Advanced micro-extraction techniques (SPME, HiSorb) for the determination of goat cheese whey wastewater VOCs.

HiSorb and solid-phase microextraction (SPME), two environmentally friendly micro-extraction techniques based on the same fundamental principles, were evaluated for their extraction efficiency of volatile organic compounds (VOCs) from goat cheese whey wastewater. For this purpose, a sample preparation method based on the headspace-HiSorb technique was developed and evaluated for its efficiency in terms of the amount of extracted compounds and reproducibility of results. Thermal desorption-gas chromatography/mass spectrometry (TD-GC/MS) and GC/MS analytical methods were used to perform the wastewater analysis, respectively. The experimental parameters of HiSorb were evaluated in terms of probe coating, extraction time, stirring speed, sample volume, extraction temperature and salt addition. Under optimal extraction conditions, it was observed that the use of the divinylbenzene/carbon wide range/polydimethylsiloxane (DVB/CWR/PDMS) triple coating for HiSorb and DVB/Carboxen (CAR)/PDMS for SPME, was best suited to extract a broader range of VOCs with higher peak intensities. A total of 34 VOCs were extracted and determined with the DVB/CWR/PDMS HiSorb probe, while only 23 VOCs were determined with the conventional DVB/CAR/PDMS SPME fiber. The DVB/CWR/PDMS HiSorb probe has a higher adsorbent capacity which results in a higher sensitivity for VOCs compared to the DVB/CAR/PDMS SPME fiber. Furthermore, the HiSorb technique exhibits better reproducibility, as indicated by the lower relative standard deviation (RSD) of 3.7% compared to 7.1% for SPME. Therefore, the HiSorb technique is an effective method for detecting VOCs in complex matrices, such as wastewater.

Assessment of volatile emissions by aging books.

Indoor air quality (IAQ) has attracted a lot of attention due to its complexity and direct effect on human health. Indoor settings in libraries entail various volatile organic compounds (VOCs) linked to the aging and degradation of print material. The effect of the storage environment on paper life expectancy was investigated by targeting the VOC emissions of old and new books using headspace solid phase micro extraction-gas chromatography/mass spectrometry (HS-SPME-GC/MS) analysis. "Sniffing" of book degradation markers showed both ubiquitously and infrequently occurring VOCs. Old book "degradomics" revealed mostly alcohols (57%) and ethers (12%), whereas new books resulted mainly to ketones (40%) and aldehydes (21%). Chemometric processing of the results with principal component analysis (PCA) corroborated our initial observations and was able to discriminate the books by age into three groups: very old books (from the 1600 s to mid-1700), old books (from the 1800s to the early 1900s), and modern books (from the mid-twentieth century onwards) based on their gaseous markers. The measured mean concentrations of selected VOCs (acetic acid, furfural, benzene, and toluene) were below the respective guidelines set for similar places (i.e. museums). The applied non-invasive, green analytical methodology (HS-SPME-GC/MS) can assist librarians, stakeholders, and researchers to evaluate the IAQ, as well as the degree of degradation, and take the appropriate measures for book restoration and monitoring protocols.

Compost-assisted revegetation of highly phytotoxic sulfidic tailings with Medicago sativa L. plants grown from the seed to seedpod stage under greenhouse experimental mesocosms conditions.

The revegetation of highly phytotoxic sulfidic tailings is a challenging task which may often be successfully accomplished only following the addition of soil amendments. This study evaluated the use of green compost at increasing rates (10, 25 and 50% v/v) for the revegetation of extremely acidic sulfidic tailings of the North Mathiatis mine, Cyprus, with the use of alfalfa (Medicago sativa L.) plants, under greenhouse conditions. Alfalfa seeds were successfully germinated in tailings amended either with 25% or 50% (v/v) compost (52 and 85%, respectively). Plants managed to complete their life cycle and produce seeds only in the tailings amended with 50% (v/v) compost, since plants grown in tailings amended with lower rates of compost (i.e., 10 or 25% v/v) showed severe symptoms of phytotoxicity and eventually died. The amendment of tailings with 50% (v/v) green compost resulted in increased pH values, water holding capacity and organic content levels, soil respiration rates, as well as changes in soil elemental composition compared with tailings alone treatment, which in turn facilitated the growth and development of alfalfa plants during the whole experimental period (140 days). Plants managed to reach the late seedpod growth stage, indicating their potential regeneration and continual existence to the amended tailings, simultaneously uncovering the development of favorable conditions in the rhizosphere for the successful revegetation of studied tailings.

N-Source Determines Barley Productivity, Nutrient Accumulation, and Grain Quality in Cyprus Rainfed Agricultural Systems.

The Eastern Mediterranean and Middle East (EMME) region is already experiencing the negative effects of increased temperatures and the increase in prolonged drought periods. The use of organic fertilization could be a valuable tool to meet the main challenges of climate change and maintain the productivity, quality, and sustainability of rainfed agricultural ecosystems. In the current study, we compare the effect of manure, compost, and chemical fertilization (NH4NO3) on barley grain and straw yield in a field study for three consecutive growing seasons. The hypothesis that the barley productivity, nutrient accumulation, and grain quality remain similar among the different nutrient management strategies was tested. The results showed that both growing season and type of nutrient source significantly affected barley grain and straw yield (F6,96 = 13.57, p < 0.01). The lowest productivity was noticed in the non-fertilized plots while chemical and organic fertilization exhibited similar grain yield, ranging from 2 to 3.4 t/ha throughout the growing seasons. For straw, the use of compost had no effect on the yield in any of the growing seasons examined. The use of manure and compost had a significant effect on grain macro- and micronutrient content but this was highly related to growing season. Principal component analysis (PCA) clearly demonstrated the discrimination of the different type of fertilization on barley performance during the course of the study, while the application of compost was highly associated with an increase in micronutrients in grain samples. Furthermore, structural equational modeling (SEM) showed that both chemical and organic fertilization had a direct positive effect on macro- (r = 0.44, p < 0.01) and micronutrient (r = 0.88, p < 0.01) content of barley grain and a positive indirect effect on barley productivity through N accumulation in grain (ß = 0.15, p = 0.007). The current study showed that barley grain and straw yield was similar between manure and NH4NO3 treatments, while compost exhibited a residual positive effect causing an increase in grain yield during the growing season. The results highlight that N fertilization under rainfed conditions is beneficial to barley productivity through its indirect effects on N accumulation in grain and straw, while it improves grain quality through the increased accumulation of micronutrients.

Tomato waste biochar in the framework of circular economy.

Tomato pomace was slowly pyrolyzed at 350 and 550 °C (under an N2 flow of 50 L/h) at a rate of 6 °C/min and a residence time of 1:30 h to produce two biochars named B350 and B550, respectively. In addition, the two biochars were chemically activated with ΚΟΗ (at a ratio of 1:10 w/v) at 800 °C to produce two new materials named BA350 and BA550. The four biochars produced were characterized physically and chemically (pH, yield, calorific value). They were also analyzed by scanning electron microscopy (SEM), Brunauer-Emmett-Teller (B.E.T), elemental analysis (EA), and thermogravimetric analysis (TGA). The results showed that as the pyrolysis temperature increased (350 to 550 °C), the specific surface area (SSA) increased. The latter was also significantly increased by the activation process. EA showed a variation in the mineral content of the produced biochars, resulting in a different content of the biochars after activation. The parameters studied showed that biochars from tomato waste could be used as an organic amendment to improve soil fertility in agricultural. In addition, because of their ability to absorb water, they could be used as a water reservoir in soils in arid areas.

LCA of Barley Production: A Case Study from Cyprus.

Greenhouse gas emissions (i.e., carbon dioxide, methane, nitrous oxide) produced by agriculture contribute to global warming and climate change. Various practices followed by farmers in different environmental conditions contribute to the increase in the phenomena, and there is a need for immediate measures. The current study examines the environmental impact of barley production under rain-fed conditions in Cyprus. For this, four different nutrient management scenarios were investigated in order to evaluate the environmental performance of crop production, namely: (1) Nitrogen (20%), Phosphorous (20%), Potassium (10%); (2) Nitrogen (20%), Phosphorous (20%), Potassium (10%) and manure; (3) Nitrogen (25%), Phosphorous (10%), Potassium (0%); and (4) Nitrogen (25%), Phosphorous (10%), Potassium (0%) and manure. Data were collected from two different areas of Cyprus (Nicosia and Larnaca) through on-site visits and questionnaires. Life Cycle Assessment (LCA) was used as a method to quantify environmental impacts which were categorized into six impact categories: (i) acidification potential (AP), (ii) eutrophication potential (EP), (iii) global warming potential (GWP), (iv) ozone depletion potential (ODP), (v) photochemical, ozone creation potential (POCP), and (vi) terrestrial ecotoxicity (TAETP). LCA was used with system boundaries from field to harvest and a functional unit (FU) of one bale of hay. Research results showed that the addition of manure increased values in all impact categories. Comparing scenarios without manure (1 and 3) and with manure (2 and 4), the main process which contributed to GWP was field preparation, which resulted in 3 t CO2-Eq∙FU-1 and 46.96 t CO2-Eq∙FU-1, respectively. Furthermore, the highest contribution of sub-processes to GWP (kg CO2-Eq∙FU-1) was machinery maintenance (scenarios 2 and 4). The potential to reduce environmental impacts from barley and moreover, to mitigate the footprint of the agriculture sector in Cyprus is proposed by changing existing practices such as decreasing fuel consumption by agricultural machinery, and monitoring fertilizing and seeding. Conclusively, the carbon footprint of barley can be decreased through the improvement of nutrient management and cropping practices.

Photovoltaic-driven electrochemical remediation of drilling fluid wastewater with simultaneous hydrogen production.

In this work, we studied the application of photovoltaic solar energy for driving the electrochemical processes of electrocoagulation and electrooxidation to remediate drilling fluid wastewater, and simultaneously harvest energy in the form of electrolytic hydrogen gas produced at the cathode. The electrocoagulation was performed with sacrificial aluminium electrodes and electrooxidation with dimensionally stable boron-doped diamond electrodes in batch-wise and continuously operated mode, and their efficiency in both pollutants removal and hydrogen gas production was elucidated. The parameters affecting the efficiency of the applied electrochemical processes, such as applied current density, pH, electroprocessing time and flow rate, were investigated. The electrochemical processing was monitored by measuring the chemical oxygen demand (COD) of treated wastewater. The electrocoagulation treatment conducted with current densities of 30, 60 and 90 mA/cm2 reduced the wastewater COD by about 67%, whereas the electrooxidation treatment at the same conditions yielded a COD removal of over 95%. The amount of produced hydrogen was 171 L/g COD removed from treated wastewater.

HS-SPME-GC/MS Analysis for Revealing Carob's Ripening.

Carob's recognized nutritional and medicinal value next to its unique agriculture importance is associated with an array of social, economic, and cultural activities. The carob fruit is popular for its intense aroma due to the emitted volatile organic compounds (VOCs). The composition of VOCs released from carob fruits changes during ripening, rendering it a non-invasive tool for the determination of the ripening period and freshness of the fruit. Therefore, headspace solid-phase microextraction gas chromatography/mass spectrometry (HS-SPME-GC/MS) was applied to reveal the respective gaseous signal molecules related to fruit maturity. The sampling was implemented during weeks 26-36 from five different locations in Cyprus. Additionally, the gaseous emissions of total VOCs (TVOCs) and carbon dioxide (CO2) were recorded next to the moisture content of the fruit. The major chemical classes in the ripening are acids, followed by esters, and ketones. More specifically, the most abundant VOCs during ripening are propanoic acid, 2-methyl-(isobutyric acid), 2-heptanone, propanoic acid, 2-methyl-, 2-methylbutyl ester, acetic acid, methyl isobutyrate, propanoic acid, 2-methyl-, 3-methylbutyl ester, 2-pentanone, butanoic acid and propanoic acid, 2-methyl-ethyl ester. Finally, CO2 emissions and moisture content showed a rapid decline until the 31st week and then stabilized for all examined areas. The methodology revealed variations in VOCs' profile during the ripening process.

Biogas upgrading to methane and removal of volatile organic compounds in a system of zero-valent iron and anaerobic granular sludge.

The current study presented a novel process of biogas upgrading to biomethane (higher than 97%) based on anaerobic sludge and zero-valent iron (ZVI) system. When ZVI was added into an aquatic system with anaerobic granular sludge (AnGrSl) under anaerobic abiotic conditions, H2 was generated. Then, the H2 and CO2 were converted by the hydrogenotrophic methanogens to CH4. Biogas upgrading to biomethane was achieved in 4 days in the AnGrSl system (50 g L-1 ZVI, initial pH 5 and 20 g L-1 NaHCO3). In this system, when zero-valent scrap iron (ZVSI) was added instead of ZVI, a more extended period (21 days) was required to achieve biogas upgrading. X-ray diffraction (XRD) analysis revealed that the materials in a reactor with CO2 or biogas headspace, exhibited a mixture of ferrite and the iron carbonate phase of siderite (FeCO3), with the latter being the dominant phase. VOCs analysis in raw biogas (in the system of anaerobic sludge and ZVI) highlighted the reduction of low mass straight- and branched-chain alkanes (C6-C10). Also, H2S and NH3 were found to be substantially reduced when the anaerobic sludge was exposed to ZVI compared to the cases where ZVI was not added. This study found that simultaneously with biogas upgrading, VOCs, H2S and NH3 can be removed in a system of ZVI or ZVSI and AnGrSl under aquatic anaerobic conditions.

TD-GC/MS analysis of indoor air pollutants (VOCs, PM) in hair salons.

Hairdressing personnel is daily exposed to various chemical air pollutants, and specifically to Volatile Organic Compounds (VOCs) and Particulate Matter (PM) in hair salons. This is of concern, due to the hazardous effects of these chemicals on the individual's health. Nevertheless, a limited exposure assessment of indoor air quality (IAQ) has been performed. The aim of this study was to analyze the indoor air in 5 hair salons, to assess the IAQ of the occupational exposure, and to identify the main VOCs produced or activities responsible for the respective indoor pollution. The chemical analysis took place inside the salon environment by monitoring the emitted VOCs, as well as the PM of 1, 2.5, 4, and 10 µm aerodynamic diameter. The sampling of VOCs was performed by adsorption of pollutants on Tenax TA sorbent tubes, that were subsequently analyzed using a thermal desorption unit coupled to gas chromatography/mass spectrometry (TD-GC/MS). The obtained results showed that hair products are a major source of air pollutants, as elevated concentrations of VOCs and PM are released in the working environment. Furthermore, the type and concentration of VOCs are affected by the various hair treatment activities taking place in the salons. Among the main compounds detected there was benzene, toluene, ethylbenzene, and xylenes, known as BTEX, as well as, diethyl phthalate, 1,4-dioxane, etc. More than 50 VOCs were identified (occurrence ≥60%) and 14 of them were quantified. Their average concentration levels varied from 12 µg m-3 for naphthalene to 941 µg m-3 for toluene. The measuring levels for PM revealed violations of the EPA and WHO international standards for permissible limit concentrations; this was the case in all hair treatment activities but mostly during keratin treatment. Hence, much more effort is needed to reduce the respective concentration levels of PM and VOCs, that contribute to self-reported health problems.

Development of food-origin biochars for the adsorption of selected volatile organic compounds (VOCs) for environmental matrices.

Four novel fruit-derived biochars were developed: pomegranate peels (PB), prickly pear peels (PPB), carob (CB), and locust bean gum (LBGB). The feedstocks were pyrolyzed at 350 and 550 ℃ (under N2), respectively, and characterized using Scanning Electron Microscopy (SEM), Elemental Analysis (EA), Diffuse Reflectance Infrared Fourier Transform Spectroscopy (DRIFTS), Brunauer-Emmett-Teller (B.E.T) analysis, and Thermogravimetric analysis (TGA). A systematic and comprehensive comparison for the adsorption of selected volatile organic compounds (VOCs) by biochar was established. Cresol, dimethyl trisulfide (DMTS), hexane, and benzene were examined as a function of contact time (30-480 min), mass (0.1-1 g), concentration levels (50-1000 ppbv), efficiency, and reusability, using the headspace solid-phase microextraction gas chromatography-mass spectrometry (HS-SPME-GC-MS) method. PB 550 ℃ revealed a specific surface area of 8.3 m2 g-1, the fastest complete removal, an ideal mass of 1 g, 3-times reuse, and âˆ¼ 99% removal of 500 ppbv benzene, cresol, DMTS, and 100 ppbv hexane.

Oil biodesulfurization: A review of applied analytical techniques.

The wide use of fossil fuels and their associated environmental concerns, highlighted the importance of affordable and clean energy (goal 7), as adopted by the Sustainable Development Goals of the United Nations for 2030. For years now, the detection of sulfur components in liquid fuels is performed mainly for environmental and health purposes in compliance with the respective legislations. Towards this, the aerobic and anaerobic biodesulfurization (BDS) process, which entails the use of microorganisms to limit the sulfur concentration is followed. To ensure effective BDS, several traditional analytical methods are utilized, although they require bench-top, bulky, costly, and time-consuming instruments along with skilled personnel. The currently employed analytical methods are mostly chromatographic techniques (e.g. liquid and gas) coupled with various detectors. To start with, high-performance liquid chromatography with ultraviolet detector (HPLC-UV), as well as electrospray ionization-LC-mass spectrometry (ESI-LC-MS) were mostly reported. Additionally, many detectors were coupled to gas chromatography (CG) including atomic emission detector (GC-AED), flame ionization detector (GC-FID), flame photometric detector (GC-FPD), sulfur fluorescence detector (GC-SFD), mass selective detector (GC-MS), etc. The solid-phase microextraction (SPME) technique provides extra capabilities when added to the separation techniques. Towards the continuous interest in oil supercomplex synthesis, other atmospheric and surface desorption ionization techniques, as well as the multidimensional 2D chromatographic systems (GC × GC and LC × LC) were also investigated, due to their unsurpassed resolution power. The current review ends with final remarks per applied methodology and the necessity to respect and protect the human environment and life.

Use of biochar for the sorption of volatile organic compounds (VOCs) emitted from cattle manure.

The ability of biochar to be used as filter or as additive for the adsorption of volatile organic compounds (VOCs) emitted from cattle manure is investigated. The employed biochar was produced from cattle manure after slow pyrolysis at 550 °C (under nitrogen). Towards this, in-house-made glass emission reactors were filled with fresh cattle manure samples and a thin layer of biochar (10% w/w) was placed on the top of the manure layer. The mixture was left for 24 h to equilibrate and air samples were collected from the headspace air. The samples were then analyzed using the headspace solid-phase micro-extraction gas chromatography-mass spectrometry (HS-SPME-GC-MS) method. Cattle manure emissions are considered unpleasant and odoriferous. The respective changes in the emitted cattle manure VOCs were reported; these included mainly reduction in sulfur- (thiols and sulfides) and oxygen-containing VOCs (alcohols, ketones, phenolics), showing a promising application of biochar for the removal of such compounds from manure wastes. Also, five VOCs were selected as sorbents for further laboratory studies: hexane, dimethyl trisulfide, phenol, p-cresol, and 2-methyl-3-pentanone. The results of cattle manure-derived biochar, revealed a reduction in their emitted concentrations (low ppbv). The present application highlights a straightforward example of cyclic economy, where a waste product is reused after being processed; its re-usage as odor adsorbent serves again the agriculture sector.

Native plants for the remediation of abandoned sulphide mines in Cyprus: A preliminary assessment.

Mining in Cyprus resulted in a significant number of abandoned sulphide mines without any rehabilitation measures. The present study aims to describe and compare the environmental parameters in three such mines with respect to water chemistry, waste dumps geochemistry, slope-topography and plant growth. The mines under study are that of Kokkinopezoula, North and South Mathiatis located at the northeast of the Troodos massif. A synopsis of the previous studies conducted for the above-mentioned mines is presented, which includes water and soil samples analyses. Although, in these areas environmental degradation is reported, there are some plants which grow naturally. Therefore, a preliminary attempt to report these plants is conducted, while remediation options presented in the literature including technosols, revegetation, phytoremediation and phytostabilization are proposed. Potential use of native plants such as Phragmites australis, Tamarix smyrnensis, Poaceae, Pinus brutia and Schoenus nigricans Poaceace could be applied for phytoremediation of the sulphide mines in Cyprus. These plants seem to have great strength at low pH values and high metal content in contaminated soils and water. The three mines under study are also compared with three other old mines located in the broader area of Cyprus; that of Xeros, Limni and Skouriotissa, which operated under similar climatic conditions. By improving abandoned mines environment with technosols, the action of native plants will be enhanced and thus work towards a successful phytoremediation treatment, resulting in the minimization of future pollutants generated by the solid waste dumps.

Use of Chemometrics for Correlating Carobs Nutritional Compositional Values with Geographic Origin.

Carobs unique compositional and biological synthesis enables their characterization as functional foods. In the present study, 76 samples derived from fruit and seeds of carobs, with origin from the countries of the Mediterranean region (Cyprus, Greece, Italy, Spain, Turkey, Jordan and Palestine) were analyzed for their nutritional composition, in order to identify potential markers for their provenance and address the carobs' authenticity issue. Moisture, ash, fat, proteins, sugars (fructose, glucose, sucrose), dietary fibers and minerals (Ca, K, Mg, Na, P, Cu, Fe, Mn, Zn) were estimated following official methods. Due to the large number of data (76 samples × 17 parameters × 7 countries), chemometric techniques were employed to process them and extract conclusions. The samples of different geographical origin were discriminated with 79% success in total. The carobs from Cyprus, Italy and Spain were correctly classified without error. The main discriminators were found to be the dietary fibers, the carbohydrates and Cu, Zn and Mn, which emphasize their specific nutritional added value to the product and the country of origin impact. The results suggest that the proposed analytical approach is a powerful tool that enables the discrimination of carobs based on their country of origin. This research contributes to authenticity of carobs, adding value to local products.

Correction to: Assessing the volatile profile of carob tree (Ceratonia siliqua L.).

The original publication of this paper contains an error.

Assessing the volatile profile of carob tree (Ceratonia siliqua L.).

Biogenic volatile organic compounds (VOCs) contribute to the communication, growth, breeding, and defense of plant; their role in plant kingdom is vital. Carob tree is cultivated mainly in Middle East and eastern European countries (e.g., Spain, Italy, Greece, Cyprus) and lately in Australia, the USA, and South Africa. Therefore, it is examined as a case study for its volatile emissions in the environment. Apart from the VOCs emitted from carob flowers and fruit, carob is considered of great interest for the food industry (carob powder), not only for its health benefits but also due to its characteristic strong aroma, which can be maintained even after processing (roasting). Solid-phase microextraction/gas chromatography-mass spectrometry (SPME/GC-MS) analyses of carob flowers, fruit, and powder (commercial samples) were performed and the detected VOCs are presented and discussed. The most prominent chemical classes emitted from carob fruit and powder appeared to be acids followed by esters and aldehydes/ketones, whereas from carob flowers the terpenoids. The strongest VOCs both in carob fruits and powder were propanoic acid, 2-methyl (isobutyric acid) and in flowers ethanol. The uniqueness of carob benefits is well known in the agriculture, pharmaceutical, cosmetic, and food sector and is closely related to the agro-economy and long history of eastern Mediterranean countries.

Laboratory Testing in Support of Surfactant-Alternating-Gas Foam Flood for NAPL Recovery from Shallow Subsurface.

Use of viscosifiers have been shown helpful for mobility control when displacing higher viscosity fluids, and to improve sweep in heterogeneous media. Foam can be used as a viscosifier for this purpose. Selected surfactant solutions were investigated for their ability to generate foam within porous media and foam stability through batch and column experiments using field-obtained soil. The approach used to generate foam in-situ consisted of several cycles (7) of surfactant-alternating-gas originally developed to recover crude oil; 0.25 pore volumes (PV) surfactant followed by 0.25 PV of air. The apparent viscosity ranged from 60 to 100 cP from the 3rd to 7th cycle, respectively. Foam was collected from the column exit after being shut-in for 3 days as a proof of foam generation and stability. Results showed that the selected surfactant formulation can be used to generate foam in-situ for use in the field for environmental restoration.

Converting environmental risks to benefits by using spent coffee grounds (SCG) as a valuable resource.

Coffee is perhaps one of the most vital ingredients in humans' daily life in modern world. However, this causes the production of million tons of relevant wastes, i.e., plastic cups, aluminum capsules, coffee chaff (silver skin), and spent coffee grounds (SCG), all thrown untreated into landfills. It is estimated that 1 kg of instant coffee generates around 2 kg of wet SCG; a relatively unique organic waste stream, with little to no contamination, separated directly in the source by the coffee shops. The produced waste has been under researchers' microscope as a useful feedstock for a number of promising applications. SCG is considered a valuable, nutrients rich source of bioactive compounds (e.g., phenolics, flavonoids, carotenoids, lipids, chlorogenic and protocatechuic acid, melanoidins, diterpenes, xanthines, vitamin precursors, etc.) and a useful resource material in other processes (e.g., soil improver and compost, heavy metals absorbent, biochar, biodiesel, pellets, cosmetics, food, and deodorization products). This paper aims to provide a holistic approach for the SCG waste management, highlighting a series of processes and applications in environmental solutions, food industry, and agricultural sector. Thus, the latest developments and approaches of SCG waste management are reviewed and discussed.

Jet A fuel recovery using micellar flooding: Design and implementation.

Surfactants offer two mechanisms for recovering NAPLs: 1) to mobilize NAPL by reducing NAPL/water interfacial tension, and; 2) to increase the NAPL's aqueous solubility-called solubilization-as an enhancement to pump & treat. The second approach has been well-studied and applied successfully in several pilot-scale and a few full-scale tests within the last 15years, known as Surfactant Enhanced Aquifer Remediation (SEAR). A useful source of information for this second approach is the "Surfactant-enhanced aquifer remediation (SEAR) design manual" from the U.S. Navy Facilities Engineering Command. Few attempts, however, have been made at recovering NAPLs using the mobilization approach presented in this paper. Now, a full-scale field implementation of the mobilization approach is planned to recover an LNAPL (Jet A fuel) from a surficial sand aquifer located in Denmark using a smaller amount of surfactant solution and fewer PVs of throughput compared with the SEAR approach. The approach will rely on mobilizing the LNAPL so that it is recovered ahead of the surfactant microemulsion, also known as a micellar flood. This paper will review the laboratory work performed as part of the design for a full-scale implementation of a micellar flood. Completed lab work includes screening of surfactants, phase behavior and detailed salinity scans of the most promising formulations, and generating a ternary diagram to be used for the numerical simulations of the field application. The site owners and regulators were able to make crucial decisions such as the anticipated field results based on this work.