ABSTRACT
In this paper, for the first time, to the best of our knowledge, we experimentally demonstrate the use of a curved organic light emitting diode (OLED) as a transmitter (Tx) in the non-line-of-sight (NLOS) optical camera communication (OCC) link for an indoor environment using a camera as a receiver. The proposed NLOS-OCC scheme is evaluated for the signal-to-noise ratio (SNR) and the reception success rates R r s under key photographic and communication parameters, including exposure times t e x p and gain values G v, as well as the transmission frequency f s and the distance L. The SNR analysis is performed using a binary classification procedure based on a Gaussian mixture model for the first time, to the best of our knowledge, for OLED-based NLOS-OCC links. We also derive and demonstrate that the effect of G v on the SNR with respect to L is minimal based on the pixel illumination model. The initial analysis suggests that, for a wall reflector-based NLOS-OCC link that is 2 m long, the SNR and R r s increase by 1 dB and 4% (83-87%) for f s of 600 Hz, with an increase in t e x p of 1000-1500 µs and G v of 25-45 dB.
ABSTRACT
We present a design approach for a long-distance optical camera communication (OCC) system using side-emitting fibers as distributed transmitters. We demonstrate our approach feasibility by increasing the transmission distance by two orders up to 40 m compared to previous works. Furthermore, we explore the effect of the light-emitting diode (LED) modulation frequency and rolling shutter camera exposure time on inter-symbol interference and its effective mitigation. Our proposed OCC-fiber link meets the forward-error-correction (FEC) limit of 3.8 · 10-3 of bit error rate (BER) for up to 35 m (with BER= 3.35 · 10-3) and 40 m (with BER=1.13 · 10-3) using 2-mm and 3-mm diameter side-emitting fibers, respectively. Our results at on-off keying modulation frequencies of 3.54 kHz and 5.28 kHz pave the way to moderate-distance outdoor and long-distance indoor highly-reliable applications in the Internet of Things and OCC using side-emitting fiber-based distributed transmitters.
ABSTRACT
In this Letter, we propose and demonstrate a novel wireless communications link using an illuminating optical fiber as a transmitter (Tx) in optical camera communications. We demonstrate an indoor proof-of-concept system using an illuminating plastic optical fiber coupled with a light-emitting diode and a commercial camera as the Tx and the receiver, respectively. For the first time, to the best of our knowledge, we experimentally demonstrate flicker-free wireless transmission within the off-axis camera rotation angle range of 0-45° and the modulation frequencies of 300 and 500 Hz. We also show that a reception success rate of 100% is achieved for the camera exposure and gain of 200 µs and 25 dB, respectively.
ABSTRACT
In this paper, we provide a solution based on spatial frequency fsf to study the angular behavior of a flicker-free, short-range indoor multiple-input multiple-output (MIMO) optical camera communications (OCC) link. We focus on the experimental investigation of OCC's performance for the transmitters (Txs) [i.e., light-emitting diode (LED) based arrays] located at the same and different distances from the receiver (Rx) with the off-axis rotation angle θ. We have used two 8×8 distributed LED arrays and a commercial low-cost complementary metal-oxide-semiconductor (CMOS) Raspberry Pi camera with the rolling-shutter capturing mode as the Tx and Rx, respectively. The image and the respective communications link quality metrics are measured in terms of the peak signal-to-noise ratio (PSNR) and the rate of successfully received bits with respect to fsf for different camera shutter speeds (SS). A CMOS image sensor noise characterization is carried in terms of the signal-to-noise ratio (SNR) and PSNR. The proposed study provides a 100% success rate in data reception at the optimum θ of 50° at lower captured values of fsf, which is projected onto the image sensor in the form of pixels. Moreover, the effect of channel saturation over fsf is studied with respect to θ and SS and we show that, for θ exceeding the optimum value along transmission range, the fsf area of the Txs reduces to less than â¼50% of the captured Tx units at θ of 0°, where no data can be fully recovered.
ABSTRACT
In optical camera communications (OCC), the provision of both flicker-free illumination and high data rates are challenging issues, which can be addressed by utilizing the rolling-shutter (RS) property of the image sensors as the receiver (Rx). In this paper, we propose an RS-based multiple-input multiple-output OCC scheme for the Internet of things (IoT) application. A simplified design of multi-channel transmitter (Tx) using a 7.2 × 7.2 cm2 small 8 × 8 distributed light emitting diode (LED) array, based on grouping of LEDs, is proposed for flicker-free transmission. We carry out an experimental investigation of the indoor OCC system by employing a Raspberry Pi camera as the Rx, with RS capturing mode. Despite the small area of the display, flicker-free communication links within the range of 20-100 cm are established with data throughput of 960 to 120 bps sufficient for IoT. A method to extend link spans up to 1.8 m and the data throughput to 13.44 kbps using different configurations of multi-channel Tx is provided. The peak signal-to-noise ratio of ~14 and 16 dB and the rate of successfully received bits of 99.4 and 81% are measured for the shutter speeds of 200 and 800 µs for a link span of 1 m, respectively.
ABSTRACT
Optical camera communications (OCC) research field has grown recently, aided by ubiquitous digital cameras; however, atmospheric conditions can restrict their feasibility in outdoor scenarios. In this work, we studied an experimental OCC system under environmental phenomena emulated in a laboratory chamber. We found that the heat-induced turbulence does not affect our system significantly, while the attenuation caused by fog does decrease the signal quality. For this reason, a novel strategy is proposed, using the camera's built-in amplifier to overcome the optical power loss and to decrease the quantization noise induced by the analog-digital converter of the camera. The signal quality has been evaluated using the Pearson's correlation coefficient with respect to a reference template signal, along with the signal-to-noise ratio that has been empirically evaluated. The amplification mechanism introduced allows our system to receive the OCC signal under heavy fog by gradually increasing the camera gain up to 16 dB, for meteorological visibility values down to 10 m, with a correlation coefficient of 0.9 with respect to clear conditions.
ABSTRACT
This paper investigates the performance of the neural network (NN) assisted motion detection (MD) over an indoor optical camera communication (OCC) link. The proposed study is based on the performance evaluation of various NN training algorithms, which provide efficient and reliable MD functionality along with vision, illumination, data communications and sensing in indoor OCC. To evaluate the proposed scheme, we have carried out an experimental investigation of a static indoor downlink OCC link employing a mobile phone front camera as the receiver and an 8 × 8 red, green and blue light-emitting diodes array as the transmitter. In addition to data transmission, MD is achieved using a camera to observe user's finger movement in the form of centroids via the OCC link. The captured motion is applied to the NN and is evaluated for a number of MD schemes. The results show that, resilient backpropagation based NN offers the fastest convergence with a minimum error of 10-5 within the processing time window of 0.67 s and a success probability of 100 % for MD compared to other algorithms. We demonstrate that, the proposed system with motion offers a bit error rate which is below the forward error correction limit of 3.8 × 10-3, over a transmission distance of 1.17 m.
