Catalytic Fast Pyrolysis of Lignin over High-Surface-Area Mesoporous Aluminosilicates: Effect of Porosity and Acidity.

Catalytic fast pyrolysis (CFP) of lignin with amorphous mesoporous aluminosilicates catalysts yields a high fraction of aromatics and a relatively low amount of char/coke. The relationship between the acidity and porosity of Al-MCM-41, Al-SBA-15, and Al-MSU-J with product selectivity during lignin CFP is determined. The acid sites (mild Brønsted and stronger Lewis) are able to catalyze pyrolysis intermediates towards fewer oxygenated phenols and aromatic hydrocarbons. A generalized correlation of the product selectivity and yield with the aluminum content and acidity of the mesoporous aluminosilicates is hard to establish. Zeolitic strong acid sites are not required to achieve high conversion and selectivity to aromatic hydrocarbon because nanosized MCM-41 produces a high liquid yield and selectivity. The two most essential parameters are diffusion, which is influenced by pore and grain size, and the active site, which may be mildly acidic, but is dominated by Lewis acid sites. Nanosized grains and mild acidity are essential ingredients for a good lignin CFP catalyst.

Evaluation of Mediterranean Agricultural Residues as a Potential Feedstock for the Production of Biogas via Anaerobic Fermentation.

Hydrothermal, dilute acid, and steam explosion pretreatment methods, were evaluated for their efficiency to improve the methane production yield of three Mediterranean agricultural lignocellulosic residues such as olive tree pruning, grapevine pruning, and almond shells. Hydrothermal and dilute acid pretreatments provided low to moderate increase in the digestibility of the biomass samples, whereas steam explosion enabled the highest methane yields to be achieved for almond shells at 232.2 ± 13.0 mL CH4/gVS and olive pruning at 315.4 ± 0.0 mL CH4/gVS. Introduction of an enzymatic prehydrolysis step moderately improved methane yields for hydrothermal and dilute acid pretreated samples but not for the steam exploded ones.

Optimization of hydrothermal pretreatment of lignocellulosic biomass in the bioethanol production process.

The natural resistance to enzymatic deconstruction exhibited by lignocellulosic materials has designated pretreatment as a key step in the biological conversion of biomass to ethanol. Hydrothermal pretreatment in pure water represents a challenging approach because it is a method with low operational costs and does not involve the use of organic solvents, difficult to handle chemicals, and "external" liquid or solid catalysts. In the present work, a systematic study has been performed to optimize the hydrothermal treatment of lignocellulosic biomass (beech wood) with the aim of maximizing the enzymatic digestibility of cellulose in the treated solids and obtaining a liquid side product that could also be utilized for the production of ethanol or valuable chemicals. Hydrothermal treatment experiments were conducted in a batch-mode, high-pressure reactor under autogeneous pressure at varying temperature (130-220 °C) and time (15-180 min) regimes, and at a liquid-to-solid ratio (LSR) of 15. The intensification of the process was expressed by the severity factor, log R(o). The major changes induced in the solid biomass were the dissolution/removal of hemicellulose to the process liquid and the partial removal and relocation of lignin on the external surface of biomass particles in the form of recondensed droplets. The above structural changes led to a 2.5-fold increase in surface area and total pore volume of the pretreated biomass solids. The enzymatic hydrolysis of cellulose to glucose increased from less than 7 wt% for the parent biomass to as high as 70 wt% for the treated solids. Maximum xylan recovery (60 wt%) in the hydrothermal process liquid was observed at about 80 wt% hemicellulose removal; this was accomplished by moderate treatment severities (log R(o)=3.8-4.1). At higher severities (log R(o)=4.7), xylose degradation products, mainly furfural and formic acid, were the predominant chemicals formed.

Nanocomposites of polystyrene-b-poly(isoprene)-b-polystyrene triblock copolymer with clay-carbon nanotube hybrid nanoadditives.

Polystyrene-b-polyisoprene-b-polystyrene (PS-b-PI-b-PS), a widely used linear triblock copolymer of the glassy-rubbery-glassy type, was prepared in this study by anionic polymerization and was further used for the development of novel polymer nanocomposite materials. Hybrid nanoadditives were prepared by the catalytic chemical vapor deposition (CCVD) method through which carbon nanotubes were grown on the surface of smectite clay nanolayers. Side-wall chemical organo-functionalization of the nanotubes was performed in order to enhance the chemical compatibilization of the clay-CNT hybrid nanoadditives with the hydrophobic triblock copolymer. The hybrid clay-CNT nanoadditives were incorporated in the copolymer matrix by a simple solution-precipitation method at two nanoadditive to polymer loadings (one low, i.e., 1 wt %, and one high, i.e., 5 wt %). The resulting nanocomposites were characterized by a combination of techniques and compared with more classical nanocomposites prepared using organo-modified clays as nanoadditives. FT-IR and Raman spectroscopies verified the presence of the hybrid nanoadditives in the final nanocomposites, while X-ray diffraction and transmission electron microscopy proved the formation of fully exfoliated structures. Viscometry measurements were further used to show the successful incorporation and homogeneous dispersion of the hybrid nanoadditives in the polymer mass. The so prepared nanocomposites exhibited enhanced mechanical properties compared to the pristine polymer and the nanocomposites prepared by conventional organo-clays. Both tensile stress and strain at break were improved probably due to better interfacial adhesion of the clay-CNT hybrid of the flexible rubbery PI middle blocks of the triblock copolymer matrix.

Iron-modified hydrotalcite-like materials as highly efficient phosphate sorbents.

Highly efficient sorbents for phosphate removal from aqueous solutions based on the calcined forms of Fe(III)-substituted Layered Double Hydroxides (LDH) materials have been developed in this study. Hydrotalcite-like materials with Mg/M(3+) approximately 3 (where M=Al(3+), Fe(3+) or combined) have been synthesized following simple co-precipitation method and were subsequently calcined in air at 450 degrees C. Both as-synthesized and calcined materials were characterized by means of X-ray Diffraction (XRD), Inductively Coupled Plasma Atomic Emission Spectroscopy (ICP-AES), elemental (C) analysis, N(2) porosimetry, Scanning Electron Microscopy (SEM). All the materials were evaluated for the sorption of phosphates by batch equilibrium sorption experiments and kinetic measurements (effect of contact time). It was shown that chlorides or nitrates, being the charge-balancing anions in the LDH structure, are more easily exchanged by phosphates compared to carbonates. In the Fe(III)-modified LDHs, an increase of the Fe loading led to the decrease of the sorption efficiency. The maximum uptake of phosphates for both the Mg-Al LDH and Mg-Fe LDH samples containing mainly carbonates as charge-balancing anions was relatively low (ca.