Using of sonochemically prepared SbSI for electrospun nanofibers.

A novel polymeric, polyacrylonitrile (PAN) nanofibers containing ferroelectric and semiconducting antimony sulfoiodide (SbSI) have been made by electrospinning. SbSI nanowires, used as the filler, have been prepared sonochemically from antimony sulphide (Sb2S3) and antimony tri-iodide (SbI3) for the first time. Nanocrystalline SbSI has been fabricated in ethanol under ultrasonic irradiation (20kHz, 565W/cm2) at 323K within 2h. The products have been characterized by using techniques such as powder X-ray diffraction, scanning electron microscopy, energy dispersive X-ray analysis, high-resolution transmission electron microscopy, selected area electron diffraction and optical diffuse reflection as well as transmission spectroscopy. The good quality of the nanocrystals and their dispersion in the nanofiber's volume is important because this material is attractive for nanogenerators due to its ferroelectric and piezoelectric properties. The amplitude of the voltage pulse, generated under shock pressure of 3.0MPa, has reached 180V in the prototype PAN/SbSI piezoelectric nanogenerator. The peak output voltage of about 0.2V was measured in bending/releasing conditions with the deformation frequency of 1Hz.

Sonochemical growth of antimony selenoiodide in multiwalled carbon nanotube.

This paper presents, for the first time, the nanocrystalline, semiconducting antimony selenoiodide (SbSeI) grown in multi-walled carbon nanotubes (CNTs). It was prepared sonochemically using elemental Sb, Se, and I in the presence of ethanol under ultrasonic irradiation (35 kHz, 2.6 W/cm2) at 323 K for 3 h. The CNTs filled with SbSeI were characterized by using techniques such as powder X-ray diffraction, scanning electron microscopy, energy dispersive X-ray analysis, high-resolution transmission electron microscopy, selected area electron diffraction, and optical diffuse reflection spectroscopy. These investigations exhibit that the SbSeI filling the CNTs is single crystalline in nature and in the form of nanowires. It has indirect allowed energy band gap EgIf=1.61(6) eV.

Using of sonochemically prepared components for vapor phase growing of SbI3.3S8.

The using of sonochemically prepared components for growth of SbI(3).3S(8) single crystals from the vapor phase is presented for the first time. The good optical quality of the obtained crystals is important because this material is valuable for optoelectronics due to its non-linear optical properties. The products were characterized by using techniques such as X-ray crystallography, powder X-ray diffraction, scanning electron microscopy, energy dispersive X-ray analysis, high-resolution transmission electron microscopy, selected area electron diffraction, optical diffuse reflection spectroscopy and optical transmittance spectroscopy. The direct and indirect forbidden energy gaps of SbI(3).3S(8) illuminated with plane polarized light with electric field parallel and perpendicular to the c-axis of the crystal have been determined. The second harmonic generation of light in the grown crystals was observed.

Sonochemical preparation of SbS(1-x)Se(x)I nanowires.

A sonochemical method for direct preparation of nanowires of SbS(1-x)Se(x)I solid solution has been established. The SbS(1-x)Se(x)I gel was synthesized using elemental Sb, S, Se and I in the presence of ethanol under ultrasonic irradiation (35kHz, 2W/cm(2)) at 50 degrees C for 2h. The product was characterized by using techniques such as powder X-ray diffraction, scanning electron microscopy, high-resolution transmission electron microscopy, energy dispersive X-ray analysis, selected area electron diffraction, and optical diffuse reflection spectroscopy. The SEM and HRTEM investigations exhibit that the as-prepared samples are made up of large quantity nanowires with lateral dimensions of about 10-50nm and lengths reaching up to several micrometers and single-crystalline in nature. The increase of molar composition of Se affects linear decrease of the indirect forbidden optical energy gap as well as the distance between (121) planes of the SbS(1-x)Se(x)I nanowires.

Sonochemical preparation of antimony subiodide.

The substantiated isolation of the antimony subiodide (Sb(3)I) is presented for the first time. It has been prepared using elemental Sb and I in ethanol under ultrasonic irradiation at 323 K. Its composition was characterized using X-ray photoelectron spectroscopy (XPS) and energy dispersive X-ray analysis (EDAX). The scanning electron microscopy (SEM) and high-resolution transmission electron microscopy (HRTEM) investigations exhibit that the samples are made up of large quantity of nanoparticles with diameters smaller than 20 nm and single crystalline in nature. The interplanar spacings in Sb(3)I that have been determined using powder X-ray diffraction (XRD), selected area electron diffraction (SAED) and HRTEM are very similar. Surprisingly, the registered XRD patterns are identical to the one reported earlier for Sb(4)O(5)I(2).

Determination of energy band gap of nanocrystalline SbSI using diffuse reflectance spectroscopy.

Twelve methods of determining energy band gap (E(g)) of semiconductors using diffuse reflectance spectroscopy have been applied in investigations of sonochemically produced antimony sulfoiodide (SbSI) consisting of nanowires. It has been proved that the best method of determining E(g) is based on simultaneous fitting of many mechanisms of absorption to the spectral dependence of Kubelka-Munk function evaluated from the diffuse reflectance data. It allows determining the values of indirect forbidden E(g), the Urbach energy, and the constant absorption/scattering of the examined semiconductor.

Sonochemical growth of antimony sulfoiodide in multiwalled carbon nanotube.

This paper presents for the first time the nanocrystalline, semiconducting ferroelectrics antimony sulfoiodide (SbSI) grown in multiwalled carbon nanotubes (CNTs). It was prepared sonochemically using elemental Sb, S and I in the presence of methanol under ultrasonic irradiation (35kHz, 2.6W/cm(2)) at 323K for 3h. The CNTs filled with SbSI were characterized by using techniques such as powder X-ray diffraction, scanning electron microscopy, energy dispersive X-ray analysis, high-resolution transmission electron microscopy, selected area electron diffraction, and optical diffuse reflection spectroscopy. These investigations exhibit that the SbSI filling the CNTs is single crystalline in nature and in the form of nanowires. It has indirect forbidden energy band gap E(gIf)=1.871(1)eV.

Influence of the solvent on ultrasonically produced SbSI nanowires.

The influence of the substitution of methanol in place of ethanol during the ultrasonic production of antimony sulfoiodide (SbSI) nanowires is presented. The new technology is faster and more efficient at temperatures greater than 314 K. The products were characterized by using techniques such as powder X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDXA), high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED), optical diffuse reflection spectroscopy (DRS) and IR spectroscopy. The coexistence of Pna2(1) (ferroelectric) and Pnam (paraelectric) phases at 298 K was observed in the SbSI nanowires produced in methanol. The methanol decomposes during the sonication or due to the adsorption process on SbSI nanowires.

Sonochemical preparation of SbSeI gel.

A novel sonochemical method for direct preparation of nanocrystalline antimony selenoiodide (SbSeI) has been established. The SbSeI gel was synthesized using elemental Sb, Se, and I in the presence of ethanol under ultrasonic irradiation (35 kHz, 2W/cm(2)) at 50 degrees C for 2h. The product was characterized by using techniques such as powder X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDAX), high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED), and optical diffuse reflection spectroscopy (DRS). The SEM and HRTEM investigations exhibit that the as-prepared samples are made up of large quantity nanowires with lateral dimensions of about 20-50 nm and lengths reaching up to several micrometers and single crystalline in nature.

Sonochemical preparation of SbSI gel.

A novel sonochemical method for direct preparation of nanocrystalline antimony sulfoiodide (SbSI) has been established. The SbSI gel was synthesized using elemental Sb, S and I in the presence of ethanol under ultrasonic irradiation (35 kHz, 2 W/cm2) at 50 degrees C for 2 h. The products were characterized by using techniques such as powder X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDAX), high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED), and optical diffuse reflection spectroscopy (DRS). The SEM and HRTEM investigations exhibit that the as-prepared samples are made up of large quantity nanowires with diameters of about 10-50 nm and lengths reaching up to several micrometers and single-crystalline in nature.