2 min and costing less than USD 0.3, can be adapted as a suitable IDE sensor with rapid and scalable fabrication process capabilities.
ABSTRACT
The efficacy of droplet-based microfluidic assays depends on droplet size, pattern, generation rate, etc. The size of the droplet is affected by numerous variables as flow rate ratio, viscosity ratio, microchannel geometry, surfactants, nature of fluids and other dimensionless numbers. This work reports rigorous analysis and optimization of the behavior of droplets with change in flow rate ratio and viscosity ratio in a flow-focusing device. Droplets were produced for different flow rate ratios maintaining a constant aqueous phase and varying the continuous phase, to have capillary numbers ranging from 0.01 to 0.1. It was observed that the droplet size decreased with the increase in flow rate ratio, and vice versa. It was noted that as the viscosity ratio was increased, the dispersed phase elongated before the complete breakup and long droplets were formed in the microchannel. Smaller droplets were formed for lower viscosity ratios with a combination of higher flow rate ratios. An empirical relation has been developed to predict the droplet length in terms of capillary number and flow rate ratio for different viscosity ratios. In addition, microparticle encapsulation in individual droplets was attempted to realize the effect of flow rate of the continuous phase for various flow rate ratios on encapsulation efficiency.
ABSTRACT
Controlled, stable and uniform temperature environment with quick response are crucial needs for many lab-on-chip (LOC) applications requiring thermal management. Laser Induced Graphene (LIG) heater is one such mechanism capable of maintaining a wide range of steady state temperature. LIG heaters are thin, flexible, and inexpensive and can be fabricated easily in different geometric configurations. In this perspective, herein, the electro-thermal performance of the LIG heater has been examined for different laser power values and scanning speeds. The experimented laser ablated patterns exhibited varying electrical conductivity corresponding to different combinations of power and speed of the laser. The conductivity of the pattern can be tailored by tuning the parameters which exhibit, a wide range of temperatures making them suitable for diverse lab-on-chip applications. A maximum temperature of 589 °C was observed for a combination of 15% laser power and 5.5% scanning speed. A LOC platform was realized by integrating the developed LIG heaters with a droplet-based microfluidic device. The performance of this LOC platform was analyzed for effective use of LIG heaters to synthesize Gold nanoparticles (GNP). Finally, the functionality of the synthesized GNPs was validated by utilizing them as catalyst in enzymatic glucose biofuel cell and in electrochemical applications.
