ABSTRACT
Enhanced non-linearity and asymmetric behavior of the Cr/metal oxide diode is reported, with the addition of two insulator layers of SnO2 and NiO to form the metal-insulator-insulator-metal (MIIM) configuration. Such an MIIM diode shows potential for various applications (rectifiers and electronic equipment) which enable the femtosecond fast intoxication in MIIM diodes. In this work, nanostructured multi-layer Cr/SnO2/NiO/Cr coatings were fabricated via e-beam evaporation with the following thicknesses: 150 nm/20 nm/10 nm/150 nm. Coatings were characterized via Rutherford backscattering (RBS), scanning electron microscopy (SEM), and two-probe conductivity testing. RBS confirmed the layered structure and optimal stoichiometry of the coatings. A non-linear and asymmetric behavior at <1.5 V applied bias with the non-linearity maximum of 2.6 V−1 and the maximum sensitivity of 9.0 V−1 at the DC bias point was observed. The promising performance of the coating is due to two insulating layers which enables resonant tunneling and/or step-tunneling. Based on the properties, the present multi-layer coatings can be employed for MIIM application.
ABSTRACT
Nanocomposite multi-layer TiO2/V2O5/TiO2 thin films were prepared via electron-beam evaporation using high-purity targets (TiO2 and V2O5 purity > 99.9%) at substrate temperatures of 270 °C (TiO2) and 25 °C (V2O5) under a partial pressure of oxygen of 2 × 10−4 mbar to maintain the stoichiometry. Rutherford backscattering spectrometry was used to confirm the layer structure and the optimal stoichiometry of the thin films, with a particle size of 20 to 40 nm. The thin films showed an optical transmittance of ~78% in the visible region and a reflectance of ~90% in the infrared. A decrease in transmittance was observed due to the greater cumulative thickness of the three layers and multiple reflections at the interface of the layers. The optical bandgap of the TiO2 mono-layer was ~3.49 eV, whereas that of the multi-layer TiO2/V2O5/TiO2 reached ~3.51 eV. The increase in the optical bandgap was due to the inter-diffusion of the layers at an elevated substrate temperature during the deposition. The intrinsic, structural, and morphological features of the TiO2/V2O5/TiO2 thin films suggest their efficient use as a solar water heater system.
ABSTRACT
The influence of nanodiamonds (NDs) on the thermal and ablative performance of carbon-fiber-reinforced-epoxy matrix compositeswas explored. The ablative response of the composites with 0.2 wt% and 0.4 wt% NDs was studied through pre-and post-burning morphologies of the composite surfaces by evaluation of temperature profiles, weight loss, and erosion rate. Composites containing 0.2 wt% NDs displayed a 10.5% rise in erosion resistance, whereas composites containing 0.4 wt% NDs exhibited a 12.6% enhancement in erosion resistance compared to neat carbon fiber-epoxy composites. A similar trend was witnessed in the thermal conductivity of composites. Incorporation of composites with 0.2 wt% and 0.4 wt% NDs brought about an increase of 37 wt% and 52 wt%, respectively. The current study is valuable for the employment of NDs in carbon fiber composite applications where improved erosion resistance is necessary.
ABSTRACT
Interfacial bonding highly affects the quality of bimetallic bearing materials, which primarily depend upon the surface quality of a solid metal substrate in liquid-solid compound casting. In many cases, an intermediate thin metallic layer is deposited on the solid substrate before depositing the liquid metal, which improves the interfacial bonding of the opposing materials. The present work aims to develop and optimize the tinning process of a solid carbon steel substrate after incorporating flux constituents with the tin powder. Five ratios of tin-to-flux-i.e., 1:1, 1:5, 1:10, 1:15, and 1:20-were used for tinning process of carbon steel solid substrate. Furthermore, the effect of volume ratios of liquid Al-based bearing alloy to solid steel substrate were also varied-i.e., 5:1, 6.5:1 and 8.5:1-to optimize the microstructural and mechanical performance, which were evaluated by interfacial microstructural investigation, bonding area determination, hardness and interfacial strength measurements. It was found that a tin-to-flux ratio of 1:10 offered the optimum performance in AlSn12Si4Cu1/steel bimetallic materials, showing a homogenous and continuous interfacial layer structure, while tinned steels using other percentages showed discontinuous and thin layers, as in 1:5 and 1:15, respectively. Furthermore, bimetallic interfacial bonding area and hardness increased by increasing the volume ratio of liquid Al alloy to solid steel substrate. A complete interface bonding area was achieved by using the volume ratio of liquid Al alloy to solid steel substrate of ≥8.5.
ABSTRACT
Sn-based Babbitt alloy was reinforced with alumina nanoparticles to prepare a novel class of nanocomposites. The route of liquid metallurgy in combination with stirring mechanism was chosen to prepare nanocomposites with three different loadings of alumina nanoparticles, i.e., 0.25 wt%, 0.50 wt% and 1.0 wt%. The molten mixture of metallic matrix and nanoparticles was poured over carbon steel substrate for solidification to manufacture a bimetallic material for bearing applications. The underlying aim was to understand the effect of nanoparticle addition on microstructural variation of Sn-based Babbitt alloy as well as bimetallic microstructural interface. The addition of 0.25 wt% and 0.50 wt% alumina nanoparticles significantly affected both the morphology and distribution of Cu6Sn5 hard phase in solid solution, which changed from needle and asterisk shape to spherical morphology. Nanocomposites containing up to 0.50 wt% nanoparticles showed more improvement in tensile strength than the one containing 1.0 wt% nanoparticles, due to nanoparticle-agglomeration and micro-cracks at the interface. The addition of 0.5 wt% nanoparticles significantly improved the wear resistance of Sn-based Babbitt alloy.
ABSTRACT
A novel tweakable nanocomposite was prepared by spark plasma sintering followed by systematic oxidation of carbon nanotube (CNT) molecules to produce alumina/carbon nanotube nanocomposites with surface porosities. The mechanical properties (flexural strength and fracture toughness), surface area, and electrical conductivities were characterized and compared. The nanocomposites were extensively analyzed by field emission scanning electron microscopy (FE-SEM) for 2D qualitative surface morphological analysis. Adding CNTs in ceramic matrices and then systematically oxidizing them, without substantial reduction in densification, induces significant capability to achieve desirable/application oriented balance between mechanical, electrical, and catalytic properties of these ceramic nanocomposites. This novel strategy, upon further development, opens new level of opportunities for real-world/industrial applications of these relatively novel engineering materials.
Subject(s)
Ceramics/chemistry , Nanocomposites/chemistry , Nanotubes, Carbon/chemistry , Aluminum Oxide/chemistry , Electric Conductivity , Nanocomposites/ultrastructure , Nanotubes, Carbon/ultrastructureABSTRACT
This paper elucidates the effect of silicon carbide nanoparticles (SiCNP) and graphene nanoplatelets (GNPs), on their own and together, on the densification behavior and fracture toughness of alumina (Al2O3) ceramic matrix. This was investigated by using the high-frequency induction heat sintering (HFIHS) process. While the addition of each nanostructure caused varying degrees of grain refinement and enhancement of mechanical properties, the incorporation of as little as 0.5 wt.% GNPs along with 5.0 wt.% SiCNP promoted uniform dispersion of the latter due to the lateral surface area of the graphene nanosheets with their two-dimensional morphology. There was an associated reduction in grain size from 1500 to 300 nm upon the addition of both types of nanoscale reinforcements. Extensive electron microscopy of the as-produced nanocomposites indicated the presence of SiCNP within, as well as at, the grain boundary areas whereas the 2D GNPs anchored between neighboring grains. Fractography of the samples revealed a transition from a mixed intergranular/transgranular mode for SiCNP or GNP-reinforced nanocomposites to transgranular fracture mode for the hybrid nanocomposites with improvements in fracture toughness and microhardness by 160 and 27%, respectively, largely due to the synergic role of the nanostructured reinforcements and their distinctly different toughening mechanisms. A new toughening model is proposed for the hybrid nanocomposites by taking into consideration crack deflection and pull-out effects due to SiCNP and the atomic level slip-stick driven GNPs inter-layer slithering. It was found that the addition of GNPs facilitates SiCNP dispersion that subsequently develops dense, fine-grained microstructures after a short-cycle, pressure-assisted consolidation process.
