ABSTRACT
Silicon has shown promise for use as a small band gap (1.1 eV) absorber material in photoelectrochemical (PEC) water splitting. However, the limited stability of silicon in acidic electrolyte requires the use of protection strategies coupled with catalysts. Herein, spin coating is used as a versatile method to directly coat silicon photoanodes with an IrOx oxygen evolution reaction (OER) catalyst, reducing the processing complexity compared to conventional fabrication schemes. Biphasic strontium chloride/iridium oxide (SrCl2:IrOx) catalysts are also developed, and both catalysts form photoactive junctions with silicon and demonstrate high photoanode activity. The iridium oxide photoanode displays a photocurrent onset at 1.06 V vs reversible hydrogen electrode (RHE), while the SrCl2:IrOx photoanode onsets earlier at 0.96 V vs RHE. The differing potentials are consistent with the observed photovoltages of 0.43 and 0.53 V for the IrOx and SrCl2:IrOx, respectively. By measuring the oxidation of a reversible redox couple, Fe(CN)63-/4-, we compare the charge carrier extraction of the devices and show that the addition of SrCl2 to the IrOx catalyst improves the silicon-electrolyte interface compared to pure IrOx. However, the durability of the strontium-containing photoanode remains a challenge, with its photocurrent density decreasing by 90% over 4 h. The IrOx photoanode, on the other hand, maintained a stable photocurrent density over this timescale. Characterization of the as-prepared and post-tested material structure via Auger electron spectroscopy identifies catalyst film cracking and delamination as the primary failure modes. We propose that improvements to catalyst adhesion should further the viability of spin coating as a technique for photoanode preparation.
ABSTRACT
Multimetallic Ir-based systems offer significant opportunities for enhanced oxygen evolution electrocatalysis by modifying the electronic and geometric properties of the active catalyst. Herein, a systematic investigation of bimetallic Ir-based thin films was performed to identify activity and stability trends across material systems for the oxygen evolution reaction (OER) in acidic media. Electron beam evaporation was used to co-deposit metallic films of Ir, IrSn2, IrCr, IrTi, and IrNi. The electrocatalytic activity of the electrochemically oxidized alloys was found to increase in the following order: IrTi < IrSn2 < Ir â¼ IrNi < IrCr. The IrCr system demonstrates two times the catalytic activity of Ir at 1.65 V versus RHE. Density functional theory calculations suggest that this enhancement is due to Cr active sites that have improved oxygen binding energetics compared to those of pure Ir oxide. This work identifies IrCr as a promising new catalyst system that facilitates reduced precious metal loadings for acid-based OER catalysis.
ABSTRACT
Improving the performance of oxygen reduction reaction (ORR) electrocatalysts is essential for the commercial efficacy of many renewable energy technologies, including low temperature polymer electrolyte fuel cells (PEFCs). Herein, we report highly active and stable carbon-supported Ru@Pt core-shell nanoparticles (Ru@Pt/C) prepared by a wet chemical synthesis technique. Through rotating disc electrode testing, the Ru@Pt/C achieves an ORR Pt mass-based activity of 0.50 A mgPt-1 at 0.9 V versus the reversible hydrogen electrode (RHE), which exceeds the activity of the state-of-the-art commercial Pt/C catalyst as well as the Department of Energy 2020 PEFC electrocatalyst activity targets for transportation applications. The impact of various synthetic parameters, including Pt to Ru ratios and catalyst pretreatments (i.e., annealing) are thoroughly explored. Pt-based mass activity of all prepared Ru@Pt/C catalysts was found to exceed 0.4 mgPt-1 across the range of compositions investigated, with the maximum activity catalyst having a Ru:Pt ratio of 1:1. This optimized composition of Ru@Pt/C catalyst demonstrated remarkable stability after 30,000 accelerated durability cycles (0.6 to 1.0 V vs. RHE at 125 mV s-1), maintaining 85% of its initial mass activity. Scanning transmission electron microscopy energy dispersive spectroscopy (STEM-EDS) analysis at various stages of electrochemical testing demonstrated that the Pt shell can provide sufficient protection against the dissolution of the otherwise unstable Ru core.
ABSTRACT
Enhanced catalysis for electrochemical oxygen evolution is essential for the efficacy of many renewable energy technologies, including water electrolyzers and metal-air batteries. Recently, Au supports have been shown to enhance the activity of many 3d transition metal-oxide thin films for the oxygen evolution reaction (OER) in alkaline media. Herein, we translate the beneficial impact of Au supports to high surface area, device-ready core-shell nanoparticles consisting of a Au-core and a metal-oxide shell (Au@MxOy where M = Ni, Co, Fe, and CoFe). Through a systematic evaluation, we establish trends in performance and illustrate the universal activity enhancement when employing the Au-core in the 3d transition metal-oxide nanoparticles. The highest activity particles, Au@CoFeOx, demonstrate an overpotential of 328 ± 3 mV over a 2 h stability test at 10 mA cm-2, illustrating that strategically coupling Au support and mixed metal-oxide effects in a core-shell nanoparticle morphology is a promising avenue to achieve device-ready, high-performance OER catalysts.
ABSTRACT
There is a delicate balance between ion exchange capacity (IEC), conductivity, and dimensional stability in anion exchange membranes as higher charge content can lead to increased water uptake, causing excessive swelling and charge dilution. Using highly-charged benzyltrimethylammonium polysulfone (IEC=2.99â mEq g(-1) ) as a benchmark (which ruptured in water even at room temperature), we report the ability to dramatically decrease water uptake using a semi-interpenetrating network wherein we reinforced the linear polyelectrolyte with a crosslinked poly(styrene-co-divinylbenzene) network. These membranes show enhanced dimensional stability as a result of lower water uptake (75 % vs. 301 % at 25 °C) while maintaining excellent hydroxide conductivity (up to 50â mS cm(-1) at 25 °C). These improvements produced an enhanced alkaline fuel cell capable of generating 236â mW cm(-2) peak power density at 80 °C. This method is easily adaptable and can be a viable strategy for stabilizing existing systems.