Solid phase characterization and transformation of illite mineral with gas-phase ammonia treatment.

In situ remediation applications of ammonia (NH3) gas have potential for sequestration of subsurface contamination. Ammonia gas injections initially increase the pore water pH leading to mineral dissolution followed by formation of secondary precipitates as the pH is neutralized. However, there is a lack of understanding of fundamental alteration processes due to NH3 treatment. In these batch studies, phyllosilicate minerals (illite and montmorillonite) were exposed to NH3 gas with subsequent aeration to simulate in situ remediation. Following treatments, solids were characterized using a variety of techniques, including X-ray diffraction, N2 adsorption-desorption analysis for surface area, Fourier transform infrared (FTIR) spectroscopy, nuclear magnetic resonance (NMR), and microscopy methods to investigate physicochemical transformations. Results indicate that, at high pH, the clays are altered as observed by differences in morphology and particle size via microscopy. However, the two clays interact differently with NH3. While montmorillonite interlayers collapsed due to intercalation, illite layers were unaffected as confirmed by FTIR analysis. Further, structural changes in silicate ([SiO4]n-) and aluminol (Al-OH) groups were identified by NMR and FTIR. This research showed that mineral alteration processes occur during and after NH3 gas treatment which may be used to remove radionuclides from the aqueous phase through sorption, co-precipitation, and coating with secondary phyllosilicate alteration products.

Hydrolysis of methylphosphonic anhydride solid to methylphosphonic acid probed by Raman and infrared reflectance spectroscopies.

Much is still unknown about the mechanisms and rates of environmental degradation of organophosphorous pesticides and agents. In this study we focus on the degradation of one organophosphorous compound, namely solid methylphosphonic anhydride [CH3P(O)OHOP(O)OHCH3, MPAN] and its rate of conversion to methylphosphonic acid (MPA) via heterogeneous hydrolysis. Pure MPAN was synthesized and loaded in open sample cups placed inside exposure chambers containing saturated salt solutions to control the relative humidity (RH). The reaction was monitored in the sample cup at various times using both infrared hemispherical reflectance (HRF) spectroscopy and Raman spectroscopy. Calibrated HRF and Raman spectra of both pure reagents as well as gravimetrically prepared mixtures were used to quantify the concentrations of MPAN and MPA throughout the reaction. Results show both HRF and Raman spectroscopies are convenient non-invasive methods for detection of solid chemicals as long as a large area is sampled to average out any spatial inhomogeneities that occur on the sample surface and minimal phase changes occur during the course of the reaction. The samples for the 54 and 75% RH studies showed significant deliquescence, and the liquid water had to be removed prior to measurement; this effect led to differences in the sample form, such that the calibration spectra were no longer valid for quantitative analysis using HRF spectroscopy. Raman spectroscopy, on the other hand, proved to be less sensitive to these effects and provided better estimation of the MPAN and MPA concentrations. The MPAN degradation rate displayed a very strong dependence on relative humidity: at room temperature the reaction showed 50% conversion of the MPAN in 761 ± 54 h at 33% RH, 33 ± 4 h at 43% RH, 17 ± 2 h at 54% RH and just 7 ± 1 h at 75% RH.

In situ precipitation of hydrous ferric oxide (HFO) for remediation of subsurface iodine contamination.

A practical approach for in situ hydrous ferric oxide (HFO) precipitation was developed for iodine immobilization under field-scale conditions at the Hanford Site. A series of 1D meter-long bench-top column experiments packed with Hanford sediments was conducted with a single acidic ferric solution (0.1 M, pH = 1.5) injection. Because carbonate and clay minerals are widely present in sediments, self-pH buffering of the injected acidic ferric solution occurred due to mineral dissolution, leading to HFO precipitation under a neutral condition. Up to ~12 mg/g Fe as HFO successfully precipitated and evenly distributed in the column sediments, and the remobilization of the neoformed HFO precipitates was limited (≤ ~3.16 wt% after over 100 pore volumes (pv) of flushing). The transport of iodate (IO3-) in the HFO-amended sediments was strongly retarded through both adsorption and co-precipitation processes. However, reversible adsorption of iodine on HFO was observed, which might limit its application to slow-moving groundwater systems.

A review of the behavior of radioiodine in the subsurface at two DOE sites.

Multiple processes affect the fate of the radioactive isotope 129I in the environment. Primary categories of these processes include electron transfer reactions mediated by minerals and microbes, adsorption to sediments, interactions with organic matter, co-precipitation, and volatilization. A description of dominant biogeochemical processes is provided to describe the interrelationship of these processes and the associated iodine chemical species. The majority of the subsurface iodine fate and transport studies in the United States have been conducted at U.S. Department of Energy (DOE) sites where radioisotopes of iodine are present in the environment and stored waste. The DOE Hanford Site and Savannah River Site (SRS) are used to illustrate how the iodine species and dominant processes at a site are controlled by the prevailing site biogeochemical conditions. These sites differ in terms of climate (arid vs. sub-tropical), major geochemical parameters (e.g., pH ~7.5 vs. 4), and mineralogy (carbonate vs. Fe/Al oxide dominated). The iodine speciation and dominant processes at a site also have implications for selection and implementation of suitable remedy approaches for 129I.

Identification of Uranium Minerals in Natural U-Bearing Rocks Using Infrared Reflectance Spectroscopy.

The identification of minerals, including uranium-bearing species, is often a labor-intensive process using X-ray diffraction (XRD), fluorescence, or other solid-phase or wet chemical techniques. While handheld XRD and fluorescence instruments can aid in field applications, handheld infrared (IR) reflectance spectrometers can now also be used in industrial or field environments, with rapid, nondestructive identification possible via analysis of the solid's reflectance spectrum providing information not found in other techniques. In this paper, we report the use of laboratory methods that measure the IR hemispherical reflectance of solids using an integrating sphere and have applied it to the identification of mineral mixtures (i.e., rocks), with widely varying percentages of uranium mineral content. We then apply classical least squares (CLS) and multivariate curve resolution (MCR) methods to better discriminate the minerals (along with two pure uranium chemicals U3O8 and UO2) against many common natural and anthropogenic background materials (e.g., silica sand, asphalt, calcite, K-feldspar) with good success. Ground truth as to mineral content was attained primarily by XRD. Identification is facile and specific, both for samples that are pure or are partially composed of uranium (e.g., boltwoodite, tyuyamunite, etc.) or non-uranium minerals. The characteristic IR bands generate unique (or class-specific) bands, typically arising from similar chemical moieties or functional groups in the minerals: uranyls, phosphates, silicates, etc. In some cases, the chemical groups that provide spectral discrimination in the longwave IR reflectance by generating upward-going (reststrahlen) bands can provide discrimination in the midwave and shortwave IR via downward-going absorption features, i.e., weaker overtone or combination bands arising from the same chemical moieties.

Desorption behavior of carbon tetrachloride and chloroform in contaminated low organic carbon aquifer sediments.

Slow release behavior of carbon tetrachloride (CCl(4)) and chloroform (CHCl(3)) in low organic carbon (<0.1%) deep aquifer sediments was quantified by 1-D column desorption studies with intact cores. The compounds had been in contact with the sediments for 30years. Comparison of the CCl(4) distribution coefficient (K(d)) from this study with those from short contact time experiments suggested that CCl(4)K(d)'s calculated from site contaminated sediments of long contact time are likely a factor of 10 or more higher than those calculated from short contact-time lab experiments. A significant portion of the CHCl(3) mass (55% to more than 90%) was resistant to aqueous desorption in sediments with clay contents ranging from 2.0% to 36.7% and organic carbon content ranging from 0.017% to 0.088%. In contrast, CCl(4) showed greatest mass retention (31% or more) only in the highest clay and organic carbon content sediment. Relatively easy solvent extraction of the residual masses of CCl(4) and CHCl(3) from the sediments indicated the compounds were not permanently sequestered. Tracer breakthrough in columns was well behaved, indicating interparticle diffusion was not causing the slow release behavior. Diffusion out of intraparticle pores is suggested to be the main process governing the observed behavior although, diffusion out of natural organic matter cannot be ruled out as a potential contributing factor. The half-life for release of the slow fraction of CHCl(3) mass from sediments was estimated to be in the range of weeks (100h) to months (1100h). Neither CCl(4) or CHCl(3) were detected at measurable levels in the column effluent of one of the sediments even though a significant mass fraction of CHCl(3) was found present on the sediment following desorption suggesting that our estimate of hundreds to thousands of hours for complete release of CHCl(3) masses from such sediment is conservative.

Biotic and abiotic degradation of CL-20 and RDX in soils.

The caged cyclic nitramine 2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane (CL-20) is a new explosive that has the potential to replace existing military explosives, but little is known about its environmental toxicity, transport, and fate. We quantified and compared the aerobic environmental fate of CL-20 to the widely used cyclic nitramine explosive hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) in surface and subsurface soil microcosms. Soil-free controls and biologically attenuated soil controls were used to separate abiotic processes from biologically mediated processes. Both abiotic and biological processes significantly degraded CL-20 in all soils examined. Apparent abiotic, first-order degradation rates (k) for CL-20 were not significantly different between soil-free controls (0.018 < k < 0.030 d(-1)) and biologically attenuated soil controls (0.003 < k < 0.277 d(-1)). The addition of glucose to biologically active soil microcosms significantly increased CL-20 degradation rates (0.068 < k < 1.22 d(-1)). Extents of mineralization of (14)C-CL-20 to (14)CO(2) in biologically active soil microcosms were 41.1 to 55.7%, indicating that the CL-20 cage was broken, since all carbons are part of the heterocyclic cage. Under aerobic conditions, abiotic degradation rates of RDX were generally slower (0 < k < 0.032 d(-1)) than abiotic CL-20 degradation rates. In biologically active soil microcosms amended with glucose aerobic RDX degradation rates varied between 0.010 and 0.474 d(-1). Biodegradation was a key factor in determining the environmental fate of RDX, while a combination of biotic and abiotic processes was important with CL-20. Our data suggest that CL-20 should be less recalcitrant than RDX in aerobic soils.

Oxidative remobilization of biogenic uranium(IV) precipitates: effects of iron(II) and pH.

The oxidative remobilization of uranium from biogenic U(IV) precipitates was investigated in bioreduced sediment suspensions in contact with atmospheric O2 with an emphasis on the influence of Fe(II) and pH on the rate and extent of U release from the solid to the aqueous phase. The sediment was collected from the U.S. Department of Energy Field Research Center (FRC) site at Oak Ridge, Tennessee. Biogenic U(IV) precipitates and bioreduced sediment were generated through anaerobic incubation with a dissimilatory metal reducing bacterium Shewanella putrefaciens strain CN32. The oxidative remobilization of freshly prepared and 1-yr aged biogenic U(IV) was conducted in 0.1 mol/L NaNO3 electrolyte with variable pH and Fe(II) concentrations. Biogenic U(IV)O2(s) was released into the aqueous phase with the highest rate and extent at pH 4 and 9, while the U remobilization was the lowest at circumneutral pH. Increasing Fe(II) significantly decreased U remobilization to the aqueous phase. From 70 to 100% of the U in the sediments used in all the tests was extractable at the experiment termination (41 d) with a bicarbonate solution (0.2 mol/L), indicating that biogenic U(IV) was oxidized regardless of Fe(II) concentration and pH. Sorption experiments and modeling calculations indicated that the inhibitive effect of Fe(II) on U(IV) oxidative remobilization was consistent with the Fe(III) oxide precipitation and U(VI) sorption to this secondary phase.

Aluminum effect on dissolution and precipitation under hyperalkaline conditions: I. Liquid phase transformations.

Substantial amounts of self-boiling, Al-rich, hyperalkaline, and saline high-level waste fluids (HLWF) were deposited to the vadose zone at the Hanford Site, in Washington State. The objective of this study was to investigate the effects of similar fluids on the extent of dissolution and precipitation in the sediments. Metal- and glass-free systems were used to conduct batch experiments at 323 K under CO2 and O2 free conditions. Base-induced dissolution of the soil minerals was rapid in the first 48 h as indicated by immediate releases of Si and Fe into the soil solution. Potassium release lagged behind and dissolution of K-bearing minerals (mica and K-feldspar) proceeded faster only after 2 to 3 d of the experiment. Silicon and Fe release exhibited high dependence on aqueous [Al] (rate orders <-1), because Al decreased free OH concentration in the contact solution and probably inhibited soil mineral dissolution. Initial K release exhibited low dependence on [Al] (fractional rate orders). Initial dissolution rates calculated based on Si release varied with aqueous [Al] from 29.47 to 4.35 x 10(-12) mol m(-2) s(-1). Aluminum participated in the formation of the secondary phases (precipitation rates of 10(-8) mol s(-1)) but the overall precipitation rate of alumino-silicate secondary phases was probably controlled by aqueous [Si] (rates of 10(-9), and rate constants between 0.0054 and 0.0084 h(-1)). The changes in the soil solution chemistry (release of K, Si, Fe, and other elements) may play a significant role in the fate of radionuclides and contaminants like Cs, Sr, Cr, and U in the Hanford sediments.

Aluminum effect on dissolution and precipitation under hyperalkaline conditions: II. Solid phase transformations.

The high-level radioactive, Al-rich, concentrated alkaline and saline waste fluids stored in underground tanks have accidentally leaked into the vadose zone at the Hanford Site in Washington State. In addition to dissolution, precipitation is likely to occur when these waste fluids contact the sediments. The objective of this study was to investigate the solid phase transformations caused by dissolution and precipitation in the sediments treated with solutions similar to the waste fluids. Batch experiments at 323 K were conducted in metal- and glass-free systems under CO2 and O2 free conditions. Results from X-ray diffraction (XRD), quantitative X-ray diffraction (QXRD), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and energy dispersive X-ray fluorescence spectroscopy (EDXRF) indicated that significant solid phase transformations occurred in the sediments contacted with Al-rich, hyperalkaline, and saline solutions. The XRD and QXRD analyses confirmed that smectite and most likely biotite underwent dissolution. The SEM and the qualitative EDS analyses confirmed the formation of alumino-silicates in the groups of cancrinite and probably sodalite. The morphology of the alumino-silicates secondary phases changed in response to changes in the Si/Al aqueous molar ratio. The transformations in the sediments triggered by dissolution (weathering of soil minerals) and precipitation (formation of secondary phases with high specific surface area and probably high sorption capacities) may play a significant role in the immobilization and ultimate fate of radionuclides and contaminants such as Cs, Sr, and U in the Hanford vadose zone.

Effect of coupled dissolution and redox reactions on Cr(VI)aq attenuation during transport in the sediments under hyperalkaline conditions.

Aluminum-rich, hyperalkaline (pH > 13.5) and saline high-level nuclear waste (HLW) fluids at elevated temperatures (>50 degrees C), that possibly contained as much as 0.41 mol L(-1) Cr(VI), accidentally leaked to the sediments at the Hanford Site, WA. These extreme conditions promote base-induced dissolution of soil minerals which may affect Cr(VI)aq mobility. Our objective was to investigate Cr(VI)aq transport in sediments leached with HLW simulants at 50 degrees C, under CO2 and O2 free conditions. Results demonstrated that Cr(VI)aq fate was closely related to dissolution, and Cr(VI)aq mass loss was negligible in the first pore volumes but increased significantly thereafter. Similar to dissolution, Cr(VI)aq attenuation increased with increasing fluid residence time and NaOH concentration but decreased with Al concentrations in the leaching solutions. Aqueous Cr(VI) removal rate half-lives varied from 1.2 to 230 h with the fastest at the highest base concentration, lowest Al concentration, greatest reaction time, and lowest Cr(VI) concentration in the leaching solution. The rate of Cr(VI) removal (normalized to 1 kg of solution) varied from 0.83 x 10(-9) (+/-0.44 x 10(-9)) to 9.16 x 10(-9) (+/-1.10 x 10(-9)) mol s(-1). The predominant mechanism responsible for removing Cr(VI) from the aqueous phase appears to be homogeneous Cr(VI) reduction to Cr(III) by Fe(II) released during mineral dissolution. Cr(VI)aq removal was time-limited probably because it was controlled by the rate of Fe(II) release into the soil solution upon mineral dissolution, which was also a time-limited process, and other processes that may act to lower Fe(II)aq activity.