Influence of Hybrid Surface Modification on Biocompatibility and Physicochemical Properties of Ti-6Al-4V ELI Titanium.

Titanium-based materials are the most widely used materials in biomedical applications. However, according to literature findings, the degradation products of titanium have been associated with potential allergic reactions, inflammation, and bone resorption. The corrosion process of Ti-6Al-4V in the human body environment may be exacerbated by factors such as reduced pH levels and elevated concentrations of chloride compounds. Coatings made of biopolymers are gaining attention as they offer numerous advantages for enhancing implant functionality, including improved biocompatibility, bioactivity, wettability, drug release, and antibacterial activity. This study analyzes the physicochemical and electrochemical behavior of the Ti-6Al-4V ELI alloy subjected to PCL and PCL/TiO2 deposition by the electrospinning method. To characterize the polymer-based layer, tests of chemical and phase composition, as well as surface morphology investigations, were performed. Wetting angle tests were conducted as part of assessing the physicochemical properties. The samples were subjected to corrosion behavior analysis, which included open circuit potential measurements, potentiodynamic tests, and the electrochemical impedance spectroscopy method. Additionally, the quantification of released ions post the potentiodynamic test was carried out using the inductively coupled plasma atomic emission spectrometry (ICP-AES) method. Cytotoxicity tests were also performed. It was found that surface modification by depositing a polymer-based layer on the titanium substrate material using the electrospinning method provides improved corrosion behavior, and the samples exhibit non-toxic properties.

Study of the Impact of Coals and Claystones on Wear-Resistant Steels.

This paper discusses the impact of coal abrasive materials of varied petrographic composition and claystones containing admixtures of coal matter on the surface wear of wear-resistant martensitic steels. Wear tests were conducted at a test stand for three petrographic varieties of hard coal: vitrinite, clarinite, and durinite, and five samples of claystone. These tests revealed no significant effect of the type of coal abrasive used on the value of mass loss from the surface of the wear-resistant steel samples. The reason behind the foregoing is the observed tendency of coal abrasives, irrespective of their petrographic variety, to penetrate surface irregularities, especially those attributable to previous surface treatment of the samples and the impact of wear products. The dominant forms of surface damage were surface fatigue chipping and scratches caused by the particles which detached themselves from the surface of the steel samples, as observed for all the analysed coal variants. On the surfaces of the samples seasoned in the presence of claystones, highly varied forms of damage were observed: microcutting, scaly surface cracks, delamination, and deep cracks. In these cases, it was possible that the abrasive grains had been pressed into the steel surface irregularities, but no layered forms of the pressed-in abrasive material were observed to have developed. The paper also presents a model for the formation of coal films and discusses their possible effect on wear minimisation.

Investigation of Ti/Al2O3 + TiO2 and Ti + TiO2/Al2O3 + TiO2 hybrid coatings as protection of ultra-light Mg-(Li)-Al-RE alloys against corrosion.

Low corrosion resistance is a significant problem of magnesium alloys, particularly ultra-light magnesium-lithium alloys. Surface treatment is one way to improve their corrosion resistance. The paper presents the results of tests of Ti/Al2O3 + TiO2 and Ti + TiO2/Al2O3 + TiO2 coatings obtained in a hybrid process combining PVD and ALD methods and ALD coating of Al2O3 + TiO2 type obtained on AE42 (Mg-4Li-2RE) and LAE442 (Mg-4Li-4Al-2RE). Structural studies were performed using scanning and transmission electron microscopy (SEM and TEM), atomic force microscopy and EDS and XPS spectroscopic methods. Potentiodynamic tests and electrochemical impedance spectroscopy EIS in 0.05 M NaCl solution were performed to determine the electrochemical properties of the tested materials. Moreover, tests of surface wettability and tribological properties using the ball-on-disc method were performed. Based on the analysis of anodic polarisation curves and Tafel analysis, it was found that the Ti + TiO2/Al2O3 + TiO2 coating showed the best potentiodynamic properties on both substrates. In particular, on the magnesium-lithium substrate, the value of the polarisation resistance of this hybrid coating is Rpol = 14 × 103 Ω × cm2, and the value of the corrosion current is jcorr = 0.4 µA/cm2. For the uncoated LAE442 substrate, the polarisation resistance is Rpol = 1.05 × 103 Ω × cm2, and the corrosion current value is jcorr = 5.49 µA/cm2. This improvement is due to the synergistic effect of the combined PVD and ALD technologies. The study confirmed the impact of hybrid coatings on improving the anti-corrosion and tribological properties of ultra-light magnesium alloys.

Structure and Properties of TiO2/nanoTiO2 Bimodal Coatings Obtained by a Hybrid PVD/ALD Method on 316L Steel Substrate.

This paper presents the synergy of the effect of two surface engineering technologies-magnetron sputtering (MS-PVD) and atomic layer deposition (ALD) on the structure and properties of 316L steel. Recent studies indicate that PVD coatings, despite their thickness of a few micrometers, have many discontinuities and structural defects, which may lead to pitting corrosion after time. Applying an ALD layer to a PVD coating seals its structure and contributes to extending the service life of the coating. Investigations of the structure and morphology of the produced layers were carried out using a scanning electron microscope (SEM) and atomic force microscope (AFM). In addition, the structure of the coatings was investigated on the cross-section using a scanning-transmission electron microscope S/TEM. The tribological properties of the materials studied were determined by the ball-on-disc method. The corrosion resistance of the tested materials was determined by the electrochemical potentiodynamic method by recording the polarization curves of the anodes. Additional information about the electrochemical properties of the tested samples, including the quality, their tightness, and their resistivity, was obtained by electrochemical impedance spectroscopy (EIS). In addition, the main mechanisms of corrosion and tribological wear were determined by SEM observations after corrosion tests and after tribological tests. The study showed that the fabrication of hybrid layers by MS-PVD and ALD techniques allows obtaining coatings with electrochemical properties superior to those of layers fabricated by only one method.

Impact of Surface Treatment on the Functional Properties Stainless Steel for Biomedical Applications.

The main goal of the carried out tests was to analyze the influence of the surface modification of a substrate by depositing composite ZnO layers by the Atomic Layer Deposition (ALD) method. The samples were subjected to preliminary surface modification consisting of being sandblasted and electropolished. A ZnO layer was applied to the prepared substrates by the ALD method. As a precursor of ZnO, diethylzinc (DEZ) was used, which reacted with water, enabling the deposition of the thin films. The chamber temperature was as follows: T = 100-300 °C. The number of cycles was 500 and 1500. As part of the assessment of the physicochemical properties of the resulting surface layers, the tests of chemical composition of the layer, pitting corrosion, impedance corrosion, adhesion to the metal substrate, morphology surface, and wettability were carried out. On the basis of the obtained research, it was found that a composite ZnO layer deposited onto a substrate previously subjected to the electrochemical polishing process has more favorable physicochemical properties. Moreover, an influence of temperature and the number of cycles of the deposition process on the obtained properties was observed, where the ZnO layer was characterized by more favorable properties at a temperature of 200-300 °C at 1500 cycles of the deposition process.

Structure and Properties of ZnO Coatings Obtained by Atomic Layer Deposition (ALD) Method on a Cr-Ni-Mo Steel Substrate Type.

This paper aimed to investigate the structure and physicochemical and tribological properties of ZnO coatings deposited by ALD on 316L stainless steel for biomedical applications. To obtain ZnO films, diethylzinc (DEZ) and water were used as ALD precursors. Zinc oxide layers were deposited at the same temperature of 200 °C using three types of ALD cycles: 500, 1000 and 1500. The structure and morphology of ZnO coatings were examined using SEM and AFM microscopes. The XRD and GIXRD methods were used for the phase analysis of the obtained coatings. To determine the resistance to pitting corrosion, potentiodynamic investigations and impedance spectroscopy were conducted in a Ringer solution at a temperature of 37 °C. The obtained results showed that the number of ALD cycles had a significant impact on the structure, morphology and corrosion resistance of the ZnO layers. It was found that after increasing the coating thickness of the ZnO on the material, its electrochemical properties determining the corrosion resistance also increased. Moreover, on the basis of the ball-on-plate tribological investigations, we found a significant reduction in the friction coefficient of the samples with the investigated coatings in relation to the noncoated substrates.

Analysis of Plastic Deformation Instabilities at Elevated Temperatures in Hot-Rolled Medium-Mn Steel.

The study addressed the microstructure and mechanical properties of hot-rolled advanced high-strength medium manganese steel. Some of the curves that were obtained in static tensile tests at deformation temperatures of 20-200°C showed the occurrence of the heterogeneous plastic deformation phenomenon, called the Portevin-Le Chatelier (PLC) effect. The deformation temperature significantly influenced a serration character. The correlations between the deformation temperature, serration range, microstructural features, and fracture behavior were investigated. The curves showed no Lüders elongation as a result of the thermomechanical processing applied. The serrated flow phenomenon was observed at 60 and 140 °C. The serration type was different and the most enhanced at 140 °C, where the PLC effect was present in both uniform and post-uniform elongation ranges. The disappearance of serrations at 200 °C was related to the increased diffusion intensity.

Laser Micro-Texturing of Sintered Tool Materials Surface.

The purpose of this paper is to show the effect of tool materials surface treatment while using laser texturing on the structure and properties of cemented carbides and sialon ceramics. The tests were made on multi-point inserts subjected laser texturization and honeycomb-like texture was obtained. Comprehensive investigations in the scanning electron microscope (SEM) were made. Morphology was examined by the use of atomic forces microscope (AFM) and confocal microscope. The chemical composition of the tested materials using energy-dispersive X-ray spectrometer (EDS) was investigated. Moreover, exploitative properties, including wear resistance using the "pin on disc" method and roughness, were also tested. It was found that the laser texturing provides a suitable modification of the structure improving tribological properties. Tests suggest that laser texturing can contribute to the durability of cutting tool's edge, which qualifies this type of surface treatment for wide industrial applications.