Negative Differential Resistance Device from Organic/Inorganic Hybrid Nanostructures.

Negative differential resistance device (NDR) fabricated by spin coating of organic/inorganic hybrid nanostructures at room temperature, is reported in the present paper. The coated organic layer is MEH-PPV (poly-[2-methoxy-5-(2'-ethyl-hexyloxy)-1,4-phenylenevinylene] and inorganic layer is ZnO nanoparticles. The device shows negative differential resistance at low voltage and I­V characteristics of the device show multiple peaks at low voltage values. A value of 13 and 4 for the peak- to-valley ratio of current are reported in bi-layer and single layer structures respectively. Depending on the observed NDR signature, operating mechanisms are explored based on carrier (resonant) tunneling process and donor like trap mechanisms. This results show that the MEH-PPV/ZnO thin films gives good performance and is relevant for applications in optoelectronic devices such as a negative differential resistance.

Enhanced removal of Cr(VI) from aqueous solution using polypyrrole/Fe3O4 magnetic nanocomposite.

Fe(3)O(4) coated polypyrrole (PPy) magnetic nanocomposite was prepared via in situ polymerization of pyrrole monomer for the removal of highly toxic Cr(VI). Structure and morphology of the prepared nanocomposite were characterized by attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), X-ray diffraction pattern, Field emission scanning electron microscopy (FE-SEM) and high resolution transmission electron microscopy (HR-TEM). Electron spin resonance (ESR) studies confirmed that the nanocomposite is magnetic in nature. Up to 100% adsorption was found with 200mg/L Cr(VI) aqueous solution at pH 2. Adsorption of Cr(VI) on the surface of the adsorbent was confirmed by the ATR-FTIR and X-ray photoelectron spectroscopy (XPS). XPS studies also suggested that ion exchange and reduction on the surface of the nanocomposite may be the possible mechanism for Cr(VI) removal by the PPy/Fe(3)O(4) nanocomposite. Adsorption results showed that Cr(VI) removal efficiency by the nanocomposite decreased with an increase in pH. Adsorption kinetics was best described by the pseudo-second-order rate model. Isotherm data fitted well to the Langmuir isotherm model. Thermodynamic study revealed that the adsorption process is endothermic and spontaneous in nature. Desorption experiment showed that in spite of the very poor recovery of the adsorbed Cr(VI); the regenerated adsorbent can be reused successfully for two successive adsorption-desorption cycles without appreciable loss of its original capacity.

Removal of fluoride from aqueous solution by polypyrrole/Fe3O4 magnetic nanocomposite.

Polypyrrole (PPy)/Fe(3)O(4) magnetic nanocomposite as a novel adsorbent was prepared via in-situ polymerization of pyrrole (Py) monomer using FeCl(3) oxidant in aqueous medium in which Fe(3)O(4) nanoparticles were suspended. The adsorbent was characterized by Attenuated Total Reflectance Fourier transform infrared spectroscope (ATR-FTIR), Brunauer-Emmet-Teller (BET) method, field emission scanning electron microscope (FE-SEM), high resolution transmission electron microscope (HR-TEM), X-ray photoelectron spectroscope (XPS) and X-ray diffraction (XRD). Magnetic property of the adsorbent was measured by electron spin resonance (ESR). Subsequently, the ability of the adsorbent to remove fluoride ions from aqueous solution was demonstrated in a batch sorption mode. Results reveal that the adsorption is rapid and that the adsorbent has high affinity for fluoride, which depends on temperature, solution pH and adsorbent dose. From equilibrium modelling, the equilibrium data is well described by Freundlich and Langmuir-Freundlich isotherms while the adsorption kinetics is described by the pseudo-second-order model. Thermodynamic parameters confirm the spontaneity and endothermic nature of the fluoride adsorption. Meanwhile, the fluoride adsorption proceeds by an ion exchange mechanism.

AFM nano-plough planar YBCO micro-bridges: critical currents and magnetic field effects.

The critical current (Ic) of YBa2Cu3O7-x (YBCO) AFM plough micro-constrictions is measured as a function of temperature, width and the magnetic flux density (B), which was applied perpendicular to the YBCO ab-plane and surface of the bridges. C-axis oriented thin films of YBa2Cu3O7-x were deposited on MgO substrates using an inverted cylindrical magnetron (ICM) sputtering technique. The films were then patterned into 8-10 micron size strips, using standard photolithography and dry etching processes. Micro-bridges with widths between 1.9 microm to 4.1 microm were fabricated by using atomic force microscope (AFM) nanolithography techniques. Critical current versus temperature data shows a straight-line behavior, which is typical of constriction type Josephson junctions. The Ic versus B characteristics exhibited a modulation, and a suppression of the critical current of up to 84%. It was also found that the critical current increases with increasing constriction width.

Magnetic characterization of radio frequency heat affected micron size Fe3O4 powders: a bio-application perspective.

Micron size Fe3O4 powders were chemically prepared and processed by radio frequency (13.56 MHz) oxygen plasma irradiation technique at different elevated temperatures using low radio frequency (RF) power level. Low magnetic field RF superconducting quantum interference device (SQUID) magnetization studies were performed up to a maximum magnetic field of 100 Oe, which was well below the magnetic field tolerance factor of human beings and at different temperatures (down to 5 K). Heat-treated powders in RF oxygen plasma showed significant changes in blocking temperature, magnetization and susceptibility, which are important parameters for bio-applications. It is observed that blocking temperature is decreased under identical RF heat treatment in oxygen plasma and noted to be dependent on average particle size. Microscopic rise in electron temperature during RF heating may likely to enhance the electron-hopping rate between Fe(+2) and Fe(+3) in the octahedral site of Fe3O4 molecular crystal structure, which in turn exhibit changes in blocking temperature including low field magnetization and susceptibility. These properties of Fe3O4 fine powder are likely to play important role in generating and processing biocompatible Ferro-fluid down to nanoscopic size for biomaterials applications.

Nanoplough-constrictions on thin YBCO films made with atomic force microscopy.

Utilizing atomic force microscope (AFM) with a diamond tip, we were able to successfully plough nano-constrictions on epitaxially grown YBa2Cu3O(7-x) thin films deposited on MgO substrates. The thickness, width, and length of the obtained constrictions were in the range of a few 100 nm. Furthermore, we managed to produce a new S-type constriction, of which the dimensions are easier to control than for conventional constrictions.