Differentiating the aromatic positional isomers of methylbuphedrones and methoxybuphedrones via chemical ionization-mass spectrometry.

Discrimination of aromatic positional isomers of methylbuphedrones and methoxybuphedrones was successfully achieved. Meta isomers were discriminated by chemical ionization-tandem mass spectrometry (CI-MS/MS) using acetonitrile as a reagent gas. Furthermore, all the aromatic positional isomers were discriminated by CI-MS/MS using vinyltrimethylsilane as a reagent gas.

Assay of short-chain carboxylic acids in plasma and urine using gas chromatography after extractive alkylation.

After extractive alkylation combined with plasma deproteinization, we used gas chromatography to assay for short-chain carboxylic acids from formic acid to valeric acid in plasma and urine. It was possible to provide highly sensitive analysis with 0.1-3.4 µg/mL as the limit of detection for plasma and 0.6-8.0 µg/mL for urine, with a correlation coefficient of 1.000 for the linear regression calibration curves. For plasma, deproteinization using ultrafiltration before extractive alkylation resulted in a higher sensitivity for acetic, propionic, butyric, and valeric acids compared with the method without deproteinization. The concentrations of formic acid and acetic acid were determined to be 6 µg/mL and 10 µg/mL, respectively, in the tested plasma, and 22 µg/mL and 32 µg/mL, respectively, in the tested urine. Concentrations from propionic acid to valeric acid were ≤ 1.3 µg/mL. In addition, high concentrations of sulfate, phosphate, hydrogen carbonate, ammonium, and/or sodium ions did not remarkably inhibit the derivatization of carboxylic acids, although hydrogen carbonate ions significantly inhibited that of formic acid.

Improvement of Extractive Alkylation Gas Chromatography of Short-chain Carboxylic Acids in Aqueous Solution.

In the analysis of short-chain carboxylic acids such as formic acid and acetic acid in aqueous solution using extractive alkylation gas chromatography, tetrahexylammonium bromide (THAB) as a phase-transfer catalyst (PTC) causes a high intensity and broad peaks in the gas chromatogram, and interfere with the detection of carboxylic acid derivatives. By an easy treatment of the extractive alkylation solution with perchloric acid and n-hexane, it is possible to remove more than 95% of THAB, and to provide good gas chromatogram with a little admixture of carboxylic acid derivatives. The desensitization was 16% at the maximum, the contamination of the glass insert in gas chromatograph and liquid phase in column by THAB was minimized, and trouble in continuous measurement could be avoided.

Transition-Metal-Free Reductive Coupling of 1,3-Butadienes with Aldehydes Catalyzed by Dibutyliodotin Hydride.

In this study, the Bu2SnIH-catalyzed direct coupling of 1,3-dienes with aldehydes was developed. This reaction could be suitable for coupling without the use of transition-metal catalysts. Many types of aldehydes were applied to this reaction. The addition of MeOH promoted the catalytic cycle.

Catalytic Annulation of Diethyl Methylenecyclopropane-1,1-dicarboxylate with 1,1-Dicyanoalkenes.

The catalytic annulation of methylenecyclopropane 1 with 1,1-dicyanoalkenes 2 using a Mg-Sn catalytic system was developed. Selective formation of cyclopentylidenemalonates 3 and spiro[2,3]hexane-1,1-dicarboxylates 4 was accomplished via the choice of a proper solvent and an effective catalytic system.

Catalytic cycloaddition of 2-hydroxy ketones with 1,1-dicyanoalkenes.

A tin-catalyzed reaction of α-hydroxy ketones with 1,1-dicyanoalkenes produced 2-amino-4,5-dihydrofuran-3-nitriles. In the catalytic reaction, tin enolates were generated from α-hydroxy ketones as active catalytic species. The highly basic ability of the Sn-O bonds played an important role in the reactions. This tin-catalyzed reaction was highly atom-economical and required no other metal reagents.

Catalytic [3 + 2] Cycloaddition through Ring Cleavage of Simple Cyclopropanes with Isocyanates.

The catalytic synthesis of γ-butyrolactams was established via [3 + 2]-cycloaddition of cyclopropanes with isocyanates. An organotin iodide ate complex, MgBr(+)[Bu2SnBrI2](-), was employed as an effective catalyst. Simple cyclopropanes that lack aryl or vinyl substituents were useful precursors. Even acyl cyclopropanes were applicable. The hybrid characteristics of a tin complex, acidic MgBr(+) with nucleophilic tin iodide, was responsible for the catalytic reaction.

Transition-metal-free coupling reaction of vinylcyclopropanes with aldehydes catalyzed by tin hydride.

Donor-acceptor cyclopropanes are useful building blocks for catalytic cycloaddition reactions with a range of electrophiles to give various cyclic products. In contrast, relatively few methods are available for the synthesis of homoallylic alcohols through coupling of vinylcyclopropanes (VCPs) with aldehydes, even with transition-metal catalysts. Here, we report that the hydrostannation of vinylcyclopropanes (VCPs) was effectively promoted by dibutyliodotin hydride (Bu2 SnIH). The resultant allylic tin compounds reacted easily with aldehydes. Furthermore, the use of Bu2 SnIH was effectively catalytic in the presence of hydrosilane as a hydride source, which established a coupling reaction of VCPs with aldehydes for the synthesis of homoallylic alcohols without the use of transition-metal catalysts. In contrast to conventional catalytic reactions of VCPs, the presented method allowed the use of several VCPs in addition to conventional donor-acceptor cyclopropanes.

Catalytic cycloaddition of 2-methyleneaziridines with 1,1-dicyanoalkenes.

2-Methyleneaziridine are a good substrate for the catalytic synthesis of cyclopentylidenamines via a [3 + 2] cycloaddition of 1,1-dicyanoalkenes using Bu2SnI2 as an effective catalyst. A C-attack from 2-methyleneaziridine yielded the desired products.

Synthesis of oxazolidinones initiated by regio- and diastereo-controlled crotylation of alpha-dicarbonyl compounds.

A one-pot synthesis of oxazolidinones was initiated via the allylation of alpha-dicarbonyl compounds, accompanying regio- and diastereo-controlled carbon-carbon bond formation on the side chains of the oxazolidinones.

Degradation of Bis(4-Hydroxyphenyl)methane (bisphenol F) by Sphingobium yanoikuyae strain FM-2 isolated from river water.

Three bacteria capable of utilizing bis(4-hydroxyphenyl)methane (bisphenol F [BPF]) as the sole carbon source were isolated from river water, and they all belonged to the family Sphingomonadaceae. One of the isolates, designated Sphingobium yanoikuyae strain FM-2, at an initial cell density of 0.01 (optical density at 600 nm) completely degraded 0.5 mM BPF within 9 h without any lag period under inductive conditions. Degradation assays of various bisphenols revealed that the BPF-metabolizing system of strain FM-2 was effective only on the limited range of bisphenols consisting of two phenolic rings joined together through a bridging carbon without any methyl substitution on the rings or on the bridging structure. A BPF biodegradation pathway was proposed on the basis of metabolite production patterns and identification of the metabolites. The initial step of BPF biodegradation involves hydroxylation of the bridging carbon to form bis(4-hydroxyphenyl)methanol, followed by oxidation to 4,4'-dihydroxybenzophenone. The 4,4'-dihydroxybenzophenone appears to be further oxidized by the Baeyer-Villiger reaction to 4-hydroxyphenyl 4-hydroxybenzoate, which is then cleaved by oxidation to form 4-hydroxybenzoate and 1,4-hydroquinone. Both of the resultant simple aromatic compounds are mineralized.

The reductive amination of aldehydes and ketones by catalytic use of dibutylchlorotin hydride complex.

The reductive amination of aldehydes or ketones using Ph(2)SiH(2) or PhSiH(3) has been effectively promoted by the direct use of Bu(2)SnClH-pyridine N-oxide as a catalyst; this method has advantages in terms of its mild conditions and wide application to various carbonyls and amines, including aliphatic examples.

Dicarboxylic degradation products of nonylphenol polyethoxylates. Determination and structural elucidation in water samples by solid-phase extraction and gas chromatography-mass spectrometry after methylation.

A reliable method combining solid-phase extraction, derivatization and gas chromatography-chemical ionization mass spectrometry (GC-CI-MS) was developed for the measurement, in river and sewage effluent water, of four select model compounds of dicarboxylic metabolites (dm-CA(5-8)P1EC) and other dicarboxylic metabolites (CA(5-8)P1ECs) of nonylphenol polyethoxylates. These selected isomers were referred as dm-CA(5-8)P1ECs because they have an alpha,alpha-dimethyl configuration (expressed as "dm"), five to eight C atoms and a carboxyl group in the alkyl chain, and an ethoxy acetic acid group. The derivatization of terminal carboxyl groups was successful with (trimethylsilyl)diazomethane. The best extraction conditions were obtained using an Oasis HLB cartridge as a sorbent bed and 4 ml of MTBE/methanol (9:1, v/v) elution mixture. The method detection limits of 0.03-0.07 microg/l for dm-CA(5-8)P1ECs were attained in 500 ml pure water. The recovery was then evaluated for pure water, river and sewage effluent water samples. The high recoveries of typically >89% for each isomer indicated the high performance of the method. Although dm-CA(5-8)P1ECs were not detected in the collected water samples, 21 isomers of CA(5-8)P1ECs were identified by CI-MS and the tentative structures of six out of them were elucidated, mainly limited to the branch at alpha-C atom, by studying the EI-mass spectra. The relative concentrations of individual CA(5-8)P1EC metabolites were calculated based on dm-CA(5-8)P1ECs. The results showed that the main degradation on the nonyl chain occurred via the elimination of two carbon-units and the concentrations in Japan were much lower than those in Taiwan and Italy.

Ion-pair solid-phase extractive derivatization of 4-alkylphenols with pentafluoropyridine for gas chromatography-mass spectrometry.

The ion-pair solid-phase extraction (SPE) of 4-alkylphenols followed by derivatization with pentafluoropyridine is demonstrated. Under alkaline conditions, the 4-alkylphenols could be efficiently adsorbed on a C18 SPE cartridge conditioned with an ion-pair reagent, tetra-n-hexylammonium bromide. The ion pairs, ammonium phenolates, formed on the C18 solid phase, were eluted with a solvent containing the derivatizing reagent, pentafluoropyridine, and completely derivatized during the elution. After optimization of the adsorption and derivatization, we established a method for the determination of the 4-alkylphenols in water samples. The method showed good linearity between 20 and 1000 ng (200-10,000 ng for nonylphenol). By processing 20-ml samples, the method detection limits (MDL) were in the range of 5.2-8.9 ng/l for the 4-alkylphenols (76 ng/l for nonylphenol). To evaluate its applicability to a real aqueous matrix, several river water samples were analyzed.

Sorption of biodegradation end products of nonylphenol polyethoxylates onto activated sludge.

Nonylphenol(NP), nonylphenoxy acetic acid (NP1EC), nonylphenol monoethoxy acetic acid (NP2EC), nonylphenol monoethoxylate (NP1EO) and nonylphenol diethoxylate (NP2EO) are biodegradation end products (BEPs) of nonionic surfactant nonylphenolpolyethoxylates (NPnEO). In this research, sorption of these compounds onto model activated sludge was characterized. Sorption equilibrium experiments showed that NP, NP1EO and NP2EO reached equilibrium in about 12 h, while equilibrium of NP1EC and NP2EC were reached earlier, in about 4 h. In sorption isotherm experiments, obtained equilibrium data at 28 degrees C fitted well to Freundlich sorption model for all investigated compounds. For NP1EC, in addition to Freundlich, equilibrium data also fitted well to Langmuir model. Linear sorption model was also tried, and equilibrium data of all NP, NP1EO, NP2EO and NP2EC except NP1EC fitted well to this model. Calculated Freundlich coefficient (K(F)) and linear sorption coefficient (K(D)) showed that sorption capacity of the investigated compounds were in order NP > NP2EO > NP1EO > NP1EC approximately NP2EC. For NP, NP1EO and NP2EO, high values of calculated K(F) and K(D) indicated an easy uptake of these compounds from aqueous phase onto activated sludge. Whereas, NP1EC and NP2EC with low values of K(F) and K(D) absorbed weakly to activated sludge and tended to preferably remain in aqueous phase.

Liquid-phase microextraction of tributyltin and triphenyltin coupled with gas chromatography-tandem mass spectrometry. Comparison between 4-fluorophenyl and ethyl derivatizations.

This paper describes the liquid-phase microextraction (LPME) of tributyltin (TBT) and triphenyltin coupled with gas chromatography-tandem mass spectrometry. The 4-fluorophenylation and ethylation reactions were used for the derivatization of the organotins. For the two derivatizations, the LPME parameters such as organic solvent, stirring rate, temperature, extraction time and the other additional conditions were examined. Using pure water, the calibration curves, method detection limits (MDLs) and reproducibilities (RSDs) of the two derivatizations were compared under the respective optimized procedures. The 4-fluorophenyl derivatization, which showed a lower MDL (0.36 ng/l) and better reproducibility (RSD = 11% at 10 ng/l) for TBT, was applied to the analysis of seawater. The TBT was detected in the range from 1.1 to 2.0 ng/l in the seawater samples collected in Osaka Bay.

High performance solid-phase analytical derivatization of phenols for gas chromatography-mass spectrometry.

The solid-phase analytical derivatization of phenols with pentafluoropyridine is performed. Fourteen phenols including chlorophenols and alkylphenols, could be efficiently adsorbed on a strong anion-exchange solid phase, Oasis MAX. The phenols adsorbed on Oasis MAX as phenolate ions were desorbed after derivatization with pentafluoropyridine. After optimization of the adsorption and derivatization, we established a procedure for the determination of the phenols in water samples by means of GC-MS. Under the optimized conditions, calibration curves were linear in the range of 10-1000 ng/l for the alkylphenols (100-10000 ng/l for nonylphenol) and 50-1000 ng/l for the others. By processing 100 ml samples, the method detection limits (MDLs) were in the range of 0.45-2.3 ng/l for the alkylphenols (8.5 ng/l for nonylphenol) and 2.4-16 ng/l for the others. Compared with the biphasic reaction system, the signal-to-noise ratios obtained by the solid-phase analytical derivatization were significantly higher. This is ascribed to the fact that coexisting neutral and acidic compounds are efficiently removed from the sample solution by this solid-phase analytical derivatization system.

Derivatization of tributyltin with sodium tetrakis(4-fluorophenyl)-borate for sensitivity improvement of tandem mass spectrometry.

Derivatization of tributyltin for tandem mass spectrometry is described. Tributyltin (TBT) and triphenyltin (TPT) were derivatized with sodium tetrakis(4-fluorophenyl)borate. After optimization of their MS/MS conditions, derivatization conditions were examined. Under the optimum conditions using in-situ derivatization, the calibration curves for the TBT and TPT were linear in the ranges of 0.4 - 200 and 1.2 - 200 pg of Sn, respectively. The detection limits for TBT and TPT were 0.07 and 0.43 pg of Sn, respectively. In the case of TBT, the detection limit with 4-fluorophenylation was improved about five times compared with that with pentylation (0.35 pg). This improvement is ascribed to the bond-dissociation energy of Sn-aryl being stronger than that of Sn-alkyl. Namely, the selective fragmentation of 4-fluorophenyl TBT resulted in high sensitivity. The relative recoveries of TBT and TPT from seawater were 99 and 109%, respectively. The method was successfully applied to the seawater samples.

Dicarboxylic degradation products of nonylphenol polyethoxylates: synthesis and identification by gas chromatography-mass spectrometry using electron and chemical ionization modes.

The synthesis, mass spectra and detectability of four selected dicarboxylic degradation products (CAPECs) of nonylphenol polyethoxylates (NPEOs) are reported. The selected isomers have an alpha,alpha-dimethyl configuration (expressed as "dm" in their abbreviation), five to eight C atoms and a carboxyl group in the alkyl chain, and a carboxymethoxy acid group (dm-CA5-8P1ECs). The synthesis was successfully accomplished via a reaction sequence that started from anisole. After trimethylsilylation with N,O-bis(trimethylsilyl)acetamide or methylation with (trimethylsilyl)diazomethane, the derivatives of the dm-CA5-8P1ECs were subjected to a GC-electron ionization (EI)-MS and GC-isobutane chemical ionization (CI)-MS. In EI-MS, ion peaks at m/z = 265 and 207, corresponding to the alpha,alpha-dimethyl structures via the benzyl cleavage of carboxyalkyl chain, were the most significant ions of the trimethylsilyl and methyl derivatives, respectively. In CI-MS, the main ion peaks of dm-CA5-, dm-CA6-, dm-CA7-, and dm-CA8P1EC after methylation were at m/z= 129, 143, 157, and 171, respectively, corresponding to the loss of methyl phenoxyacetate from [M+ H]+; meanwhile significant peaks were detected at 321, 335, 349, and 363, corresponding to the loss of the trimethylsilanol after trimethylsilylation. The potential for the identification and quantification of individual branched carboxyalkyl isomeric mixtures of CA5-, CA6-, CA7-, and CA8P1EC metabolites based on corresponding dm-CA5-8P1ECs revealed the advantage of the GC-CI-MS although the detection limits in CI were clearly higher than those in EI.