Determination of trace elements in lithium niobate crystals by solid sampling and solution-based spectrometry methods.

Solid sampling (SS) graphite furnace atomic absorption spectrometry (GFAAS) and solution-based (SB) methods of GFAAS, flame atomic absorption spectrometry (FAAS), inductively coupled plasma optical emission spectrometry (ICP-OES) and inductively coupled plasma mass spectrometry (ICP-MS) were elaborated and/or optimized for the determination of Cr, Fe and Mn trace elements used as dopants in lithium niobate optical crystals. The calibration of the SS-GFAAS analysis was possible with the application of the three-point-estimation standard addition method, while the SB methods were mostly calibrated against matrix-matched and/or acidic standards. Spectral and non-spectral interferences were studied in SB-GFAAS after digestion of the samples. The SS-GFAAS method required the use of less sensitive spectral lines of the analytes and a higher internal furnace gas (Ar) flow rate to decrease the sensitivity for crystal samples of higher (doped) analyte content. The chemical forms of the matrix produced at various stages of the graphite furnace heating cycle, dispensed either as a solid sample or a solution (after digestion), were studied by means of the X-ray near-edge absorption structure (XANES). These results revealed that the solid matrix vaporized/deposited in the graphite furnace is mostly present in the metallic form, while the dry residue from the solution form mostly vaporized/deposited as the oxide of niobium.

Determination of rare-earth elements in uranium-bearing materials by inductively coupled plasma mass spectrometry.

A novel and simple analytical procedure has been developed for the trace-level determination of lanthanides (rare-earth elements) in uranium-bearing materials by inductively coupled plasma sector-field mass spectrometry (ICP-SFMS). The method involves a selective extraction chromatographic separation of lanthanides using TRU resin followed by ICP-SFMS analysis. The limits of detection of the method proposed is in the low pg g(-1) range, which are approximately two orders of magnitude better than that of without chemical separation. The method was validated by the measurement of reference material and applied for the analysis of uranium ore concentrates (yellow cakes) for nuclear forensic purposes, as a potential application of the methodology.

Presence of cancerostatic platinum compounds in hospital wastewater and possible elimination by adsorption to activated sludge.

Platinum originating from the excreted cancerostatic platinum compounds (CPC) cisplatin, carboplatin and oxaliplatin was monitored over a period of 28 days in the wastewater of the oncologic ward of the Vienna University Hospital. Concentration levels ranging from 4.7 to 145 microg L(-1) were measured by inductively coupled plasma mass spectrometry (ICP-MS). An average ratio of weekly drug emission/drug consumption of 0.27+/-0.12 was assessed. Model studies were carried out for fundamental understanding of CPC interaction with the solid phases present at different stages of the water cycle. Wastewater and activated sludge were spiked with CPC at concentration levels as found in the sewer of the oncologic ward. The platinum concentration remaining in the tested solution was measured after 24 h of incubation. Depending on pH, the three substances exhibited considerably different adsorption rates in wastewater. At pH 7, cisplatin was adsorbed by 88%, whereas only 26% of carboplatin and 54% of oxaliplatin were removed from the aqueous phase. Adsorption by activated sludge was higher, less affected by pH variation and comparable for all investigated CPC (96% for cisplatin, 70% for carboplatin and 74% for oxaliplatin at pH 6.8). In a next step, the dependence of CPC adsorption was tested for wastewater and activated sludge of different sampling sites. Strong variations were found only for wastewater, whereas activated sludge showed more consistent elimination rates (average values: cisplatin 92%, carboplatin 72%, and oxaliplatin 78%). These findings indicate that the major part of the excreted CPC is adsorbed by the solid phase in the water cycle and is thus expected to be removed from the wastewater by sewage treatment plants.

Characterisation of a hydraulic high-pressure sample introduction assisted flow injection-inductively coupled plasma time-of-flight mass spectrometry system and its application to the analysis of biological samples.

A flow injection (FI) method was developed using hydraulic high-pressure nebulization as a sample introduction system, coupled to inductively coupled plasma time-of-flight mass spectrometer (ICP-TOFMS) for rapid and simultaneous determination of 19 elements. The operating conditions of the system (analyte flow rate, heating and cooling temperatures of the desolvation module, carrier gas flow rate) for the simultaneous determination of 19 analytes were optimised. The optimum parameters of the sample introduction system were found to be 1.4mlmin(-1) and 1.35lmin(-1) for the analyte solution and nebulizer flow rates, respectively. A compromised condition for heating and cooling stage temperatures of 170 and -5 degrees C was chosen. The detection limits were compared to those obtained by using ICP-TOFMS with alternative sample introduction techniques e.g. conventional nebulization, flow injection chemical hydride generation (FI-CHG) and the obtained results were comparable or better than those resulting from alternative sample introduction. Applying the optimised conditions the simultaneous determination of Ag, As, Ba, Cd, Co, Cu, Ga, In, Li, Mn, Mo, Pb, Sb, Se, Sn, Sr, Tl, V and Zn was carried out. Absolute detection limits (3sigma) in the range of 2-750pg and precision between 0.5 and 9.6% from five replicate measurements of 10ngml(-1) multielemental sample solutions were achieved by using a 200mul sample loop. The developed method was applied for the analysis of certified reference materials of biological origin (TORT-2 "Lobster Hepatopancrease", BCR-422 "Cod Muscle" and IAEA MA-B-3/TM "Fish Homogenate"), and the results showed good agreement with the certified values.

Preparation, homogeneity and stability studies of a candidate LRM for Se speciation.

A laboratory reference material (LRM) was prepared from Brazil nuts (Bertholletia excelsa) for quality control (QC) purposes of selenium speciation. The preparation of this LRM led through the usual operation steps applied during routine reference material production from biota samples-preparation of the raw material, homogenisation, storage design, checking of homogeneity, microbiological status and possible irradiation effects, and monitoring the species stability vs time at different storage temperatures. The selenium speciation studies to check species stability were carried out on a HPLC-UV-HG-AFS measurement set-up. Special attention was paid to the correct identification of selenium species by applying independent HPLC separation techniques (ion-pairing and anion-exchange chromatography). The concentration of selenomethionine (SeMet) and total Se content were quantified (79.9 microg g(-1) (calculated as Se) and 82.9 microg g(-1), respectively). The homogeneity and stability of this candidate reference material passed the relevant tests recommended by Bureau Communautaire de Référence (BCR).