Downflow sponge biofilm reactors for polluted raw water treatment: Performance optimisation, kinetics, and microbial community.

Water outages caused by elevated ammonium (NH4+-N) levels are a prevalent problem faced by conventional raw water treatment plants in developing countries. A treatment solution requires a short hydraulic retention time (HRT) to overcome nitrification rate limitation in oligotrophic conditions. In this study, the performance of polluted raw water treatment using a green downflow sponge biofilm (DSB) technology was evaluated. We operated two DSB reactors, DSB-1 and DSB-2 under different NH4+-N concentration ranges (DSB-1: 3.2-5.0 mg L-1; DSB-2: 1.7-2.6 mg L-1) over 360 days and monitored their performance under short HRT (60 min, 30 min, 20 min, and 15 min). The experimental results revealed vertical segregation of organic removal in the upper reactor depths and nitrification in the lower depths. Under the shortest HRT of 15 min, both DSB reactors achieved stable NH4+-N and chemical oxygen demand removal (≥95%) and produced minimal effluent nitrite (NO2--N). DSB system could facilitate complete NH4+-N oxidation to nitrate (NO3--N) without external aeration energy requirement. The 16S rRNA sequencing data revealed that nitrifying bacteria Nitrosomonas and Nitrospira in the reactor were stratified. Putative comammox bacteria with high ammonia affinity was successfully enriched in DSB-2 operating at a lower NH4+-N loading rate, which is advantageous in oligotrophic treatment. This study suggests that a high hydraulic rate DSB system with efficient ammonia removal could incorporate ammonia treatment capability into polluted raw water treatment process and ensure safe water supply in many developing countries.

Quantitative detection and reduction of potentially pathogenic bacterial groups of Aeromonas, Arcobacter, Klebsiella pneumoniae species complex, and Mycobacterium in wastewater treatment facilities.

Water quality parameters influence the abundance of pathogenic bacteria. The genera Aeromonas, Arcobacter, Klebsiella, and Mycobacterium are among the representative pathogenic bacteria identified in wastewater. However, information on the correlations between water quality and the abundance of these bacteria, as well as their reduction rate in existing wastewater treatment facilities (WTFs), is lacking. Hence, this study aimed to determine the abundance and reduction rates of these bacterial groups in WTFs. Sixty-eight samples (34 influent and 34 non-disinfected, treated, effluent samples) were collected from nine WTFs in Japan and Thailand. 16S rRNA gene amplicon sequencing analysis revealed the presence of Aeromonas, Arcobacter, and Mycobacterium in all influent wastewater and treated effluent samples. Quantitative real-time polymerase chain reaction (qPCR) was used to quantify the abundance of Aeromonas, Arcobacter, Klebsiella pneumoniae species complex (KpSC), and Mycobacterium. The geometric mean abundances of Aeromonas, Arcobacter, KpSC, and Mycobacterium in the influent wastewater were 1.2 × 104-2.4 × 105, 1.0 × 105-4.5 × 106, 3.6 × 102-4.3 × 104, and 6.9 × 103-5.5 × 104 cells mL-1, respectively, and their average log reduction values were 0.77-2.57, 1.00-3.06, 1.35-3.11, and -0.67-1.57, respectively. Spearman's rank correlation coefficients indicated significant positive or negative correlations between the abundances of the potentially pathogenic bacterial groups and Escherichia coli as well as water quality parameters, namely, chemical/biochemical oxygen demand, total nitrogen, nitrate-nitrogen, nitrite-nitrogen, ammonium-nitrogen, suspended solids, volatile suspended solids, and oxidation-reduction potential. This study provides valuable information on the development and appropriate management of WTFs to produce safe, hygienic water.

A quantitative sequencing method using synthetic internal standards including functional and phylogenetic marker genes.

The method of spiking synthetic internal standard genes (ISGs) to samples for amplicon sequencing, generating sequences and converting absolute gene numbers from read counts has been used only for phylogenetic markers and has not been applied to functional markers. In this study, we developed ISGs, including gene sequences of the 16S rRNA, pmoA, encoding a subunit of particulate methane monooxygenase and amoA, encoding a subunit of ammonia monooxygenase. We added ISGs to the samples, amplified the target genes and performed amplicon sequencing. For the mock community, the copy numbers converted from read counts using ISGs were equivalent to those obtained by the quantitative real-time polymerase chain reaction (4.0 × 104 versus 4.1 × 104 and 3.0 × 103 versus 4.0 × 103 copies µL-DNA-1 for 16S rRNA and pmoA genes, respectively), but we also identified underestimation, possibly due to primer coverage (7.8 × 102 versus 3.7 × 103 µL-DNA-1 for amoA gene). We then applied this method to environmental samples and analysed phylogeny, functional diversity and absolute quantities. One Methylocystis population was most abundant in the sludge samples [16S rRNA gene (3.8 × 109 copies g-1 ) and the pmoA gene (2.3 × 109 copies g-1 )] and were potentially interrelated. This study demonstrates that ISG spiking is useful for evaluating sequencing data processing and quantifying functional markers.

Enhanced sulfide removal by gas stripping in a novel reactor for anaerobic wastewater treatment.

Removal of sulfide by gas stripping using biogas produced in an internal phase-separated reactor (IPSR) was evaluated during anaerobic treatment. The IPSR consisted of upper and lower segments with a gas-liquid partitioning (GLP) valve between the sections. Wastewater was fed to the upper segment in the first stage and then to the lower segment in the second stage. The GLP valve separated the liquid phase from the gaseous phase and supplied biogas from the lower segment to the upper segment. The IPSR and a control reactor were fed with synthetic wastewater and operated in parallel under an organic loading rate of 12 kg COD/(m3 day) at 35 °C. The sulfide concentration increased to 400-600 mg S/L, which is above the previously reported 50% inhibition level for methanogenic activity. The IPSR showed higher H2S removal performance than the control reactor and removed approximately twice the H2S as the control reactor at 400 mg S/L, indicating that it can be used for the stable treatment of wastewater containing high concentrations of sulfide.

Isolation and physiological properties of methanogenic archaea that degrade tetramethylammonium hydroxide.

Tetramethylammonium hydroxide (TMAH) is a known toxic chemical used in the photolithography process of semiconductor photoelectronic processes. Significant amounts of wastewater containing TMAH are discharged from electronic industries. It is therefore attractive to apply anaerobic treatment to industrial wastewater containing TMAH. In this study, a novel TMAH-degrading methanogenic archaeon was isolated from the granular sludge of a psychrophilic upflow anaerobic sludge blanket (UASB) reactor treating synthetic wastewater containing TMAH. Although the isolate (strain NY-STAYD) was phylogenetically related to Methanomethylovorans uponensis, it was the only isolated Methanomethylovorans strain capable of TMAH degradation. Strain NY-STAYD was capable of degrading methylamine compounds, similar to the previously isolated Methanomethylovorans spp. While the strain was able to grow at temperatures ranging from 15 to 37°C, the cell yield was higher at lower temperatures. The distribution of archaeal cells affiliated with the genus Methanomethylovorans in the original granular sludge was investigated by fluorescence in situ hybridization (FISH) using specific oligonucleotide probe targeting 16S rRNA. The results demonstrated that the TMAH-degrading cells associated with the genus Methanomethylovorans were not intermingled with other microorganisms but rather isolated on the granule's surface as a lone dominant archaeon. KEY POINTS: • A TMAH-degrading methanogenic Methanomethylovorans strain was isolated • This strain was the only known Methanomethylovorans isolate that can degrade TMAH • The highest cell yield of the isolate was obtained at psychrophilic conditions.

Metagenome-Assembled Genome Sequence of Marine Rhizobiaceae sp. Strain MnEN-MB40S, Obtained from Manganese-Oxidizing Enrichment Culture.

Here, we report a new metagenome-assembled genome (MAG) from a marine Rhizobiaceae species. The MnEN-MB40S genome was assembled from a manganese-oxidizing enrichment culture metagenome. A 4.1-Mb MAG comprising 26 contigs, with a GC content of 60.0%, was obtained. This MAG contributes to the genomic information regarding the family Rhizobiaceae.

Effects of sulfate concentration on anaerobic treatment of wastewater containing monoethanolamine using an up-flow anaerobic sludge blanket reactor.

Monoethanolamine (MEA), a toxic organic chemical, is widely used in industries and is found in their wastewater. Anaerobic MEA degradation is an appropriate strategy to reduce energy and cost for treatment. Industry wastewaters also contain sulfate, but information on the effects of sulfate on MEA degradation is limited. Here, an up-flow anaerobic sludge blanket (UASB) for MEA-containing wastewater treatment was operated under psychrophilic conditions (18-20 ºC) to investigate the effects of sulfate on the microbial characteristics of the retained sludge. To acclimatize the sludge, the proportion of MEA in the influent (containing sucrose, acetate, and propionate) was increased from 15% to 100% of total COD (1500 mg L-1); sulfate was then added to the influent. The COD removal efficiency remained above 95% despite the increase in MEA and sulfate. However, granular sludge disintegration was observed when sulfate was increased from 20 to 330 mg L-1. Batch tests revealed that propionate and acetate were produced as the metabolites of MEA degradation. In response to sulfate acclimation, methane-producing activities for propionate and hydrogen declined, while sulfate-reducing activities for MEA, propionate, and hydrogen increased. Accordingly, acclimation and changes in dominant microbial groups promoted the acetogenic reaction of propionate by sulfate reduction.

Manganese oxidation and prokaryotic community analysis in a polycaprolactone-packed aerated biofilm reactor operated under seawater conditions.

Biogenic manganese oxides (BioMnOx) have been receiving increasing attention for the removal of environmental contaminants and recovery of minor metals from water environments. However, the enrichment of heterotrophic Mn(II)-oxidizing microorganisms for BioMnOx production in the presence of fast-growing coexisting heterotrophs is challenging. In our previous work, we revealed that polycaprolactone (PCL), a biodegradable aliphatic polyester, can serve as an effective solid organic substrate to enrich Mn-oxidizing microbial communities under seawater conditions. However, marine BioMnOx-producing bioreactor systems utilizing PCL have not yet been established. Therefore, a laboratory-scale continuous-flow PCL-packed aerated biofilm (PAB) reactor was operated for 238 days to evaluate its feasibility for BioMnOx production under seawater conditions. After the start-up of the reactor, the average dissolved Mn removal rates of 0.4-2.3 mg/L/day, likely caused by Mn(II) oxidation, were confirmed under different influent dissolved Mn concentrations (2.5-14.0 mg/L on average) and theoretical hydraulic retention time (0.19-0.77 day) conditions. The 16S rRNA gene amplicon sequencing analysis suggested the presence of putative Mn(II)-oxidizing and PCL-degrading bacterial lineages in the reactor. Two highly dominant operational units (OTUs) in the packed PCL-associated biofilm were assigned to the genera Marinobacter and Pseudohoeflea, whereas the genus Lewinella and unclassified Alphaproteobacteria OTUs were highly dominant in the MnOx-containing black/dark brown precipitate-associated biofilm formed in the reactor. Excitation-emission matrix fluorescence spectroscopy analysis revealed the production of tyrosine- and tryptophane-like components, which may serve as soluble heterotrophic organic substrates in the reactor. Our findings indicate that PAB reactors are potentially applicable to BioMnOx production under seawater conditions.

Effect of formic acid inflow on microbial properties of the anaerobic granular sludge in a UASB reactor.

In the production of natural rubber, formate or acetate is added to the latex solution to coagulate the rubber; therefore, the wastewater contains high concentrations of organic acids, requiring the application of anaerobic treatment technology. In this study, a two-phase continuous flow experiment using a laboratory-scale upflow anaerobic sludge blanket (UASB) was conducted to investigate the influence of formate inflow on the microbial and physical characteristics of the retained granular sludge. In phase 1, acetate-based wastewater was used as feed, while in phase 2, formate-based wastewater was used as feed. In phase 1, the UASB exhibited high COD removal efficiency (97.2%); in addition, the retained sludge showed increased methane production from acetate and proliferation of acetate-utilizing Methanosaeta species. In phase 2, the UASB performed as well as phase 1, with 98.2% COD removal efficiency. Microbial community structure analysis confirmed that relatives of Methanobacterium formicicum present in the retained sludge were responsible for the degradation of formate in phase 2. However, decreased diameter and slight deterioration of granular sludge settleability were observed. In conclusion, formate inflow has low risk of interference with the process performance of the UASB, but it has negative effects on the physical properties of the granular sludge.

Water quality assessment and pollution threat to safe water supply for three river basins in Malaysia.

Pollution in raw water poses increasing threats to safe water supply in many developing countries. Therefore, a comprehensive water quality assessment is essential to provide various stakeholders the information to deal with this problem. This study applies chemometrics to interpret a recent 10-year water quality data from three major river basins (Selangor River basin, Langat River basin, and Klang River basin) frequented by water supply disruptions in Selangor, Malaysia. We present the application of selected chemometrics approaches, namely agglomerative hierarchical cluster analysis, principal component analysis, factor analysis and Man-Kendall trend analysis. The results showed three spatial groups of monitoring stations with similar land use practices and pollution characteristics. Besides spatial differences, periodic variations were observed when similar pollutants exhibited different pollution loads during rainy and dry periods. We found that nitrogen species, total suspended solids, and dissolved solids represented the major pollution loads in the studied basins. The results further confirmed a significant increasing trend in ammonia pollution. Our study demonstrates how ammonia pollutant is likely to pose a threat to water supply and highlights the vulnerability of Selangor's water resource system to water pollution. The results of this study could facilitate decision making towards more holistic strategies, specifically, incorporating ammonia treatment facilities into the conventional water treatment plant will help achieve smooth water supply operations.

Suppression of phosphorus release from eutrophic lake sediments by sediment microbial fuel cells.

Sediment microbial fuel cells (SMFCs) have served as an alternative technique to suppress phosphorus release from lake sediments to water bodies and thus mitigate eutrophication. However, the phosphorus regulation mechanism remains unclear. The purpose of this research was to understand the electrochemical influence of an SMFC on the phosphorus concentration in interstitial water. In this study, a lab-scale SMFC was applied to acetate-spiked sediments (ace+) and unspiked sediments (sed) with closed-circuit (CC)/open-circuit (OC) columns, and the circuitry was switched to investigate the relationship between electron transfer and phosphorus concentration. The dissolved total phosphorus (DTP) concentration in the sediment interstitial water in CC columns significantly decreased to below 0.1 mg/L, whereas the DTP in OC columns remained high for nine weeks. After switching the circuit, the DTP in OC→CC columns dropped but that in CC→OC columns increased within one week. At the end of the experimental period, the DTP concentrations in CC/sed, CC/ace+, OC/sed, and OC/ace+ columns were 0.10 ± 0.02, 0.03 ± 0.00, 0.82 ± 0.01, and 1.66 ± 0.12 mg/L, respectively. The respective estimated anode capacitances of those columns were 2.05 ± 0.49, 5.15 ± 0.14, 0.72 ± 0.19, and 0.71 ± 0.12 nF. We concluded that the phosphorus may have been electrochemically attracted and retained on the anode in the sediment because the adsorbed DTP contents and the increased anode capacitances were strongly correlated. Thus, SMFCs can be used for suppressing phosphorus release from eutrophic lake sediments.

Hexavalent Chromium Removal and Prokaryotic Community Analysis in Glass Column Reactor Packed with Aspen Wood as Solid Organic Substrate.

Microbial hexavalent chromium (Cr(VI)) reduction is a promising method for Cr(VI)-laden wastewater treatment. However, the soluble organic substrate required for heterotrophic microbial Cr(VI) reduction necessitates constant supervision, and an excessive supply of soluble organic substrate can result in deterioration of the quality of the effluent. In this study, we evaluated aspen wood, a low-cost lignocellulose biomass, as a solid organic substrate for heterotrophic Cr(VI) reduction. A laboratory-scale aspen wood-packed glass column reactor inoculated with activated sludge was operated for 148 days for evaluation. Following reactor operation, an effective average dissolved Cr(VI) removal rate of 0.75 mg L-1 h-1 was confirmed under an average dissolved Cr(VI) loading rate of 0.90 mg L-1 h-1. Subsequently, 16S ribosomal ribonucleic acid gene amplicon sequencing analysis revealed that the dominant prokaryotic operational taxonomic units detected in the reactor were associated with prokaryotic lineages with the capacity for lignocellulose biodegradation, Cr compound resistance, and Cr(VI) reduction. Proteobacteria and Chloroflexi were two major prokaryotic phyla in the reactor. Our data indicate that aspen wood is an effective solid organic substrate for the development of simplified, effective, and low-cost microbial Cr(VI)-removing reactors.

Sediment Microbiota in Response to Circuitry of Sediment Microbial Fuel Cells, Revealed by 16S rRNA Gene Amplicon Sequencing.

Information about sediment microbiota affected by sediment microbial fuel cells (SMFC) is limited. A laboratory-scale SMFC was applied to a eutrophic lake sediment under closed-circuit/open-circuit conditions. We analyzed the prokaryotes in the sediment adhering to the anode material. The archaeal family Methanoperedenaceae was a predominant group under closed-circuit conditions.

Detection of potentially pathogenic Arcobacter spp. in Bangkok canals and the Chao Phraya River.

The management of pathogenic bacteria in waterways is a public health issue. Here, we investigated the concentrations of potentially pathogenic bacteria, Arcobacter spp. and Campylobacter spp., and Escherichia coli, by quantifying species-specific genes in surface water samples from canals and the Chao Phraya River from June 2017 to June 2018 in Bangkok, Thailand. We assessed the relationship between the specific bacterial concentrations, water quality, and seasonal changes. Arcobacter spp. were detected at high density in all samples and showed seasonal fluctuations according to analyses based on 16S rDNA and the invasion gene ciaB. High levels of 16S rDNA and dut gene of E. coli were detected in the polluted drainage canals. A high correlation was observed between E. coli and chemical and biochemical oxygen demand (COD and BOD), suggesting that untreated domestic wastewater was the source of the E. coli. In contrast, Arcobacter spp. were detected with high density even in water samples with relatively low COD, suggesting that Arcobacter spp. are more likely than E. coli to survive in the water environment. The analysis of 16S rDNA and ciaB gene sequence analyses indicated that the Arcobacter spp. isolated from the drainage canals were A. butzleri and A. cryaerophilus.

Sequence-Specific Capture of Oligonucleotide Probes (SCOPE): a Simple and Rapid Microbial rRNA Quantification Method Using a Molecular Weight Cutoff Membrane.

A method named sequence-specific capture of oligonucleotide probes (SCOPE) was developed for quantification of microbial rRNA molecules in a multiplex manner. In this method, a molecular weight cutoff membrane (MWCOM) was used for the separation of fluorescence-labeled oligonucleotide probes hybridized with rRNA from free unhybridized probes. To demonstrate proof of concept, probes targeting bacteria or archaea at different taxonomic levels were prepared and were hybridized with rRNAs. The hybridization stringency was controlled by adjusting reaction temperature and urea concentration in the mixture. Then, the mixture was filtered through the MWCOM. The rRNA and hybridized probes collected on the MWCOM were recovered and quantified using a spectrophotometer and fluorospectrometer, respectively. The method showed high accuracy in detecting specific microbial rRNA in a defined nucleic acid mixture. Furthermore, the method was capable of simultaneous detection and quantification of multiple target rRNAs in a sample with sensitivity up to a single-base mismatch. The SCOPE method was tested and benchmarked against reverse transcription-quantitative PCR (RT-qPCR) for the quantification of Bacteria, Archaea, and some key methanogens in anaerobic sludge samples. It was observed that the SCOPE method produced more reliable and coherent results. Thus, the SCOPE method allows simple and rapid detection and quantification of target microbial rRNAs for environmental microbial population analysis without any need for enzymatic reactions. IMPORTANCE Microorganisms play integral roles in the Earth's ecosystem. Microbial populations and their activities significantly affect the global nutrient cycles. Quantification of key microorganisms provides important information that is required to understand their roles in the environment. Sequence-based analysis of microbial population is a powerful tool, but it provides information only on relative abundance of microorganisms. Hence, the development of a simpler and quick method for the quantification of microorganisms is necessary. To address the shortcomings of a variety of molecular methods reported so far, we developed a simple, rapid, accurate, and multiplexed microbial rRNA quantification method to evaluate the abundance of specific microbial populations in complex ecosystems. This method demonstrated high specificity, reproducibility, and applicability to such samples. The method is useful for quantitative detection of particular microbial members in the environment.

Differences in the isotopic signature of activated sludge in four types of advanced treatment processes at a municipal wastewater treatment plant.

The natural abundance of stable isotopes is a powerful tool for evaluating biological reactions and process conditions. However, there are few stable isotope studies on the wastewater treatment process. This study carried out the first investigation on variations in natural abundance of carbon and nitrogen stable isotope ratios (δ13C and δ15N) of activated sludge in four types of advanced treatment process (extended aeration activated sludge (EAAS), aerobic-anoxic-aerobic (A2O), recycled nitrification-denitrification (RND), and modified Bardenpho (MB)) at a municipal wastewater treatment plant. The δ13C and δ15N values of influent suspended solids settled in the primary sedimentation tank (i.e., primary sludge) ranged from -25.4‰ to -24.6‰ and 0.5‰-2.9‰, respectively, during monitoring periods. The δ13C values of the activated sludge were -24.6‰ to -23.6‰ (EAAS), -25.4‰ to -24.3‰ (A2O), -25.7‰ to -24.9‰ (RND), and -25.7‰ to -24.3‰ (MB). The δ13C values of the activated sludge were similar to those of influent suspended solids. However, the δ13C values of activated sludge in EAAS was significantly higher than in A2O, RND, and MB. Meanwhile, the δ15N values of activated sludge were obviously higher than influent suspended solids; 5.8‰-7.5‰ (EAAS), 6.6‰-8.1‰ (A2O), 5.5‰-7.5‰ (RND), and 5.3‰-7.6‰ (MB). Changes in δ13C and δ15N values of the activated sludge within the treatment system were also found. These findings indicate that changes in δ13C and δ15N values of the activated sludge rely on important function for biological wastewater treatment such as nitrification, denitrification, and methane oxidation through wastewater treatment over time.

Microbial properties of the granular sludge in a psychrophilic UASB reactor fed with electronics industry wastewater containing organic chemicals.

In this study, a lab-scale upflow anaerobic sludge blanket (UASB) reactor was applied to the treatment of artificial electronics industry wastewater containing tetramethylammonium-hydroxide (TMAH), monoethanolamine (MEA), and isopropyl-alcohol (IPA) in order to evaluate process performance and degradation properties. During 800 days of operation, 96% efficiency of chemical oxygen demand (COD) removal was stably achieved at an organic loading rate of 8.5 kgCOD/m3/day at 18-19 °C. MEA degradation, carried out by acid-forming eubacteria, was confirmed within a week. The physical properties of the retained granular sludge were degraded by feeding with TMAH wastewater, but maintained by feeding with MEA wastewater due to an accumulation of species from the genus Methanosaeta and family Geobacteraceae. Analysis of the microbial community structure via SEM and 16S rRNA genes showed a proliferation of Methanomethylovorans-like cells and Methanosaeta-like cells at the surface and in the core of the granular sludge with TMAH, MEA and IPA acclimation. Furthermore, a batch degradation experiment confirmed that process inhibition due to increasing chemical concentration was relatively stronger for TMAH than for MEA or IPA. Thus, controlling the TMAH concentration of the influent to below 1 gCOD/L will be important for the stable treatment of electronics industry wastewater by UASB technology.

Evaluation of stable isotope ratios (δ15N and δ18O) of nitrate in advanced sewage treatment processes: Isotopic signature in four process types.

Stable isotope ratios of nitrate are a powerful tool to evaluate aquatic environment stress from treated and untreated sewage. However, there is generally a lack of knowledge on the change in stable isotope ratios within wastewater treatment plants. We investigated nitrogen and oxygen stable isotope ratios (δ15N and δ18O) of nitrate in four types of advanced treatment processes operated in parallel; (A) extended aeration activated sludge, (B) anaerobic-anoxic-aerobic (A2O), (C) recycled nitrification-denitrification, and (D) modified Bardenpho. The results exhibited spatial variation of δ15N and δ18O for nitrate within the treatment steps. The changes in δ15N and δ18O may result from the reactor conditions (aerobic, anoxic, and anaerobic) and the order of these processes. As decreasing nitrate concentration in the anoxic stages, the δ15N/δ18O ratio for nitrate increased at a rate of 1.3 to 1.6 coupling with the reduction in the nitrate concentration in the anoxic stages. The δ15N and δ18O signatures were attributed to process performance in regard to nitrogen removal. In particular, the modified Bardenpho process has higher nitrogen removal efficiency over other processes, producing effluent with lower nitrate concentration and higher stable isotopes (δ15N: 23.6 to 25.5‰, δ18O: 2.8 to 4.5‰). We concluded that the stable isotope signatures mirrored the treatment efficiency and effluent characteristics.

Performance evaluation of a down-flow hanging sponge (DHS) reactor as a decentralized domestic wastewater treatment system in tropical regions.

In this study, a pilot-scale down-flow hanging sponge (DHS) reactor was operated in the community plant of Bangkok for the treatment of domestic wastewater (COD 285 mg/L, BOD 105 mg/L) collected by separate sewer to evaluate the reactor's feasibility as a decentralized treatment system. The DHS reactor was operated for 600 days at ambient temperatures of 25-30 °C, both with constant flow conditions and with fluctuating flow conditions that simulated wastewater discharge patterns of the community. The results indicate that under constant flow at an HRT of 5 h, the volumetric loading rates of 0.36 kgBOD/m3-sponge/day and 0.16 kgN/m3-sponge/day were the optimum operational conditions of the DHS reactor in order to satisfy the effluent discharge standards. The DHS achieved removal rates of 89, 95, 91 and 90% for COD, BOD, TSS and NH4-N. Under the fluctuating flow condition, improvement of denitrification was confirmed at volumetric loading rates of 0.50 kgBOD/m3-sponge/day and 0.18 kgN/m3-sponge/day. The fluctuating flow of wastewater positively affects retained sludge activities in terms of homogenizing sludge concentration and stimulating oxygen uptake rates. These results suggest that the DHS reactor can be applied as a decentralized treatment system for domestic wastewater with fluctuating flow rates in tropical regions.

Characterization of dissolved organic matter in wastewater during aerobic, anaerobic, and anoxic treatment processes by molecular size and fluorescence analyses.

Changes in the characteristics of dissolved organic matter (DOM: the dissolved fraction of natural organic matter) during a series of wastewater treatment plant (WWTP) processes were investigated by using a combination of molecular size analysis and excitation emission matrix (EEM) spectroscopy coupled with parallel factor analysis. The characteristics of DOM were compared following aerobic, anoxic, and anaerobic treatments. Three peaks at about 100,000 Da (high-molecular-size DOM, Peak 1) and about 900-1,100 Da (intermediate-molecular-size DOM, Peak 2; low-molecular-size DOM, Peak 3 as the shoulder of Peak 2) were observed in the distribution of total organic carbon molecular sizes in the influent of the WWTPs. In this study, five fluorescent components (C1 to C5) were identified in the EEM spectra. Molecular size analysis and molecular size fractionation revealed that the C3 (humic-like) and C5 (specific to sewage) fluorophores had intermediate or low molecular sizes. Comparison of the changes of the concentrations of dissolved organic carbon in each reaction tank and investigation of the removal selectivity of each treatment (aerobic, anaerobic, and anoxic) suggested that the heterogenous compounds present in DOM of the influent were homogenized into intermediate-molecular-size DOM with high hydrophobicity and aromaticity, or into C4 fluorophores (DOM-X), during anaerobic or anoxic treatment. DOM-X was able to be transformed or removed by aerobic treatment. The results suggested that introduction of aerobic treatment at the appropriate stage of wastewater treatment or inclusion of physical or chemical treatment should be an effective way to optimize DOM removal.