Glenoid bone strain after anatomical total shoulder arthroplasty: In vitro measurements with micro-CT and digital volume correlation.

Glenoid implant loosening remains a major source of failure and concern after anatomical total shoulder arthroplasty (aTSA). It is assumed to be associated with eccentric loading and excessive bone strain, but direct measurement of bone strain after aTSA is not available yet. Therefore, our objective was to develop an in vitro technique for measuring bone strain around a loaded glenoid implant. A custom loading device (1500 N) was designed to fit within a micro-CT scanner, to use digital volume correlation for measuring displacement and calculating strain. Errors were evaluated with three pairs of unloaded scans. The average displacement random error of three pairs of unloaded scans was 6.1 µm. Corresponding systematic and random errors of strain components were less than 806.0 µÎµ and 2039.9 µÎµ, respectively. The average strain accuracy (MAER) and precision (SDER) were 694.3 µÎµ and 440.3 µÎµ, respectively. The loaded minimum principal strain (8738.9 µÎµ) was 12.6 times higher than the MAER (694.3 µÎµ) on average, and was above the MAER for most of the glenoid bone volume (98.1%). Therefore, this technique proves to be accurate and precise enough to eventually compare glenoid implant designs, fixation techniques, or to validate numerical models of specimens under similar loading.

A semi-automated quantitative CT method for measuring rotator cuff muscle degeneration in shoulders with primary osteoarthritis.

BACKGROUND: Rotator cuff muscle degeneration is an important parameter to consider when planning shoulder arthroplasty. HYPOTHESIS: We hypothesized that rotator cuff muscle degeneration is correlated with scapulohumeral subluxation in patients planned for anatomical total shoulder arthroplasty (TSA). MATERIALS AND METHODS: We developed a semi-automated quantitative CT method to measure rotator cuff muscle degeneration, and retrospectively analyzed 107 preoperative shoulder CT scans of patients with primary osteoarthritis. On a standardized sagittal-oblique CT slice perpendicular to the scapular axis, two observers measured the cross-sectional areas of residual rotator cuff muscle tissues, normalized by the estimated area of healthy muscles. Muscle degeneration was quantified in a semi-automated manner, and divided into atrophy and fatty infiltration. Scapulohumeral subluxation was determined in 3D as the distance between the humeral head center and the glenoid surface center, projected on the same CT slice, and normalized by the humeral head radius. We tested all potential correlations between muscle degeneration and scapulohumeral subluxation. RESULTS: Muscle degeneration, primarily due to atrophy, predominated in the supraspinatus; it varied from 0.8% to 88.8%. Scapulohumeral subluxation varied from 2.5% to 72.9%, and was mainly in a posterior and postero-superior orientation. There was a significant but weak correlation between the amount of subluxation and both supraspinatus (R=0.207, P=0.032) and infraspinatus (R=0.225, P=0.020) degeneration. Inter- and intra-observer reproducibility of muscle degeneration measurements were both excellent (ICCs range=0.955-0.987 and 0.971-0.988, respectively). CONCLUSION: This new semi-automated CT method allows to quantitatively and reproducibly measure rotator cuff muscle degeneration in shoulders with primary osteoarthritis. Muscle degeneration is weakly correlated with scapulohumeral subluxation in patients planned for anatomical TSA. LEVEL OF EVIDENCE: Level IV. TYPE OF STUDY: Diagnostic retrospective study.

Patients with primary localized high-grade sarcomas of the digestive tract excluding GIST : a retrospective study from the French sarcoma group.

INTRODUCTION: The natural history of localized high-grade sarcomas of the digestive tract (SDT) excluding GIST has been rarely considered owing to their low incidence and heterogeneity. We describe the histoclinical characteristics of SDT and correlate them with patients' outcomes. METHODS: We retrospectively collected medical files from a European database covering connective tissue tumors listed in Europe for about twenty years. Only untreated localized primary high-grade SDT were included. A central histological review was performed for each case. Patients' characteristics were compared and correlated with clinical outcomes. RESULTS: A total of 45 patients were identified. Leiomyosarcomas (LMS) and undifferentiated sarcomas (UDS) were predominant, the former having better overall survival (OS) and progressionfree survival (PFS) while the latter having a worse outcome than the other histological types. Complete remission was obtained in 34 patients (75%) and was associated with male sex, age over 40 years and monofocal tumor. Complete surgery and LMS histology were associated with a better prognosis without any significant difference in baseline characteristics or in treatment modalities. CONCLUSION: Complete surgery and histological type seem to be prognostic indicators of SDT. These results suggest the importance of treating these patients in a reference center.

Importance of trabecular anisotropy in finite element predictions of patellar strain after Total Knee Arthroplasty.

Patellar fracture and anterior knee pain remain major complications after Total Knee Arthroplasty (TKA). Patient-specific finite element (FE) models should help improve understanding of these complications through estimation of joint and bone mechanics. However, sensitivity of predictions on modeling techniques and approaches is not fully investigated. In particular, the importance of patellar bone anisotropy, usually omitted in FE models, on strain prediction is still unknown. The objective of this study was thus to estimate the influence of modeling patellar trabecular anisotropy on prediction of patellar strain in TKA models. We compared FE-derived strain predictions with isotopic and anisotropic material properties using 17 validated FE models of the patella after TKA. We considered both non-resurfaced and resurfaced patellae, in a load-bearing TKA joint. We evaluated and compared the bone volume above a strain threshold and, in addition, estimated if the difference in isotopic and anisotropic predictions was consistent between patellae of different average bone volume fraction. Compared to the anisotropic reference, the isotropic prediction of strained volume was 3.7±1.8 times higher for non-resurfaced patellae and 1.5±0.4 times for resurfaced patellae. This difference was higher for patellae with lower average bone volume fraction. This study indicates that strain predictions acquired via isotropic patellar FE models should be interpreted with caution, especially when patellae of different average bone volume fraction are compared.

Full-field measurement of micromotion around a cementless femoral stem using micro-CT imaging and radiopaque markers.

A good primary stability of cementless femoral stems is essential for the long-term success of total hip arthroplasty. Experimental measurement of implant micromotion with linear variable differential transformers is commonly used to assess implant primary stability in pre-clinical testing. But these measurements are often limited to a few distinct points at the interface. New techniques based on micro-computed tomography (micro-CT) have recently been introduced, such as Digital Volume Correlation (DVC) or markers-based approaches. DVC is however limited to measurement around non-metallic implants due to metal-induced imaging artifacts, and markers-based techniques are confined to a small portion of the implant. In this paper, we present a technique based on micro-CT imaging and radiopaque markers to provide the first full-field micromotion measurement at the entire bone-implant interface of a cementless femoral stem implanted in a cadaveric femur. Micromotion was measured during compression and torsion. Over 300 simultaneous measurement points were obtained. Micromotion amplitude ranged from 0 to 24µm in compression and from 0 to 49µm in torsion. Peak micromotion was distal in compression and proximal in torsion. The technique bias was 5.1µm and its repeatability standard deviation was 4µm. The method was thus highly reliable and compared well with results obtained with linear variable differential transformers (LVDTs) reported in the literature. These results indicate that this micro-CT based technique is perfectly relevant to observe local variations in primary stability around metallic implants. Possible applications include pre-clinical testing of implants and validation of patient-specific models for pre-operative planning.

Measurements of three-dimensional glenoid erosion when planning the prosthetic replacement of osteoarthritic shoulders.

The three-dimensional (3D) correction of glenoid erosion is critical to the long-term success of total shoulder replacement (TSR). In order to characterise the 3D morphology of eroded glenoid surfaces, we looked for a set of morphological parameters useful for TSR planning. We defined a scapular coordinates system based on non-eroded bony landmarks. The maximum glenoid version was measured and specified in 3D by its orientation angle. Medialisation was considered relative to the spino-glenoid notch. We analysed regular CT scans of 19 normal (N) and 86 osteoarthritic (OA) scapulae. When the maximum version of OA shoulders was higher than 10°, the orientation was not only posterior, but extended in postero-superior (35%), postero-inferior (6%) and anterior sectors (4%). The medialisation of the glenoid was higher in OA than normal shoulders. The orientation angle of maximum version appeared as a critical parameter to specify the glenoid shape in 3D. It will be very useful in planning the best position for the glenoid in TSR.

Translation of biomechanical concepts in bone tissue engineering: from animal study to revision knee arthroplasty.

Bone defects in revision knee arthroplasty are often located in load-bearing regions. The goal of this study was to determine whether a physiologic load could be used as an in situ osteogenic signal to the scaffolds filling the bone defects. In order to answer this question, we proposed a novel translation procedure having four steps: (1) determining the mechanical stimulus using finite element method, (2) designing an animal study to measure bone formation spatially and temporally using micro-CT imaging in the scaffold subjected to the estimated mechanical stimulus, (3) identifying bone formation parameters for the loaded and non-loaded cases appearing in a recently developed mathematical model for bone formation in the scaffold and (4) estimating the stiffness and the bone formation in the bone-scaffold construct. With this procedure, we estimated that after 3 years mechanical stimulation increases the bone volume fraction and the stiffness of scaffold by 1.5- and 2.7-fold, respectively, compared to a non-loaded situation.

Design and test of a MEMS strain-sensing device for monitoring artificial knee implants.

This paper describes the development of a polyimide-based MEMS strain-sensing device. Finite element analysis was used to investigate an artificial knee implant and assist on device design and to optimize sensing characteristics. The sensing element of the device was fabricated using polyimide micromachining with embedded thin-metallic wires and placed into a knee prosthesis. The device was evaluated experimentally in a mechanical knee simulator using static and dynamic axial load conditions similar to those encountered in vivo. Results indicates the sensor is capable of measuring the strain associated to the total axial forces in the range of approximately 4 times body weight with a good sensitivity and accuracy for events happening within 1 s time window.

Importance of the subscapularis muscle after total shoulder arthroplasty.

BACKGROUND: The rotator cuff muscles are the main stabilizer of the glenohumeral joint. After total shoulder arthroplasty using anterior approaches, a dysfunction of the subscapularis muscle has been reported. In the present paper we tested the hypothesis that a deficient subscapularis following total shoulder arthroplasty can induce joint instability. METHODS: To test this hypothesis we have developed an EMG-driven musculoskeletal model of the glenohumeral joint. The model was based on an algorithm that minimizes the difference between measured and predicted muscular activities, while satisfying the mechanical equilibrium of the glenohumeral joint. A movement of abduction in the scapular plane was simulated. We compared a normal and deficient subscapularis. Muscle forces, joint force, contact pattern and humeral head translation were evaluated. FINDINGS: To satisfy the mechanical equilibrium, a deficient subscapularis induced a decrease of the force of the infraspinatus muscle. This force decrease was balanced by an increase of the supraspinatus and middle deltoid. As a consequence, the deficient subscapularis induced an upward migration of the humeral head, an eccentric contact pattern and higher stress within the cement. INTERPRETATION: These results confirm the importance of the suscapularis for the long-term stability of total shoulder arthroplasty.

Tightening force and torque of nonlocking screws in a reverse shoulder prosthesis.

BACKGROUND: Reversed shoulder arthroplasty is an accepted treatment for glenohumeral arthritis associated to rotator cuff deficiency. For most reversed shoulder prostheses, the baseplate of the glenoid component is uncemented and its primary stability is provided by a central peg and peripheral screws. Because of the importance of the primary stability for a good osteo-integration of the baseplate, the optimal fixation of the screws is crucial. In particular, the amplitude of the tightening force of the nonlocking screws is clearly associated to this stability. Since this force is unknown, it is currently not accounted for in experimental or numerical analyses. Thus, the primary goal of this work is to measure this tightening force experimentally. In addition, the tightening torque was also measured, to estimate an optimal surgical value. METHODS: An experimental setup with an instrumented baseplate was developed to measure simultaneously the tightening force, tightening torque and screwing angle, of the nonlocking screws of the Aquealis reversed prosthesis. In addition, the amount of bone volume around each screw was measured with a micro-CT. Measurements were performed on 6 human cadaveric scapulae. FINDINGS: A statistically correlated relationship (p<0.05, R=0.83) was obtained between the maximal tightening force and the bone volume. The relationship between the tightening torque and the bone volume was not statistically significant. INTERPRETATION: The experimental relationship presented in this paper can be used in numerical analyses to improve the baseplate fixation in the glenoid bone.

Mechanical interaction between cells and fluid for bone tissue engineering scaffold: modulation of the interfacial shear stress.

An analytical model of the fluid/cell mechanical interaction was developed. The interfacial shear stress, due to the coupling between the fluid and the cell deformation, was characterized by a new dimensionless number N(fs). For N(fs) above a critical value, the fluid/cell interaction had a damping effect on the interfacial shear stress. Conversely, for N(fs) below this critical value, interfacial shear stress was amplified. As illustration, the role of the dynamic fluid/cell mechanical coupling was studied in a specific biological situation involving cells seeded in a bone scaffold. For the particular bone scaffold chosen, the dimensionless number N(fs) was higher than the critical value. In this case, the dynamic shear stress at the fluid/cell interface is damped for increasing excitation frequency. Interestingly, this damping effect is correlated to the pore diameter of the scaffold, furnishing thus target values in the design of the scaffold. Correspondingly, an efficient cell stimulation might be achieved with a scaffold of pore size larger than 300 microm as no dynamic damping effect is likely to take place. The analytical model proposed in this study, while being a simplification of a fluid/cell mechanical interaction, brings complementary insights to numerical studies by analyzing the effect of different physical parameters.

Comparison of polyethylene wear in anatomical and reversed shoulder prostheses.

Wear of polyethylene is associated with aseptic loosening of orthopaedic implants and has been observed in hip and knee prostheses and anatomical implants for the shoulder. The reversed shoulder prostheses have not been assessed as yet. We investigated the volumetric polyethylene wear of the reversed and anatomical Aequalis shoulder prostheses using a mathematical musculoskeletal model. Movement and joint stability were achieved by EMG-controlled activation of the muscles. A non-constant wear factor was considered. Simulated activities of daily living were estimated from in vivo recorded data. After one year of use, the volumetric wear was 8.4 mm(3) for the anatomical prosthesis, but 44.6 mm(3) for the reversed version. For the anatomical prosthesis the predictions for contact pressure and wear were consistent with biomechanical and clinical data. The abrasive wear of the polyethylene in reversed prostheses should not be underestimated, and further analysis, both experimental and clinical, is required.

Targeted mechanical properties for optimal fluid motion inside artificial bone substitutes.

Our goal was to develop a method to identify the optimal elastic modulus, Poisson's ratio, porosity, and permeability values for a mechanically stressed bone substitute. We hypothesized that a porous bone substitute that favors the transport of nutriments, wastes, biochemical signals, and cells, while keeping the fluid-induced shear stress within a range that stimulates osteoblasts, would likely promote osteointegration. Two optimization criteria were used: (i) the fluid volume exchange between the artificial bone substitute and its environment must be maximal and (ii) the fluid-induced shear stress must be between 0.03 and 3 Pa. Biot's poroelastic theory was used to compute the fluid motion due to mechanical stresses. The impact of the elastic modulus, Poisson's ratio, porosity, and permeability on the fluid motion were determined in general and for three different bone substitute sizes used in high tibial osteotomy. We found that fluid motion was optimized in two independent steps. First, fluid transport was maximized by minimizing the elastic modulus, Poisson's ratio, and porosity. Second, the fluid-induced shear stress could be adjusted by tuning the bone substitute permeability so that it stayed within the favorable range of 0.03 to 3 Pa. Such method provides clear guidelines to bone substitute developers and to orthopedic surgeons for using bone substitute materials according to their mechanical environment.

Implants delivering bisphosphonate locally increase periprosthetic bone density in an osteoporotic sheep model. A pilot study.

It is a clinical challenge to obtain a sufficient orthopaedic implant fixation in weak osteoporotic bone. When the primary implant fixation is poor, micromotions occur at the bone-implant interface, activating osteoclasts, which leads to implant loosening. Bisphosphonate can be used to prevent the osteoclastic response, but when administered systemically its bioavailability is low and the time it takes for the drug to reach the periprosthetic bone may be a limiting factor. Recent data has shown that delivering bisphosphonate locally from the implant surface could be an interesting solution. Local bisphosphonate delivery increased periprosthetic bone density, which leads to a stronger implant fixation, as demonstrated in rats by the increased implant pullout force. The aim of the present study was to verify the positive effect on periprosthetic bone remodelling of local bisphosphonate delivery in an osteoporotic sheep model. Four implants coated with zoledronate and two control implants were inserted in the femoral condyle of ovariectomized sheep for 4 weeks. The bone at the implant surface was 50% higher in the zoledronate-group compared to control group. This effect was significant up to a distance of 400mum from the implant surface. The presented results are similar to what was observed in the osteoporotic rat model, which suggest that the concept of releasing zoledronate locally from the implant to increase the implant fixation is not species specific. The results of this trial study support the claim that local zoledronate could increase the fixation of an implant in weak bone.