Hybrid Polymer Salogels for Reversible Entrapment of Salt-Hydrate-Based Thermal Energy Storage Materials.

One of the challenges preventing wide use of inorganic salt hydrate phase change materials (PCMs) is their low viscosity above their melting point, leading to leakage, phase segregation, and separation from heat exchanger surfaces in thermal management applications. The development of a broad strategy for using polymers that provide tunable, temperature-reversible shape stabilization of a variety of salt hydrates by using the lowest possible polymer concentrations is hindered by differences in solubility and gelation behavior of polymers with change in the type of ion. This work addressed the challenge of creating robust, temperature-responsive shape-stabilizing polymer gels (i.e., salogels) using a low cost PCM, calcium chloride hexahydrate (CaCl2·6H2O, CCH). Due to the extremely high (9 M) concentration of chloride ions and the tendency to salting-out polymer chains, the previous strategy of using single-polymer salogels was not successful. Thus, this work introduced a strategy of using two polymers, poly(vinyl alcohol) and ultrahigh molecular weight polyacrylamide (PVA and PAAm, respectively), along with borax as a cross-linker to achieve temperature-reversible, shape-stable salogels. This system resulted in robust salogels whose gel-to-sol transition temperature (Tgel) was tunable within an application-relevant range of gelation temperature (30-80 °C). This behavior was enabled by a synergistic combination of dynamic covalent cross-links between PVA units and entanglements of PAAm chains which were combined into a single hybrid network. The hybrid salogels had <5 wt % polymer content, maintaining ∼95% of the heat of fusion of the pure PCM. Importantly, the noncovalent nature of gelation supported thermo-reversibility of gelation, shape stability, and retention of thermal properties over 50 melting/crystallization cycles.

Effect of polyacid architecture and polycation molecular weight on lateral diffusion within multilayer films.

Despite the potential use of polyelectrolyte multilayers for biomedical, separation, and energy applications, their dynamic properties are not sufficiently understood. In this work, center-of-mass diffusion of a weak polyacid-poly(methacrylic acid) (PMAA) of linear and 8-arm architecture (L-PMAA and 8-PMAA, respectively) and matched molecular weight-was studied in layer-by-layer (LbL) assemblies with poly(diallyldimethylammonium) chloride (PDADMAC) of varied molecular weight. The film deposition at low-salt, acidic conditions when PMAA was only partially ionized yielded thicker, more diffused layers with shorter PDADMAC chains, and bilayer thickness decreased for multilayers constructed with longer PDADMAC. The molecular architecture of PMAA had a weak effect on film growth, with bilayer thickness being ∼20% larger for L-PMAA for the films constructed with the shortest PDADMAC (35 kDa) and identical film growth for L-PMAA and 8-PMAA with the longest PDADMAC (300 kDa). The exposure of the multilayer films to 0.2M NaCl triggered a reduction in PMAA ionization and significant lateral diffusivity of fluorescently labeled PMAA molecules (PMAA*), with diffusion coefficients D ranging from 10-13 to 10-12 cm2/s, as determined by the fluorescence recovery after photobleaching technique. For all the films, polymer mobility was higher for star polyacids as compared to their linear counterparts, and the dependence of PMAA diffusion coefficient D on PDADMAC molecular weight (D ∼ M-n) was relatively weak (n < 0.6). However, 8-PMAA demonstrated an approximately doubled power exponent compared to the L-PMAA chains, suggesting a stronger effect of the molecular connectivity of the partner polycation molecules on the diffusion of star polyelectrolytes.

Engineering Degradation Rate of Polyphosphazene-Based Layer-by-Layer Polymer Coatings.

Degradable layer-by-layer (LbL) polymeric coatings have distinct advantages over traditional biomedical coatings due to their precision of assembly, versatile inclusion of bioactive molecules, and conformality to the complex architectures of implantable devices. However, controlling the degradation rate while achieving biocompatibility has remained a challenge. This work employs polyphosphazenes as promising candidates for film assembly due to their inherent biocompatibility, tunability of chemical composition, and the buffering capability of degradation products. The degradation of pyrrolidone-functionalized polyphosphazenes was monitored in solution, complexes and LbL coatings (with tannic acid), providing the first to our knowledge comparison of solution-state degradation to solid-state LbL degradation. In all cases, the rate of degradation accelerated in acidic conditions. Importantly, the tunability of the degradation rate of polyphosphazene-based LbL films was achieved by varying film assembly conditions. Specifically, by slightly increasing the ionization of tannic acid (near neutral pH), we introduce electrostatic "defects" to the hydrogen-bonded pairs that accelerate film degradation. Finally, we show that replacing the pyrrolidone side group with a carboxylic acid moiety greatly reduces the degradation rate of the LbL coatings. In practical applications, these coatings have the versatility to serve as biocompatible platforms for various biomedical applications and controlled release systems.

4-Methylumbelliferone-Functionalized Polyphosphazene and Its Assembly into Biocompatible Fluorinated Nanocoatings with Selective Antiproliferative Activity.

Advanced multifunctional biomaterials are increasingly relying on clinically dictated patterns of selectivity against various biological targets. Integration of these frequently conflicting features into a single material surface may be best achieved by combining various complementary methodologies. Herein, a drug with a broad spectrum of activity, i.e., 4-methylumbelliferone (4-MU), is synthetically multimerized into water-soluble anionic macromolecules with the polyphosphazene backbone. The polymer structure, composition, and solution behavior are studied by 1H and 31P NMR spectroscopy, size-exclusion chromatography, dynamic light scattering, and UV and fluorescence spectrophotometry. To take advantage of the clinically proven hemocompatibility of fluorophosphazene surfaces, the drug-bearing macromolecule was then nanoassembled onto the surface of selected substrates in an aqueous solution with fluorinated polyphosphazene of the opposite charge using the layer-by-layer (LbL) technique. Nanostructured 4-MU-functionalized fluoro-coatings exhibited a strong antiproliferative effect on vascular smooth muscle cells (VSMCs) and fibroblasts with no cytotoxicity against endothelial cells. This selectivity pattern potentially provides the opportunity for highly desirable fast tissue healing while preventing the overgrowth of VSMCs and fibrosis. Taken together with the established in vitro hemocompatibility and anticoagulant activity, 4-MU-functionalized fluoro-coatings demonstrate potential for applications as restenosis-resistant coronary stents and artificial joints.

Salt-Induced Diffusion of Star and Linear Polyelectrolytes within Multilayer Films.

This study explores the effect of salt on the diffusivity of polyelectrolytes of varied molecular architecture in layer-by-layer (LbL) films in directions parallel and perpendicular to the substrate using fluorescence recovery after photobleaching (FRAP) and neutron reflectivity (NR) techniques, respectively. A family of linear, 4-arm, 6-arm, and 8-arm poly(methacrylic acids) (LPMAA, 4PMAA, 6PMAA, and 8PMAA, respectively) of matched molecular weights were synthesized using atom transfer radical polymerization and assembled with a linear polycation, poly[2-(trimethylammonium)ethyl methacrylate chloride] (QPC). NR studies involving deuterated QPC revealed ∼10-fold higher polycation mobility for the 8PMAA/QPC system compared to all-linear LbL films upon exposure to 0.25 M NaCl solutions at pH 6. FRAP experiments showed, however, that lateral diffusion of star PMAAs was lower than LPMAA at NaCl concentrations below ∼0.22 M NaCl, with a crossover to higher mobility of star polymers in more concentrated salt solutions. The stronger response of diffusion of star PMAA to salt is discussed in the context of several theories previously suggested for diffusivity of polyelectrolyte chains in multilayer films and coacervates.

Factors Controlling Degradation of Biologically Relevant Synthetic Polymers in Solution and Solid State.

The field of biodegradable synthetic polymers, which is central for regenerative engineering and drug delivery applications, encompasses a multitude of hydrolytically sensitive macromolecular structures and diverse processing approaches. The ideal degradation behavior for a specific life science application must comply with a set of requirements, which include a clinically relevant kinetic profile, adequate biocompatibility, benign degradation products, and controlled structural evolution. Although significant advances have been made in tailoring materials characteristics to satisfy these requirements, the impacts of autocatalytic reactions and microenvironments are often overlooked resulting in uncontrollable and unpredictable outcomes. Therefore, roles of surface versus bulk erosion, in situ microenvironment, and autocatalytic mechanisms should be understood to enable rational design of degradable systems. In an attempt to individually evaluate the physical state and form factors influencing autocatalytic hydrolysis of degradable polymers, this Review follows a hierarchical analysis that starts with hydrolytic degradation of water-soluble polymers before building up to 2D-like materials, such as ultrathin coatings and capsules, and then to solid-state degradation. We argue that chemical reactivity largely governs solution degradation while diffusivity and geometry control the degradation of bulk materials, with thin "2D" materials remaining largely unexplored. Following this classification, this Review explores techniques to analyze degradation in vitro and in vivo and summarizes recent advances toward understanding degradation behavior for traditional and innovative polymer systems. Finally, we highlight challenges encountered in analytical methodology and standardization of results and provide perspective on the future trends in the development of biodegradable polymers.

Mid-Infrared Serial Microring Resonator Array for Real-Time Detection of Vapor-Phase Volatile Organic Compounds.

Chip-scale infrared spectrometers consisting of a microring resonator array (MRA) were developed for volatile organic compound (VOC) detection. The MRA is serially positioned to serve as a wavelength sorting element that enables wavelength demultiplexing. Unlike conventional devices operated by a single microring, our MRA can perform multiwavelength mid-infrared (mid-IR) sensing by routing the resonant wavelength light from a broadband mid-IR source into different sensing channels. Miniaturized spectrometer devices were fabricated on mid-IR transparent silicon-rich silicon nitride (SiNx) thin films through complementary metal-oxide-semiconductor (CMOS) processes, thus enabling wafer-level manufacturing and packaging. The spectral distribution of the resonance lines and the optimization of the microring structures were designed using finite-difference time-domain (FDTD) modeling and then verified by laser spectrum scanning. Using small microring structures, the spectrum showed a large free spectral range (FSR) of 100 nm and held four spectral channels without crosstalk. Unlike near-infrared microrings using refractive index sensing, our MRA can detect hexane and ethanol vapor pulses by monitoring the intensity variation at their characteristic mid-IR absorption bands, thus providing high specificity. Applying multiwavelength detection, the sensor module can discriminate among various VOC vapors. Hence, our mid-IR MRA could be an essential component to achieve a compact spectroscopic sensing module that has the potential for applications such as remote environmental monitoring and portable health care devices.

Hierarchically Structured, All-Aqueous-Coated Hydrophobic Surfaces with pH-Selective Droplet Transfer Capability.

Often inspired by nature, techniques for precise droplet manipulation have found applications in microfluidics, microreactors, and water harvesting. However, a widely applicable strategy for surface modification combining simultaneous hydrophobicity and pH-sensitivity has not yet been achieved by employing environmentally friendly assembly conditions. The introduction of pH-responsive groups to an otherwise fluorinated polyphosphazene (PPZ) unlocks pH-selective droplet capture and transfer. Here, an all-aqueous layer-by-layer (LbL) deposition of polyelectrolytes is used to create unique hydrophobic coatings, endowing surfaces with the ability to sense environmental pH. The high hydrophobicity of these coatings (ultimately reaching a contact angle >120° on flat surfaces) is enabled by the formation of hydrophobic nanoscale domains and controllable by the degree of fluorination of PPZs, polyamine-binding partners, deposition pH, and coating thickness. Inspired by the hierarchical structure of rose petals, these versatile coatings reach a contact angle >150° when deposited on structured surfaces while introducing a tunable adhesivity that enables precise droplet manipulation. The films exhibited a strongly pronounced parahydrophobic rose petal behavior characterized through the contact angle hysteresis. Depositing as few as five bilayers (∼25 nm) on microstructured rather than smooth substrates resulted in superhydrophobicity with water contact angles >150° and the attenuation of the contact angle hysteresis, enabling highly controlled transfer of aqueous droplets. The pH-selective droplet transfer was achieved between surfaces with either the same microstructure and LbL film building blocks, which were assembled at different pH, or between surfaces with different microstructures coated with identical films. The demonstrated capability of these hydrophobic LbL films to endow surfaces with controlled hydrophobicity through adsorption from aqueous solutions and control the adhesion and transfer of water droplets between surfaces can be used in droplet-based microfluidics applications and water collection/harvesting.

Detection of volatile organic compounds using mid-infrared silicon nitride waveguide sensors.

Mid-infrared (mid-IR) sensors consisting of silicon nitride (SiN) waveguides were designed and tested to detect volatile organic compounds (VOCs). SiN thin films, prepared by low-pressure chemical vapor deposition (LPCVD), have a broad mid-IR transparent region and a lower refractive index (nSiN = 2.0) than conventional materials such as Si (nSi = 3.4), which leads to a stronger evanescent wave and therefore higher sensitivity, as confirmed by a finite-difference eigenmode (FDE) calculation. Further, in-situ monitoring of three VOCs (acetone, ethanol, and isoprene) was experimentally demonstrated through characteristic absorption measurements at wavelengths λ = 3.0-3.6 µm. The SiN waveguide showed a five-fold sensitivity improvement over the Si waveguide due to its stronger evanescent field. To our knowledge, this is the first time SiN waveguides are used to perform on-chip mid-IR spectral measurements for VOC detection. Thus, the developed waveguide sensor has the potential to be used as a compact device module capable of monitoring multiple gaseous analytes for health, agricultural and environmental applications.

Cationic Fluoropolyphosphazenes: Synthesis and Assembly with Heparin as a Pathway to Hemocompatible Nanocoatings.

The development of state-of-the-art blood-contacting devices can be advanced through integrating hemocompatibility, durability, and anticoagulant functionalities within engineered nanoscale coatings. To enable all-aqueous assembly of nanocoatings combining omniphobic fluorinated features with the potent anticoagulant activity of hydrophilic heparin, two fluoropolymers containing cationic functionalities were synthesized─poly[(trifluoroethoxy)(dimethylaminopropyloxy)phosphazene], PFAP-O, and poly[(trifluoroethoxy)(dimethylaminopropylamino)phosphazene], PFAP-A. Despite a relatively high content of fluorinated pendant groups─approximately 50% (mol) in each─both polymers displayed solubility in aqueous solutions and were able to spontaneously form stable supramolecular complexes with heparin, as determined by dynamic light scattering and asymmetric flow field-flow fractionation methods. Heparin-containing coatings were then assembled by layer-by-layer deposition in aqueous solutions. Nanoassembled coatings were evaluated for potential thrombogenicity in three important categories of in vitro tests─coagulation by thrombin generation, platelet retention, and hemolysis. In all assays, heparin-containing fluoro-coatings consistently displayed superior performance compared to untreated titanium surfaces or fluoro-coatings assembled using poly(acrylic acid) in the absence of heparin. Short-term stability studies revealed the noneluting nature of these noncovalently assembled coatings.

Integrating Antioxidant Functionality into Polymer Materials: Fundamentals, Strategies, and Applications.

While antioxidants are widely known as natural components of healthy food and drinks or as additives to commercial polymer materials to prevent their degradation, recent years have seen increasing interest in enhancing the antioxidant functionality of newly developed polymer materials and coatings. This paper provides a critical overview and comparative analysis of multiple ways of integrating antioxidants within diverse polymer materials, including bulk films, electrospun fibers, and self-assembled coatings. Polyphenolic antioxidant moieties with varied molecular architecture are in the focus of this Review, because of their abundance, nontoxic nature, and potent antioxidant activity. Polymer materials with integrated polyphenolic functionality offer opportunities and challenges that span from the fundamentals to their applications. In addition to the traditional blending of antioxidants with polymer materials, developments in surface grafting and assembly via noncovalent interaction for controlling localization versus migration of antioxidant molecules are discussed. The versatile chemistry of polyphenolic antioxidants offers numerous possibilities for programmed inclusion of these molecules in polymer materials using not only van der Waals interactions or covalent tethering to polymers, but also via their hydrogen-bonding assembly with neutral molecules. An understanding and rational use of interactions of polyphenol moieties with surrounding molecules can enable precise control of concentration and retention versus delivery rate of antioxidants in polymer materials that are critical in food packaging, biomedical, and environmental applications.

Hydrogen-Bonded Complexes of Star Polymers.

The effect of molecular architecture, star versus linear, poly(ethylene oxide) (PEO) on the formation of hydrogen-bonded complexes with linear poly(methacrylic acid) (PMAA) is investigated experimentally and rationalized theoretically. Isothermal titration calorimetry reveals that at pH 2.5 interpolymer complexes (IPCs) of PMMA with a 6-arm star PEO (sPEO) contains ≈50% more polyacid than IPCs formed with linear PEO (lPEO). While the enthalpy of IPC formation is positive in both cases, its magnitude is ≈50% larger for sPEO/PMAA complexes that exhibit a lower dissociation constant than lPEO/polyacid complexes. These results are rationalized based on a higher localized density of hydrogen bonds formed between sPEO and the polyacid which prevents penetration of star molecules into PMAA coils. Accordingly, Fourier transform infrared results indicate approximately twofold excess of self-associated >COOH units over intermolecularly bonded >COOH units in sPEO-containing complexes. The excess of PMAA chains in IPCs and the percentage of self-associated carboxylic groups in sPEO/PMAA complexes both increase with polyacid molecular weight. Other findings, including a positive entropy, hysteresis in composition at strongly acidic pH, and progressive equilibration of IPCs at increased pH are consistent with the critical role of charge and release of water molecules in the formation of sPEO/PMAA and lPEO/PMAA complexes.

Selective hydrogen bonding controls temperature response of layer-by-layer upper critical solution temperature micellar assemblies.

This work establishes a correlation between the selectivity of hydrogen-bonding interactions and the functionality of micelle-containing layer-by-layer (LbL) assemblies. Specifically, we explore LbL films formed by assembly of poly(methacrylic acid) (PMAA) and upper critical solution temperature block copolymer micelles (UCSTMs) composed of poly(acrylamide-co-acrylonitrile) P(AAm-co-AN) cores and polyvinylpyrrolidone (PVP) coronae. UCSTMs had a hydrated diameter of ∼380 nm with a transition temperature between 45 and 50 °C, regardless of solution pH. Importantly, micelles were able to hydrogen-bond with PMAA, with the critical interaction pH being temperature dependent. To better understand the thermodynamic nature of these interactions, in depth studies using isothermal titration calorimetry (ITC) were conducted. ITC reveals opposite signs of enthalpies for binding of PMAA with micellar coronae vs. with the cores. Moreover, ITC indicates that pH directs the interactions of PMAA with micelles, selectively enabling binding with the micellar corona at pH 4 or with both the corona and the core at pH 3. We then explore UCSTM/PMAA LbL assemblies and show that the two distinct modes of PMAA interaction with the micelles (i.e. whether or not PMAA binds with the core) had significant effects on the film composition, structure, and functionality. Consistent with PMAA hydrogen bonding with the P(AAm-co-AN) micellar cores, a significantly higher fraction of PMAA was found within the films assembled at pH 3 compared to pH 4 by both spectroscopic ellipsometry and neutron reflectometry. Selective interaction of PMAA with PVP coronae of the assembled micelles, achieved by the emergence of partial ionization of PMAA at pH 4 was critical for preserving film functionality demonstrated as temperature-controlled swelling and release of a model small molecule, pyrene. The work done here can be applied to a multitude of assembled polymer systems in order to predict suppression/retention of their stimuli-responsive behavior.

Polyphosphazenes enable durable, hemocompatible, highly efficient antibacterial coatings.

Biocompatible antibacterial coatings are highly desirable to prevent bacterial colonization on a wide range of medical devices from hip implants to skin grafts. Traditional polyelectrolytes are unable to directly form coatings with cationic antibiotics at neutral pH and suffer from high degrees of antibiotic release upon exposure to physiological concentrations of salt. Here, novel inorganic-organic hybrid polymer coatings based on direct layer-by-layer assembly of anionic polyphosphazenes (PPzs) of various degrees of fluorination with cationic antibiotics (polymyxin B, colistin, gentamicin, and neomycin) are reported. The coatings displayed low levels of antibiotic release upon exposure to salt and pH-triggered response of controlled doses of antibiotics. Importantly, coatings remained highly surface active against Escherichia coli and Staphylococcus aureus, even after 30 days of pre-exposure to physiological conditions (bacteria-free) or after repeated bacterial challenge. Moreover, coatings displayed low (<1%) hemolytic activity for both rabbit and porcine blood. Coatings deposited on either hard (Si wafers) or soft (electrospun fiber matrices) materials were non-toxic towards fibroblasts (NIH/3T3) and displayed controllable fibroblast adhesion via PPz fluorination degree. Finally, coatings showed excellent antibacterial activity in ex vivo pig skin studies. Taken together, these results suggest a new avenue to form highly tunable, biocompatible polymer coatings for medical device surfaces.

All-nanoparticle layer-by-layer coatings for Mid-IR on-chip gas sensing.

Functionalization of optical waveguides with submicron coatings of zinc peroxide (ZnO2) and silica (SiO2) nanoparticles (NPs) is reported that enabled selective concentration of acetone vapors in the vicinity of the waveguide, boosting the sensitivity of a mid infrared (MIR) on-chip detector. Controlled thickness was achieved by introducing precise control of the substrate withdrawal speed to the layer-by-layer (LbL) deposition technique.

Solvation and diffusion of poly(vinyl alcohol) chains in a hydrated inorganic ionic liquid.

While the behavior of polyelectrolyte chains in aqueous salt solutions has been extensively studied, little is known about polar polymer chains in solvents with extremely high concentrations of inorganic ions, such as those found in ionic liquids (ILs). Here, we report on expansion, solvation and diffusion of poly(vinyl alcohol), PVA, chains in dilute solutions of a hydrated inorganic IL phase change material (PCM), lithium nitrate trihydrate (LNH). This solvent has an extremely high concentration of inorganic ions (≈18 M) with a low concentration of water molecules largely forming solvation shells of Li+ and NO3- ions, as shown using ATR-FTIR spectroscopy. Diffusion and hydrodynamic size of PVA chains of different molecular weights in this unusual solvent were studied using fluorescence correlation spectroscopy (FCS). A higher scaling exponent obtained from the molecular weight dependences of the diffusion coefficients of PVA chains as well as a lower overlap concentration (c*) of PVA in LNH solutions as measured by FCS suggest an expansion of the polymer coils in this solvent. We argue that enhanced solubility of PVA in LNH solutions is likely a result of increased rigidification of polymer chains due to the binding of solvated Li+ ions, which is demonstrated using 7Li NMR spectroscopy. We believe that an understanding of solvation and ion-binding capability can offer crucial insight into designing polymer-based shape stabilization matrices for inorganic PCMs.

Hydrogen-Bonded, Mechanically Strong Nanofibers with Tunable Antioxidant Activity.

We report on mechanically strong, water-insoluble hydrogen-bonded nanofiber mats composed of a hydrophilic polymer and a natural polyphenol that exhibit prolonged antioxidant activity. The high performance of fibrous mats resulted from the formation of a network of hydrogen bonds between a low-molecular-weight polyphenol (tannic acid, TA) and a water-soluble polymer (polyvinylpyrrolidone, PVP) and could be precisely controlled by the TA-to-PVP ratio. Dramatic enhancement (5- to 10-fold) in tensile strength, toughness, and Young's moduli of the PVP/TA fiber mats (as compared to those of pristine PVP fibers) was achieved at the maximum density of hydrogen bonds, which occurred at ∼0.2-0.4 molar fractions of TA. The formation of hydrogen bonds was confirmed by an increase in the glass-transition temperature of the polymer after binding with TA. When exposed to water, the fibers exhibited composition- and pH-dependent stabilities, with the TA-enriched fibers fully preserving their integrity in acidic and neutral media. Importantly, the fiber mats exhibited strong antioxidant activity with dual (burst and prolonged) activity profiles, which could be controlled via fiber composition, a feature useful for controlling radical-scavenging rates in environmental and biological applications.

Ocean Salinity Sensing Using Long-Period Fiber Gratings Functionalized with Layer-by-Layer Hydrogels.

Rapid, accurate, and real-time measurements of ocean salinity are of great importance for a host of scientific, commercial, and defense applications. We demonstrate a highly sensitive, fast-responding fiber-optic salinity sensor that integrates long-period fiber gratings (LPFGs) with ionic strength-responsive hydrogel. The submicron-thick hydrogel was synthesized via layer-by-layer electrostatic assembly of partially quaternized poly(4-vinylpyridine) (qP4VP) and poly(acrylic acid), followed by chemical cross-linking. Spectroscopic ellipsometry measurement of a hydrogel made of 37% quaternized qP4VP showed robust and reversible swelling/deswelling in solutions with salt concentrations ranging from 0.4 to 0.8 M (22.8-44.7 g/kg) around pH 8.1. The swelling/deswelling process induced large changes in the refractive index of the hydrogel, leading to resultant shift in the resonance wavelength (RW) of LPFGs. The salinity-dependent optical response of the hydrogel-coated LPFGs is in good agreement with ellipsometry measurement. LPFGs coated with the hydrogel exhibited a sensitivity of 7 nm RW shift/M (125.5 pm/‰) with a measurement time less than 5 s. The shift in the resonance wavelength correlated linearly with salt concentration, making quantification of measured salinity straightforward.

New Family of Water-Soluble Sulfo-Fluoro Polyphosphazenes and Their Assembly within Hemocompatible Nanocoatings.

In this work, novel sulfo-fluoro polyphosphazenes (PPzs) were synthesized via macromolecular substitution of polydichlorophosphazene utilizing "non-covalent protection" methodology by converting acid functionalities into hydrophobic alkylammonium salts. Resulting PPzs showed excellent solubility in aqueous solutions over a broad pH range and contained ∼25% sulfo- groups and 20% either trifluoroethoxy- (FESP) or trifluoromethylphenoxy- (FPSP) side groups, as determined by NMR spectroscopy. Their polyelectrolyte behavior was evaluated by binding with an oppositely charged polyion, branched polyethylenimine (PEI), which resulted in the formation of interpolymer complexes as shown by dynamic light scattering (DLS). Contrary to a sulfonated, nonfluorinated PPz homopolymer (SP), fluorinated macromolecules effectively bound human serum albumin (HSA) as revealed by dynamic light scattering and asymmetric flow field flow fractionation (AF4) studies. Moreover, FESP and FPSP both displayed low hemolytic activity as evaluated in solution using porcine red blood cells. Using the layer-by-layer (LbL) technique, FESP and FPSP were assembled into nanocoatings with PEI. Both fluorinated and nonfluorinated sulfo PPzs showed linear growth with PEI because of strong ionic pairing between sulfo and amino groups. However, films of fluorinated PPzs displayed higher hydrophobicity, lower swelling, and improved stability in high ionic strength environment when compared to coatings formed by a sulfonated, nonfluorinated SP, or a carbon-chain polymer poly(styrene sulfonic acid). Hemocompatibility of FESP and FPSP nanofilms was demonstrated in vitro using whole rabbit blood hemolysis tests, which showed less than 1% hemolysis. Altogether, the present study introduces a new class of hemocompatible, sulfo-fluoropolymers that shows promise for life science applications.

Functional Surfaces through Controlled Assemblies of Upper Critical Solution Temperature Block and Star Copolymers.

Endowing surfaces with multiple advanced functionalities, such as temperature-controlled swelling or the triggered release of functional small molecules, is attractive for a large variety of applications ranging from smart textiles to advanced biomedical applications. This Invited Feature Article summarizes recent advances in the development of upper critical solution temperature (UCST) behavior of copolymers in aqueous solutions and compares the fundamental differences between lower critical solution temperature (LCST) and UCST transitions. The effect of polymer chemistry and architecture on UCST transitions is discussed for block copolymer micelles (BCMs) and star polymers in solution and assembled at surfaces. The inclusion of such nanocontainers (i.e., BCMs and star polymers) in layer-by-layer (LbL) coatings and how to control their responsive behavior through deposition conditions and binding partners is explored. Finally, the inclusion and temperature-triggered release of functional small molecules is explored for nanocontainers in LbL coatings. Taken together, UCST nanocontainers containing LbL films are promising building blocks for the development of new generations of practical, functional surface coatings.