Synthesis of TiO2 hollow nanofibers by co-axial electrospinning and its superior lithium storage capability in full-cell assembly with olivine phosphate.

We report the formation and extraordinary Li-storage properties of TiO2 hollow nanofibers by co-axial electrospinning in both the half-cell and full-cell configurations. Li-insertion properties are first evaluated as anodes in the half-cell configuration (Li/TiO2 hollow nanofibers) and we found that reversible insertion of ~0.45 moles is feasible at a current density of 100 mA g(-1). The half-cell displayed a good cyclability and retained 84% of its initial reversible capacity after 300 galvanostatic cycles. The full-cell is fabricated with a commercially available olivine phase LiFePO4 cathode under optimized mass loading. The LiFePO4/TiO2 hollow nanofiber cell delivered a reversible capacity of 103 mA h g(-1) at a current density of 100 mA g(-1) with an operating potential of ~1.4 V. Excellent cyclability is noted for the full-cell configuration, irrespective of the applied current densities, and it retained 88% of reversible capacity after 300 cycles in ambient conditions at a current density of 100 mA g(-1).

Nanostructured α-Fe2O3 platform for the electrochemical sensing of folic acid.

α-Fe(2)O(3) nanofibers are synthesized by a simple and efficient electrospinning method and the selective determination of folic acid (FA) is demonstrated in the presence of an important physiological interferent, ascorbic acid (AA), using the α-Fe(2)O(3) nanofiber modified glassy carbon (GC) electrode at physiological pH. Bare GC electrode fails to determine the concentration of FA in the presence of a higher concentration of AA due to the surface fouling caused by the oxidized products of AA and FA. However, modification with α-Fe(2)O(3) nanofibers not only separates the voltammetric signals of AA and FA by 420 mV between AA and FA, but also enhances higher oxidation current. The amperometric current response is linearly dependent on FA concentration in the range of 60-60,000 nM, and the α-Fe(2)O(3) nanofiber modified electrode displayed an excellent sensitivity for FA detection with an experimental detection limit of 60 nM (1.12 × 10(-10) M (S/N = 3)). Furthermore, the α-Fe(2)O(3) nanofiber modified electrode showed an admirable selectivity towards the determination of FA even in the presence of a 1000-fold excess of AA and other common interferents. This modified electrode has been successfully applied for determination of FA in human blood serum samples.

Enhanced super-hydrophobic and switching behavior of ZnO nanostructured surfaces prepared by simple solution--immersion successive ionic layer adsorption and reaction process.

A simple and cost-effective successive ionic layer adsorption and reaction (SILAR) method was adopted to fabricate hydrophobic ZnO nanostructured surfaces on transparent indium-tin oxide (ITO), glass and polyethylene terephthalate (PET) substrates. ZnO films deposited on different substrates show hierarchical structures like spindle, flower and spherical shape with diameters ranging from 30 to 300 nm. The photo-induced switching behaviors of ZnO film surfaces between hydrophobic and hydrophilic states were examined by water contact angle and X-ray photoelectron spectroscopy (XPS) analysis. ZnO nanostructured films had contact angles of ~140° and 160°±2 on glass and PET substrates, respectively, exhibiting hydrophobic behavior without any surface modification or treatment. Upon exposure to ultraviolet (UV) illumination, the films showed hydrophilic behavior (contact angle: 15°±2), which upon low thermal stimuli revert back to its original hydrophobic nature. Such reversible and repeatable switching behaviors were observed upon cyclical exposure to ultraviolet radiation. These biomimetic ZnO surfaces exhibit good anti-reflective properties with lower reflectance of 9% for PET substrates. Thus, the present work is significant in terms of its potential application in switching devices, solar coatings and self-cleaning smart windows.

Kinetics of the removal of mono-chlorobenzene vapour from waste gases using a trickle bed air biofilter.

The performance of a trickle bed air biofilter (TBAB) in the removal of mono-chlorobenzene (MCB) was evaluated in concentrations varying from 0.133 to 7.187 g m(-3) and at empty bed residence time (EBRT) varying from 37.7 to 188.52 s. More than 90% removal efficiency in the trickle bed air biofilter was achieved for the inlet MCB concentration up to 1.069 g m(-3) and EBRT less than 94.26 s. The trickle bed air biofilter was constructed with coal packing material, inoculated with a mixed consortium of activated sludge obtained from sewage treatment plant. The continuous performance of the removal of MCB in the trickle bed air biofilter was monitored for various gas concentrations, gas flow rates, and empty bed residence time. The experiment was conducted for a period of 75 days. The trickle bed air biofilter degrading MCB with an average elimination capacity of 80 g m(-3) h(-1) was obtained. The effect of starvation was also studied. After starvation period of 8 days, the degradation was low but recovered within a short period of time. Using macrokinetic determination method, the Michaelis-Menten kinetic constant K(m) and maximum reaction rate, r(max) evaluated as 0.121 g m(-3) s(-1) and 7.45 g m(-3), respectively.