ABSTRACT
Dentin, the mineralized tissue forming the bulk of the tooth, serves as an energy-absorbing cushion for the hard, wear-resistant enamel and protects the inner soft tissues. Several studies used fracture mechanics methods to study the fracture toughness of dentin. However, all of them utilized precracks and cannot be used to estimate the intrinsic critical flaw size of dentin. We applied quantitative fractography to study the fracture pattern and fracture toughness of human dentin. Sixteen specimens were prepared from the coronal dentin and fractured in three-point flexure. Fracture surfaces were examined using a scanning electron microscope and the fracture toughness was calculated using a fracture mechanics equation. It was found that human dentin has a fracture surface similar to those of brittle materials. Twist hackle markings were observed and were used to identify the fracture origins. Average fracture toughness of all specimens was found to be 2.3 MPa m(1/2) and the average critical flaw size was estimated to 120 mum. It is suggested that fractography is a promising technique in analyzing the fracture of dentin under catastrophic failure.
Subject(s)
Dentin/injuries , Tooth Fractures , Biomechanical Phenomena , Dentin/physiopathology , Humans , Stress, Mechanical , Surface PropertiesABSTRACT
Ceramic systems have limited long-term fracture resistance, especially when they are used in posterior areas or for fixed partial dentures. The objective of this study was to determine the site of crack initiation and the causes of fracture of clinically failed ceramic fixed partial dentures. Six Empress 2 lithia-disilicate (Li(2)O x 2SiO(2))-based veneered bridges and 7 experimental lithia-disilicate-based non-veneered ceramic bridges were retrieved and analyzed. Fractography and fracture mechanics methods were used to estimate the stresses at failure in 6 bridges (50%) whose fracture initiated from the occlusal surface of the connectors. Fracture of 1 non-veneered bridge (8%) initiated within the gingival surface of the connector. Three veneered bridges fractured within the veneer layers. Failure stresses of the all-core fixed partial dentures ranged from 107 to 161 MPa. Failure stresses of the veneered fixed partial dentures ranged from 19 to 68 MPa. We conclude that fracture initiation sites are controlled primarily by contact damage.
Subject(s)
Dental Porcelain , Dental Restoration Failure , Denture, Partial, Fixed , Compressive Strength , Dental Stress Analysis , Dental Veneers , Elasticity , Equipment Failure Analysis , Humans , Lithium Compounds , Materials Testing , Pliability , Surface PropertiesABSTRACT
The aim of this study was to investigate the effect of saliva contamination on the bond strengths of three one-bottle bonding systems. The dentin of 90 recently extracted, non-carious human molar teeth was exposed and ground wet on 500 grit silicon carbide (SIC) paper to establish a bonding surface in superficial dentin. Specimens were randomly assigned to nine groups of 10 teeth each. Three testing conditions are: (i) contamination with fresh saliva (pH 5.5) after acid etching, (ii) contamination with fresh saliva after bonding application, and (iii) no contamination. Three adhesive systems are: syntac single component, prime & bond NT, and gluma one bond. Cylinders of composite were applied via PTFE (polytetrafluroethylene) split mould and light cured to the dentin surfaces. All specimens were thermocycled (5000 cycles) between baths of 5 and 55 degrees C. Shear bond strengths were measured using an Instron Universal testing machine at a crosshead speed of 1 mm min-1. Two-way ANOVA was used to analyse the data. The results of this study indicated that the saliva contamination of dentin has no adverse effect on the bonding efficiency of one-bottle adhesive systems (P > 0.05). No statistically significant differences were found between the shear bond strengths of tested adhesives.
Subject(s)
Dental Bonding , Dentin-Bonding Agents , Resin Cements , Saliva , Adhesives , Analysis of Variance , Dentin , Drug Contamination , Hot Temperature , Humans , Materials Testing , Molar , Polymethacrylic Acids , Random Allocation , Technology, Dental , Tensile StrengthABSTRACT
The bond strength of two heat-cured and four cold-cured soft lining materials was compared using a peeling test method before and after thermocycling. Tested soft lining materials were Molloplast B, Mollosil, Ufigel P, Ufigel C, Permaquick and Permaflex. Six specimens, 6.5 x 2 x 0.3 cm, for each group were prepared according to the manufacturers' instructions. Control groups were stored in a humidor for 24 h, whereas the others were thermocycled in a water bath between the 5 and 55 degrees C for 5000 cycles. Peel strength of samples were measured using an Instron Universal testing machine at a cross-head speed of 5 mm min-1. The types of failure were observed using an electron microscope. The highest peel bond strength values were calculated for Permaflex and Permaquick before and after thermocycling, respectively. Molloplast B, Mollosil, Ufigel P and Permaquick demonstrated an increase in peel strength after thermocycling, with Permaquick lining material having statistically significant increase. However, decrease in peel strength was observed for Ufigel C and Permaflex after thermocycling. Failure mode within the control groups was cohesive for Molloplast B, Permaquick and Permaflex, whereas adhesive for Ufigel P and Ufigel C. Mollosil demonstrated a mixed mode of failure for both thermocycled and control groups.
