High-Performance Photoelectrochemical Water Oxidation with Phosphorus-Doped and Metal Phosphide Cocatalyst-Modified g-C3 N4 Formation Through Gas Treatment.

Graphitic carbon nitride (g-C3 N4 ) has been widely explored as a photocatalyst for water splitting. The anodic water oxidation reaction (WOR) remains a major obstacle for such processes, with issues such as low surface area of g-C3 N4 , poor light absorption, and low charge-transfer efficiency. In this work, such longtime concerns have been partially addressed with band gap and surface engineering of nanostructured graphitic carbon nitride (g-C3 N4 ). Specifically, surface area and charge-transfer efficiency are significantly enhanced through architecting g-C3 N4 on nanorod TiO2 to avoid aggregation of layered g-C3 N4 . Moreover, a simple phosphide gas treatment of TiO2 /g-C3 N4 configuration not only narrows the band gap of g-C3 N4 by 0.57 eV shifting it into visible range but also generates in situ a metal phosphide (M=Fe, Cu) water oxidation cocatalyst. This TiO2 /g-C3 N4 /FeP configuration significantly improves charge separation and transfer capability. As a result, our non-noble-metal photoelectrochemical system yields outstanding visible light (>420 nm) photocurrent: approximately 0.3 mA cm-2 at 1.23 V and 1.1 mA cm-2 at 2.0 V versus RHE, which is the highest for a g-C3 N4 -based photoanode. It is expected that the TiO2 /g-C3 N4 /FeP configuration synthesized by a simple phosphide gas treatment will provide new insight for producing robust g-C3 N4 for water oxidation.

Tubular morphology preservation and doping engineering of Sn/P-codoped hematite for photoelectrochemical water oxidation.

Tubular hematite with high-concentration, uniform doping is regarded as a promising material for photoelectrochemical water oxidation. However, the high-temperature annealing commonly used for activating doped hematite inevitably causes deformation of the tubular structure and an increase in the trap states. In the present work, Sn-doped tubular hematite on fluorine-doped tin oxide (FTO) is successfully obtained at 750 °C from a Sn-coated FeOOH tube precursor. Sn/P codoping, which is rarely considered for hematite, is also achieved via a gas phase reaction in phosphide atmosphere. The tubular morphology allows the dopant to diffuse from both the inner and outer surfaces, thus decreasing the doping profile in the radial direction. The even distribution of Sn and P synergetically increases the carrier density of hematite by one order of magnitude, which shortens the width of the depletion layer to ca. 2.3 nm (compared with 19.3 nm for the pristine sample) and leads to prolonged carrier lifetime and efficient charge separation. In addition, this codoping protocol does not introduce additional surface trap states, as evidenced by the increased charge injection efficiency and surface kinetic analysis using intensity modulated photocurrent spectroscopy (IMPS). As a result, the morphology- and doping-engineered hematite exhibits photocurrents of 0.9 mA cm-2 at 1.23 V and 3.8 mA cm-2 at 2.0 V vs. RHE under AM 1.5 G illumination (100 mW cm-2) in 1.0 M NaOH, representing 4.5-fold and 4.8-fold enhancements, respectively, compared with the photocurrents of undoped hematite. The present method is shown to be effective for preparing multi-element-doped hematite nanotubes and may find broad application in the development of other nanotubular photoelectrodes with or without doping for efficient and robust water oxidation.

Brand new 1D branched CuO nanowire arrays for efficient photoelectrochemical water reduction.

Developing high surface area nanostructured electrodes with fast charge separation is one of the main challenges for exploring cupric oxide (CuO)-based photocathodes in solar-driven hydrogen production applications. Herein, brand new 1D branched CuO nanowire arrays have been achieved on fluorine-doped tin oxide-coated glass (FTO) through a two-step wet chemical redox reaction. X-ray diffraction patterns, Raman spectra and X-ray photoelectron spectroscopy confirm the pure phase characteristic of the resulting branched CuO. In addition to the enlarged surface area of this advanced functional structure as compared with that of the 1D wire trunk, the charge injection and separation have been improved by rationally controlling the density of defects and size of branches. As a result, the optimized branched CuO exhibits photocurrent as high as 3.6 mA·cm-2 under AM 1.5G (100 mW·cm-2) illumination and 3.0 mA·cm-2 under visible light (λ > 420 nm) at 0.2 V vs. RHE in 0.5 M Na2SO4, which are 2.8- and 3.0-fold greater than those of 1D wire samples, respectively. In addition, the solution-processed approach established herein seems quite favourable for large-scale and low-cost manufacturing.

Fe2 PO5 -Encapsulated Reverse Energetic ZnO/Fe2 O3 Heterojunction Nanowire for Enhanced Photoelectrochemical Oxidation of Water.

Zinc oxide is regarded as a promising candidate for application in photoelectrochemical water oxidation due to its higher electron mobility. However, its instability under alkaline conditions limits its application in a practical setting. Herein, we demonstrate an easily achieved wet-chemical route to chemically stabilize ZnO nanowires (NWs) by protecting them with a thin layer Fe2 O3 shell. This shell, in which the thickness can be tuned by varying reaction times, forms an intact interface with ZnO NWs, thus protecting ZnO from corrosion in a basic solution. The reverse energetic heterojunction nanowires are subsequently activated by introducing an amorphous iron phosphate, which substantially suppressed surface recombination as a passivation layer and improved photoelectrochemical performance as a potential catalyst. Compared with pure ZnO NWs (0.4 mA cm-2 ), a maximal photocurrent of 1.0 mA cm-2 is achieved with ZnO/Fe2 O3 core-shell NWs and 2.3 mA cm-2 was achieved for the PH3 -treated NWs at 1.23 V versus RHE. The PH3 low-temperature treatment creates a dual function, passivation and catalyst layer (Fe2 PO5 ), examined by X-ray photoelectron spectroscopy, TEM, photoelectrochemical characterization, and impedance measurements. Such a nano-composition design offers great promise to improve the overall performance of the photoanode material.

A nanostructured hematite film prepared by a facile "top down" method for application in photoelectrochemistry.

To overcome tough conditions currently used for the preparation of nanostructured hematite films on a conducting substrate, a rational and easy method of chemical etching involving Fe3+ release and material growth in the presence of OH- has been developed. By carefully tuning the parameters influencing the morphologies of hematite, including the synthetic procedure, the concentration of etching solution, temperature, etching time and the morphology controlling surfactant, hematite films grown on iron foil with various morphologies (e.g. nanorod, nanowire, ultrathin nanoflake and cauliflower-like shape) have been achieved. In particular, it is found that F- is an effective surfactant to control the morphology as well as the crystallization process of hematite. Ultrathin nanoflakes having a minimized feature size exhibit the best photocurrent of 0.5 mA cm-2 (1.23 V vs. RHE, RHE is reversible hydrogen electrode) among the samples tested as a result of facilitated hole diffusion to the electrolyte and thus lowered carrier recombination. Compared with pristine hematite, a nearly tripled photocurrent is observed when H2O2 is added in the electrolyte as a hole scavenger, suggesting the presence of a charge injection barrier in the surface of samples. According to this, the strategy of Co2+ treatment is utilized and the improved photocurrent is seen, likely due to the improved water oxidation kinetics and surface state passivation. We believe that this convenient and economical method can be extended to the synthesis of other alkaline metal oxide nanomaterials as long as the redox potential of S2O82-/SO42- is higher than Mn+/M (M refers to metal).

Reduced monoclinic BiVO4 for improved photoelectrochemical oxidation of water under visible light.

A monoclinic BiVO4 film was grown on a transparent conducting substrate for photoelectrochemical oxidation of water. A photocurrent up to 2.3 mA cm(-2) under visible light (λ > 420 nm) was achieved after treating the sample simply by electrochemical reduction followed by NaBH4. The high photocurrent is believed to be due to the improved carrier separation and transportation as a result of increased donor density.

Dense layers of vertically oriented WO3 crystals as anodes for photoelectrochemical water oxidation.

Films of crystalline WO(3) nanosheets oriented perpendicular to tungsten substrates were grown by a surfactant-free hydrothermal method, followed by sintering. The films exhibit photoelectrochemical oxygen evolution at low overpotential.